USER GUIDE 1-PORT 60 GHZ WIRELESSHD KIT Model: 29670 1
TABLE OF CONTENTS Introduction.................................................................................................................................................2 Features......................................................................................................................................................3 Package Contents.......................................................................................................................................4 Device Overview.......
INTRODUCTION Thank you for purchasing the TruLink™ 1-Port 60 GHz WirelessHD Kit. The TruLink™ 1-Port 60 GHz WirelessHD Kit enables high definition wireless transmission between your television and your HDMI components. Enjoy full HD 1080p signal from your computer, Blu-ray player, set-top box, gaming console or other HDMI device to your HDMI enabled television.
FEATURES CONVENIENT Supports wireless transmission up to 33ft/10M in-room (longer distances may be supported depending on the environment)* Plug-and-play solution means no drivers, software, or setup required Auto Power function will automatically turn off the attached component when the transmitter is turned off Transmitter and receiver each have on/off switch to conserve power when not in use Transmitter and receiver are wall-mountable* RELIABLE WirelessHD 1.
PACKAGE CONTENTS (1) 60GHz WirelessHD Transmitting Unit (1) 60GHz WirelessHD Receiving Unit (2) HDMI Cables (2) Power Adapters Remote Control Mounting Bracket User Guide 4
DEVICE OVERVIEW TRANSMITTER UNIT RECEIVER UNIT LED Indicators LED Power Link Color Green Blue Weak Green Strong Green Behavior Indication On The LED will illuminate when the power is connected and the power switch is turned on. Off Blinking The LED will be dark when the power switch is turned off. Unit in sleep mode. On The LED will illuminate to indicate which RX is being selected. Off If the pairing LED is off, user has to reset both devices. Blinking Waiting for link.
DEVICE OVERVIEW TRANSMITTER AND RECEIVER SIDE PANEL VIEW Buttons Reset Press the “RESET” button to reset the system, the system will run through a full reset which takes approximately 5 seconds. CFG (Configure) This button is only for manufacturer usage. TRANSMITTER AND RECEIVER REAR PANEL VIEW Configuration DC-IN Switch HDMI Connect the power adapter to the power DC-IN port. Switch the button to turn on or off the power supply.
DEVICE OVERVIEW REMOTE CONTROL Remote Controller Sleep HDMI The devices will be ready while this button clicking. Switch HDMI port, it is only for multi-HDMI port model.
DEVICE INSTALLATION Step 1 Connect the 60GHz WirelessHD Transmitter with an HDMI cable to an input source, such as a computer or a DVD player. Step 2 Connect the 60GHz WirelessHD Receiver with an HDMI cable to a display device, such as a monitor or projector.
DEVICE INSTALLATION Step 3 Connect both power adapters of the Transmitting and Receiving units to outlets. Step 4 Turn on the power of both the Transmitter and Receiver units.
DEVICE INSTALLATION Step 5 After you have finished the above set up steps, the units will be ready to transmit media. You can power on your source and display device and begin use.
TROUBLESHOOTING The following are some things you can try if you are not getting any or getting poor picture and sound.
TECHNICAL SPECIFICATIONS Standards WirelessHD, HDMI(V1.3 with Deep color) Frequency 60 GHz Input/ Output Interface HDMI interface Antenna Type 36 Antenna Ceramic) Range 10 meters inroom usage, AV Port Physical Specifications Adapter Power LED Indicators Operating Environment (Total System) Array (Integrate Transmitter : 1 Port (CEC pass through) Receiver : 1 Port (CEC pass through) Weight: 367g±10g Dimension: L=187mm / W=85mm / H=44.8mm AC 90-230V @ 60Hz input, DC 12V 1.
TECHNICAL SPECIFICATIONS VIDEO FORMAT Auto detect 17 modes TV mode Resolution 640X480I 640X480P 720X480P 720X576I 720X576P 1280X720P 1920X1080I 1920X1080P VESA mode Resolution 640 X 480 800 X 600 1024 X 768 1280 X 1024 Vertical Refresh Rate 23.94 / 24 Hz 50 Hz 59.94 / 60 Hz X X ● X X ● X X ● X ● X X ● X X ● ● X ● ● Deep Color ● ● ● ● ● ● ● Only support 12bit at 23.
TECHNICAL SPECIFICATIONS AUDIO FORMAT Smple rate (256 Fs) LPCM 2ch 32 kHz 44.1 kHz 48 kHz 88.2 kHz 96 kHz 176.
FCC STATEMENT FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna. FCC Part 15 Class B Statement This device complies with Part 15 of the FCC Rules.
CABLES TO GO™ WARRANTY STATEMENT At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year warranty on this device. If you experience problems due to workmanship or material defect for the duration of this warranty, we will repair or replace this device. To request a Return Merchandise Authorization (RMA) number, contact customer service at 1-800-293-4970 or www.cablestogo.com. Cables To Go 3555 Kettering Blvd. Moraine, OH 45439 1-800-826-7904 www.cablestogo.
IMPORTANT SAFETY INFORMATION ! Do not plug the unit in any outlet that does not have enough current to allow the device to function. Refer to the specifications in this manual for power level of the unit. ! Liquid: If this unit or its corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit. Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can damage the product.
18
For more information on this product or to check for updated drivers, manuals or frequently asked questions please visit our website. www.cablestogo.com VER. 1.0.3.22.
