(US) WIRELESS CONFERENCE ROOM VIDEO HUB - HDMI® AND USB-C® (FR) (ES) Model 29973 EMEA Model 84309 2
Table of Contents INTRODUCTION............................................................................................................... 4 PACKAGE CONTENTS ...................................................................................................... 4 OVERVIEW ...................................................................................................................... 5 TRANSMITTER ........................................................................................................
Introduction 29973 is a Full HD wireless transmission device. This solution delivers uncompressed 1080p full HD video and audio content to your existing HDTV set wirelessly. It operates the transmission in 5.1 GHz~ 5.9 GHz frequencies, and it can adjust its communication frequency automatically in case of interference from another RF system. With built-in Omni-directional antennas, it can transmit uncompressed video content to 7 meters (20 feet) LOS (Line of sight) with no latency.
Product Overview 29973 Transmitter Front of Wireless Transmitter FRONT OF TRANSMITTER DESCRIPTION 1 Source Selection Switch Press switch to select input. Three LED lights indicate hub is powered on. 2 Source LED LED light indicates which source is currently selected. 3 HDMI Input Connect HDMI cable between this port and HDMI output port of source device. 4 HDMI Input Connect HDMI cable between this port and HDMI output port of source device.
29973 Receiver Wireless Receiver RECEIVER DESCRIPTION 9 USB Micro-B Connect to receiver’s power adapter. 10 HDMI Output Connect to HDTV set via an HDMI cable.
Installation Step 1: Setup the transmitter Connect a source device to the transmitter: 1. Connect the supplied power adapter to the DC IN port of the transmitter and a wall socket. Once the transmitter is connected to power the LED indicator lights on the source selection switch will be white. 2. Plug an HDMI cable or USB-C cable into transmitter’s corresponding connector 3. Plug the cable into the Source Device Step 2: Setup the receiver HDTV set connection with receiver 1.
1. After the power cord is plugged into the electrical outlet, the Wireless Conference Room Hub will be turned on and link established automatically. When transmitter power is unplugged, receiver will enter Standby mode (POWER LED of receiver is lit in red) when link is dropped for over 10mins. 2. When receiver is in Standby mode (Receiver POWER LED is lit in red), and transmitter is powered, the transmitter will wake up the receiver and automatically to establish a link. 3.
5. If all operation is normal, the POWER LED and INFO/CHANNEL LED will be solid white. Please refer to the below form containing detailed LED indicator and OSD description of transmitter / receiver: LED/OSD Behavior 1. The power LED will be solid white when the unit is powered on. 2. The source LED will be solid white when the source is selected. (The default setting of the source is HDMI, as indicated by the solid white HDMI LED.
6. If there is no signal to the source input and if the end user plugs in the source cable and a signal is received: 6.1 The TX unit will send the CEC message “TEXT VIEW ON” to turn on the TV set. 6.2 The TX unit will then send the CEC message “ACTIVE SOURCE” to switch to the selected source of the TV set. 7.
Step 4: Mounting the receiver to the Wall 1. 2. 3. 4. 5. Mark pilot holes by holding mounting plate (2) on wall. Drill pilot holes from markings. Insert the supplied anchors (3) into the wall. Mount receiver (5) to mounting plate with the two supplied (4) screws. Align the four holes that had been used for the pilot holes to the four anchors in the wall. 6. Use the four supplied screws (1) to screw into the anchors. Do not over tighten.
Troubleshooting 12
Supported Resolution Audio Bit Rate Support Digital Audio from HDMI inputs: Up to 6Mbit/s bit-rate support. Support AC3 and DTS.
Product Specifications 14
Firmware Update Procedure 1. Connect the 29973 to a Windows 7 or Windows 10 PC/notebook via the Micro-USB interface. 2. Press and hold the Power button. While holding the Power button, plug in the power cable.
3. The power LED will flash 2 times/second. This indicates that the LUD29973 is attempting to ready the firmware update drive. 4. Your notebook/PC will detect the firmware update drive within 3 seconds. When the firmware update drive is detected, the power LED will remain steady on (not flashing), and the PC/notebook will display a message box indicating it discovered a USB mass storage device. 5.
5.1 Select the new ST MCU firmware image file from the PC/notebook. 5.2 Open the 29973 device firmware update drive on your PC/notebook. 5.
drive folder. 5.4 The device will then begin the ST MCU firmware update. The power LED will flash 2 times/second until the firmware update is complete.
5.5 When the firmware update is complete, all five LEDs on the 29973 (power and four source LEDs) will be solid on. 6. Updating the USB type C (Chrontel) firmware 6.1 Select the new Chrontel firmware image file from the PC/notebook. 6.2 Open the 29973 device firmware update drive on your PC/notebook.
6.3 Copy the Chrontel firmware image file and paste it into the 29973 device firmware update drive folder. 6.4 The device will then begin the Chrontel firmware update. The power LED will flash 2 times/second until the firmware update is complete.
6.5 When the firmware update is complete, all five LEDs on the 29973 (power and four source LEDs) will be solid on. 7. To use the newly updated firmware, you must first recycle the power.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20 cm entre le radiateur et votre corps.
