SmartSwitch 9000-6 Slot 9C106 and 9C706 Chassis Setup and Installation Guide 9031993-02
Notice Cabletron Systems reserves the right to make changes in speciÞcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, Þrmware, or software described in this manual is subject to change without notice.
Notice FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
Notice DECLARATION OF CONFORMITY Application of Council Directive(s): ManufacturerÕs Name: ManufacturerÕs Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC Cabletron Systems, Inc. 35 Industrial Way PO Box 5005 Rochester, NH 03867 Mr. J.
Notice iv
Contents Chapter 1 Introduction SmartSwitch 9000-6 Slot 9C106 Overview ................................................................ 1-1 9C106 Chassis ......................................................................................................... 1-1 Features ............................................................................................................ 1-1 The Backplane .................................................................................................
Contents Appendix A SmartSwitch 9000-6 Slot Chassis Security Bars Installing the Security Bars .........................................................................................A-1 Removing Security Bars ..............................................................................................
Chapter 1 Introduction Welcome to the Cabletron Systems SmartSwitch 9000-6 Slot 9C106 and 9C706 Chassis Setup and Installation Guide. This manual provides installation instructions and essential reference information for the Cabletron Systems SmartSwitch 9000-6 Slot networking chassis and its associated modules. NOTE Unless noted differently, the information in this guide applies to both the 9C106 and 9C706 SmartSwitch 9000-6 Slot chassis, which are referred to as either the Ò9C106Ó or the ÒchassisÓ.
Introduction The Backplane The 9C106 SmartSwitch 9000-6 Slot chassis provides six distinct backplane buses, and the 9C706 provides an additional seventh bus, the Cell Transfer Matrix. Each bus serves a particular set of needs. The seven backplane buses are shown in Figure 1-1. System Management Bus 1 System Management Bus 10 Flexible Network Bus 1 Flexible Network Bus 2 Inter-Networking Bus A Inter-Networking Bus B Cell Transfer Matrix Figure 1-1.
Introduction System Management Bus 10 The System Management Bus 10, or SMB-10, performs similar functions to those of the SMB-1 previously discussed in this section. The SMB-10 bus is devoted to the transfer of management data within the chassis, but is used for out-of-band or Local Management operations. The SMB-10 operates at Ethernet speeds of 10 Mbps, and is connected to any manageable module in the chassis.
Introduction Support for All SmartSwitch 9000 Interface Modules The chassis is designed to offer the same networking capabilities as Cabletron Systems original SmartSwitch 9000 chassis, thus supporting the same SmartSwitch 9000 networking interface modules. 9C206-1 Power Supply The 9C206-1 power supply, shown in Figure 1-2, is a 1000 watt, triple output supply that provides power to the SmartSwitch 9000-6 Slot chassis.
Introduction Features Thermal Overload Protection A thermal shutdown circuit is included within the 9C206-1 power supply. This circuit protects the power supply from overheating if a thermal overload occurs. Automatic recovery takes place after the thermal overload condition is corrected. Load Sharing Each 9C206-1 power supply uses a current sharing scheme whereby if two power supplies are used, under all load conditions, each supply provides 50% (± 5%) of the required load on each output.
Introduction SM 9C306 STATUS C O M 1 EPIM-T LNK C O M 2 EPIM Figure 1-3.
Introduction Features Out-of-Band Management Out-of-band management refers to managing the SmartSwitch 9000-6 Slot via a Local Management (LM) connection or an SNMP-based management application that does not use the same network connection to the chassis as Òuser data.Ó Three out-of-band management interfaces are built into the 9C306 System Monitor. Two interfaces are serial RS232 ports: ¥ COM1 supports local management via a VT100 session.
Introduction Chapter 1, Introduction, provides an overview of the 9C106 and 9C706 chassis, provides a list of related documentation., and details the procedures to follow for obtaining assistance from Cabletron Systems. Chapter 2, SmartSwitch 9000-6 Slot Chassis Installation, details the procedures to unpack a chassis and prepare it for use. These procedures may also be followed when replacing or upgrading the core components (power supplies, fan modules, or Media Interface Modules).
Introduction Getting Help For additional support related to this device or document, contact Cabletron Systems using one of the following methods: World Wide Web http://www.cabletron.com/ Phone (603) 332-9400 Internet mail support@cabletron.com FTP ftp://ftp.cabletron.com/ anonymous your email address Login Password To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@cabletron.
Introduction 1-10
Chapter 2 SmartSwitch 9000-6 Slot Chassis Installation This chapter provides guidelines for choosing a site to install the SmartSwitch 9000-6 Slot Chassis. It also provides instructions on unpacking and rack mounting the chassis. Installation instructions for the power supplies, fan tray, System Monitor Module, and media interface modules are also provided. Installation Requirements Only qualiÞed personnel should perform installation procedures.
SmartSwitch 9000-6 Slot Chassis Installation ¥ A standard 3-prong power receptacle must be located within 6 feet of the system. One circuit is recommended for each power supply. The AC wiring for the receptacle must be able to supply 12 amps at 120 volts or 6 amps at 220 volts. Proper grounding for the system must be maintained. Once a suitable site has been chosen, the SmartSwitch 9000-6 Slot chassis may be installed. The unit may be freestanding or rack mounted.
SmartSwitch 9000-6 Slot Chassis Installation Rack Mounting the SmartSwitch 9000-6 Slot Chassis The chassis can be mounted in a standard 19-inch equipment rack. ! CAUTION If the rack is not secured to the ßoor, it is recommended that the SmartSwitch 9000-6 Slot be installed in the bottom half of the rack. This prevents the rack from being top heavy. Read the section, Installation Requirements, in this chapter before completing the following procedure.
SmartSwitch 9000-6 Slot Chassis Installation 9C406 FAN Figure 2-1.
SmartSwitch 9000-6 Slot Chassis Installation Installing a Power Supply Only qualiÞed personnel should perform installation procedures. ! Read the section, Installation Requirements, in this chapter before completing the following procedure. CAUTION At least one power supply must be installed on the front of the SmartSwitch 90006 Slot chassis. An additional power supply can be added to achieve redundancy.
SmartSwitch 9000-6 Slot Chassis Installation c. Firmly plug the power supply into the corresponding connector on the back of the chassis by pushing the power supply until its frame touches the surface of the SmartSwitch 9000-6 Slot chassis. d. Do not force the power supply in place. If significant resistance is encountered before the frame is flush with the chassis, remove the power supply, realign it, and push it in again. e.
SmartSwitch 9000-6 Slot Chassis Installation Installing the 9C306 System Monitor The 9C306 System Monitor is installed in the slot marked SM on the right front side of the SmartSwitch 9000-6 Slot chassis, as shown in Figure 2-3. Install a System Monitor by following the steps below: The ESD (Electrostatic Discharge) wrist strap should be attached before handling the System Monitor Module or SmartSwitch 9000 Interface Modules.
SmartSwitch 9000-6 Slot Chassis Installation Plastic Tab 9C406 9C406 FAN SN PS-2 PS-1 SM 9C306 STATUS C O M 1 C O M 2 REDUNDANCY OL POWER LNK POWER 100% 100% 50% LOAD 0% EPIM-T 50% REDUNDANCY OL LOAD 0% EPIM 9C406 9C406 SN SN 100-125 ~ 4.0A 100-125 ~ 4.0A 200-250V ~ 2.0A 200-250V ~ 2.0A 50/60 Hz 50/60 Hz ESD Wrist Strap Connection ESD WRIST STRAP GROUNDING RECEPTACLE Metal Rail Guides Module Card Figure 2-3.
SmartSwitch 9000-6 Slot Chassis Installation 2. Remove the Fan Module from the protective plastic bag. (Save the bag in the event the unit must be reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD). 3. Examine the Fan Module, carefully checking for damage. If any damage is noted, DO NOT install the Fan module. Contact Cabletron Systems immediately. 4. Hold the sides of the Fan Module. 5. Line up the rails on the Fan Module with the tracks on the chassis. 6.
SmartSwitch 9000-6 Slot Chassis Installation Installing SmartSwitch 9000-6 Slot Interface Modules SmartSwitch 9000 Interface Modules can be installed in any of the six slots that are available. To install Interface Modules, see Figure 2-3 and follow the steps below: ! Observe all antistatic precautions when handling sensitive electronic equipment. CAUTION 1. Remove the blank plate, covering the slot in which the Interface Module will be installed.
SmartSwitch 9000-6 Slot Chassis Installation Powering Up the SmartSwitch 9000-6 Slot Chassis Power up the SmartSwitch 9000-6 Slot chassis by following the steps below: NOTE If two power supplies are installed, repeat the procedure below for each supply. 1. Plug one end of the power cord (supplied with the power supply) into the ac power socket on the lower right front corner of the power supply. 2. Plug the other end of the power cord into an ac receptacle.
SmartSwitch 9000-6 Slot Chassis Installation 2-12
Chapter 3 9C206-1 Power Supply Operation This chapter describes the operation of the SmartSwitch 9000-6 Slot chassis power supply. The chapter also details the use of LANVIEW LEDs for troubleshooting and status information. The 9C206-1 power supply can operate with input voltages ranging from 100Ð250 Vac at 50/60 Hz. Each 9C206-1 provides a maximum of 1000 watts of power to the SmartSwitch 9000-6 Slot.
9C206-1 Power Supply Operation PWR Redundancy LED PWR Status LED POWER REDUNDANCY OL Power Supply Level Indicator 100% 50% LOAD 0% Figure 3-1. 9C206-1 Power Supply LANVIEW LEDs PWR Status LED The PWR Status LED indicates the input and output status of a power supply. The possible states and descriptions of the PWR Status LED are listed in Table 3-1. Table 3-1. PWR Status LED 3-2 LED Color State Description Green Functional The 56-volt, 5-volt, and 3.
9C206-1 Power Supply Operation Power Supply Level Indicator LED The Power Supply Level Indicator LED indicates the percentage of the power supply load. The possible states and descriptions of the Power Supply Level Indicator LED are listed in Table 3-2. Table 3-2. Power Supply Level Indicator LED Segment Number(s) LED Color 1Ð9 Green 10Ð90% of power load being used. No action necessary. 10 Amber Greater than 90% of power supply being used. Warns user of a potential overload condition.
9C206-1 Power Supply Operation 3-4
Chapter 4 Specifications Environment Operating Temperature: 5¡C to 40¡C (41¡F to 104¡F) Storage Temperature: -30¡C to 73¡C (-22¡F to 164¡F) Operating Relative Humidity: 5% to 90% (non-condensing) Regulatory Compliance Safety: UL 1950, CSA C22.2 No. 950, EN 60950, 73/23/EEC, and IEC 950 Electromagnetic Compatibility (EMC): FCC Part 15, VCCI V-3, CSA C108.8, EN 50082-1, 89/336/EEC, and EN 55022 9C106 SmartSwitch 9000-6 Slot Chassis Dimensions 66 H x 43.2 W x 40.
Specifications 9C706 SmartSwitch 9000-6 Slot Chassis Dimensions 66 H x 43.2 W x 40.6 D centimeters (26 H x 17 W x 16 D inches) Weight Unit: 11.36 kilograms (25 pounds) Shipping: 16.82 kilograms (37 pounds) 9C206-1 Power Supply Dimensions 48.3 H x 10.7 W x 36.8 D centimeters (19 H x 4.2 W x 14.5 D inches) Weight Unit: 6.8 kilograms (15 pounds) Shipping: 6.8 kilograms (15 pounds) 9C306-1 System Monitor Module Dimensions 48.3 H x 10.7 W x 36.8 D centimeters (19 H x 4.2 W x 14.
Appendix A SmartSwitch 9000-6 Slot Chassis Security Bars The SmartSwitch 9000-6 Slot chassis is equipped with two security bars that prevent the unauthorized removal of the interface modules. This appendix provides instructions to install the SmartSwitch 9000-6 Slot security bars. Only qualiÞed personnel should perform installation procedures. To install the SmartSwitch 9000-6 Slot chassis security bars, a ßat blade screwdriver is needed.
SmartSwitch 9000-6 Slot Chassis Security Bars 4. To install the top security bar, orient the bar with the securing tabs facing up and toward the chassis. 5. Slide the security bar up, so that the holes of the securing tabs are aligned with the join in the beveled corners of the interface modules. 6. Secure the top security bar to the chassis with the screws that are built into the security bar assembly. Fastening Screws Upper Security Bar Handles Toward Chassis Securing Tabs Figure A-1.
Removing Security Bars Security Bar Interface Module Plastic Tabs MMAC-Plus 6 Chassi s Tighten with screwdriver Figure A-2. Security Bar Installation Removing Security Bars The security bars should remain in place while the SmartSwitch 9000-6 Slot chassis is operating. Remove the security bars by loosening the two screws that hold each bar in place. Slide the security bars out from behind the interface module plastic tabs.
SmartSwitch 9000-6 Slot Chassis Security Bars A-4
