HSIM-W6 Installation Guide WIDE AREA1 WIDE AREA2 HSIM-W6 ASYNC LNK LNK LNK STS STS STS TELCO 9032694 CPU TELCO
Only qualified personnel should perform installation procedures. Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is subject to change without notice.
Notice Industry Canada Notice This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Notice Exclusion of Warranty and Disclaimer of Liability 1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
Notice Declaration of Conformity Application of Council Directive(s): Manufacturer’s Name: Manufacturer’s Address: European Representative Name: European Representative Address: Conformance to Directive(s)/Product Standards: Equipment Type/Environment: 89/336/EEC 73/23/EEC 91/263/EEC Cabletron Systems, Inc. 35 Industrial Way PO Box 5005 Rochester, NH 03867 Mr. J.
Contents CHAPTER 1 INTRODUCTION Structure of this Guide.....................................................................................1-1 Related Documents ..........................................................................................1-2 Document Conventions ...................................................................................1-2 Getting Help ......................................................................................................
Contents System Passwords ..................................................................................2-17 Simple Network Management Protocol (SNMP)....................................2-18 Software and Firmware Upgrades ..........................................................2-21 CHAPTER 3 INSTALLATION Unpacking the HSIM-W6 ..................................................................................3-1 Guidelines for Installations ..............................................................
Contents Status (STS) LED is RED ...........................................................................4-9 Status (STS) LED is AMBER .....................................................................4-9 Status (STS) LED is AMBER (blinking) ..................................................4-10 Status (STS) LED is GREEN....................................................................4-10 Investigating Software Configuration Problems .........................................
Contents APPENDIX C NETWORK INFORMATION WORKSHEETS APPENDIX D FCC PART 68 - USER’S INFORMATION FOR HSIM-W6 APPENDIX E GLOSSARY INDEX viii HSIM-W6 Installation Guide
1 Introduction Welcome to the Cabletron Systems HSIM-W6 Installation Guide. This guide provides basic configuration information, hardware specifications and troubleshooting tips for the HSIM-W6. This document also provides guidelines for routing and bridging over Wide Area Networks (WANs). Structure of this Guide This guide is organized as follows: Chapter 1, Introduction, details document conventions and provides information on getting help.
Chapter 1: Introduction Related Documents Use the READ ME FIRST! document included with the HSIM-W6 to set up a computer before beginning configuration. Use the Cabletron Systems QuickSET Configuration Guide to configure the HSIM-W6. Use the Cabletron Systems CyberMONITOR User’s Guide to monitor the WAN using the CyberMONITOR graphical user interface. Use the appropriate Cabletron Systems WPIM Local Management Guide to connect your HSIM to a WAN using a TELNET connection.
Getting Help Getting Help If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact the Cabletron Systems Global Call Center: Phone (603) 332-9400 Internet mail support@ctron.com FTP Login Password ctron.com (134.141.197.
Chapter 1: Introduction 1-4 HSIM-W6 Installation Guide
2 About the HSIM-W6 The HSIM-W6 (Figure 2-1) offers high-speed Wide Area Network (WAN) access to remote sites via two WAN Port Interface Modules (WPIMs) to the device into which it is installed. The HSIM-W6 supports IEEE 802.1d transparent bridging, IP routing, IPX routing between the host device and the two WAN connections, ISDN, Dynamic Host Configuration Protocol (DHCP), Network Address Translation (NAT), and Inverse Multiplexing (IMUX) between Ethernet LANs across a WAN resource.
Chapter 2: About the HSIM-W6 • The WPIM-SY provides a synchronous serial connection of up to 2.048 Mbps to external communications equipment (e.g., a multiplexer or CSU/DSU). The WPIM-Sync uses a subminiature 26-pin connector that supports the following electrical signal interfaces: • EIA-RS449 • V.35 • EIA-RS232D • X.21 • EIA-RS530 • EIA-530A • RS530 ALT A • RS530A ALT A • The WPIM-DDS provides a 56 Kbps or 64 Kbps Digital Data Service (DDS) connection.
Remote Management Capabilities • The WPIM-T1/DDS provides both a T1 and DDS interface that allows changing between the two interfaces by switching the physical cabling and reconfiguring QuickSET for the desired interface. The WPIM-T1/DDS has the capabilities of both the WPIM-T1 and WPIM-DDS.
Chapter 2: About the HSIM-W6 Optional Feature Hardware Data Compression Module (CSX-COMP/ENCR) — The same industry standard STAC Electronics Stacker LZS Compression algorithm supported by HSIM-W6 software is made available by an optional hardware data compression module that accelerates data compression for the HSIM-W6 over Nailed-up PPP or ISDN and Frame Relay.
HSIM-W6 Firmware Support • Inverse Multiplexing (IMUX) • Dynamic Host Configuration Protocol (DHCP) as defined by RFC 1541 • Network Address Translation (NAT) routing as defined by RFC 1631 • Password Authentication Protocol (PAP) and Challenge Handshake Authentication Protocol (CHAP) under PPP as defined by RFC 1994 • Point-to-Point Protocol Link Quality Monitoring (LQM) as defined by RFC 1333 • Point-to-Point Protocol Multilink Protocol (MP) as defined by RFC 1990 • Integrated Services Digit
Chapter 2: About the HSIM-W6 Inverse Multiplexing NOTE Cabletron Systems products that support Inverse Multiplexing (IMUX), such as the HSIM-W6, CSX400, and HSIM-W84, must exist on both ends of the WAN link for the IMUX function to work. Both bridging and routing functions are disabled when using the IMUX function.
HSIM-W6 Firmware Support HDLC Cabletron Systems has provided the High-level Data Link Control (HDLC) protocol which is used in conjunction with the Inverse Multiplexing (IMUX) feature and the WPIM-HDSL to conserve a user’s WAN bandwidth between two Cabletron Systems products, over a point-to-point connection. Cabletron Systems products such as the HSIM-W6, CSX200, and CSX400 must be in use on both ends of the WAN link for these functions to work.
Chapter 2: About the HSIM-W6 The NAT method allows several DHCP clients on a sub network to connect to WAN clients by allowing the DHCP clients to share a single public IP address. When the HSIM-W6 uses NAT, the NAT method modifies the IP headers and addresses, and the selected fields in upper layer protocol headers.
HSIM-W6 Firmware Support The ANSI standard defines a mechanism for the network to signal the existence of congestion, called Explicit Congestion Notification (ECN) bits. Frame Relay uses FECN (Forward ECN) and BECN (Backward ECN) bits to notify end user devices about network congestion. Although the Frame Relay protocol does not respond to congestion, some higher layer protocols for end user devices may respond to ECNs by recognizing that delays have increased, or that frames have been dropped.
Chapter 2: About the HSIM-W6 In half-duplex operation, the authenticator device challenges the peer device by generating a CHAP challenge, and the challenge contains an MD5 algorithm with a random number that has the encrypted password and system name. The peer device then applies a one-way hash algorithm to the random number and returns this encrypted information along with the system name in the CHAP response. The authenticator then runs the same algorithm and compares the result with the expected value.
HSIM-W6 Firmware Support ISDN ISDN provides an inexpensive switched digital access to remote sites. The ISDN BRI standard provides for two high speed 64 Kbps bearer (B) channels used for voice or data connections and one 16 Kbps signaling data (D) channel used for call setup, signaling and other information. ISDN allows all types of information to be transmitted including voice, data, fax and video. Multiple devices can be linked to a single ISDN connection, each having their own telephone number.
Chapter 2: About the HSIM-W6 ISDN Back-up The ISDN back-up feature provides a back-up link for a remote site or branch office when one or more primary WAN interfaces for a frame relay circuit or a nailed-up PPP connection fails. The WPIM-S/T serves as the backup medium for this primary connection. The WPIM-S/T uses the ISDN interfaces to back-up any primary interfaces which have been configured for ISDN back-up.
HSIM-W6 Firmware Support OSPF, based upon link-state technology, was developed by the Internet Engineering Task Force (IETF). The IETF developed OSPF based upon the shortest path first algorithm to serve large, heterogeneous networks. A key feature of OSPF is the speed in which it responds to topological changes, commonly referred to as “convergence time.” OSPF generates a minimal amount of routing protocol traffic compared to most distance vector protocols.
Chapter 2: About the HSIM-W6 Area Border Router Area Border Routers (ABR) connect networks together. These routers have multiple interfaces and participate in multiple areas. There must be at least one area border router in each area connecting that area to a backbone. An ABR maintains a separate link-state database per area that it is attached to. Designated Router Designated Routers (DR) are used by OSPF to reduce adjacencies.
HSIM-W6 Firmware Support HDSL High-bit rate Digital Subscriber Line (HDSL) technology uses existing copper twisted pair cables designed for conventional analog voice transmission from a telephone carrier servicing area as a low-cost alternative to the quality and speed of fiber optic cables, and provides high-speed full-duplex digital transmission links of up to 1.544 Mbps.
Chapter 2: About the HSIM-W6 Routing — Routing provides a way to transfer user data from source to destination over different LAN and WAN links using one or more network protocol formats. Routing relies on routing address tables to determine the best path for each packet. Routing tables can be seeded (i.e., addresses for remote destinations are placed in the table along with network address masks and a metric for path latency). Routing tables are also built dynamically (i.e.
HSIM-W6 Firmware Support Bridging and Routing Protocol Filtering Filtering is used to allow efficient usage of network resources and provide security for a network and hosts. IP Internet Firewall — The HSIM-W6 supports IP Internet Firewall filtering to prevent unauthorized access to a system and network resources from the Internet or a corporate Intranet. Security can be configured to permit or deny IP traffic.
Chapter 2: About the HSIM-W6 read-write — This access level allows editing of some device configuration parameters not including changing system passwords. super-user — This access level allows full management privileges, allowing access to QuickSET. Simple Network Management Protocol (SNMP) The HSIM-W6 provides SNMP agent support for the following: standard and Enterprise Specific Management Information Bases (MIBs), and support for standard and Enterprise Specific SNMP Traps.
HSIM-W6 Firmware Support • Frame Relay MultiProtocol Encapsulation MIB RFC1490 • OSPF V2 RFC2178 • OSPF V2 MIB RFC1850 Cabletron Enterprise MIBs Cabletron Enterprise MIBs include the following: CTWAN-MIB, CTMIB2-EXT-MIB, CTDOWNLOAD-MIB, CTBRIDGE-MIB, RREV-4-MIB, CTROUTER-MIB, CTFAULT-MIB, CTIP-MIB, CHASSIS-MIB, CTNETDIAG-MIB, IP-MIB, IPX-MIB, CTDEFAULT-MIB, CTNAT-MIB.TXT, CTDHCP-MIB.TXT, CTWAN-IMUX-MIB, CTISDN-DIALCONTROL-MIB, CTISDN-DCHANNEL-MIB, and CTISDN-REMOTEPROFILE-MIB.
Chapter 2: About the HSIM-W6 The following is a list of IP Events that are logged and that create the IP Event Log Change Trap.
HSIM-W6 Firmware Support • IPX has detected Link UP on interface # • IPX has detected Link DOWN on interface # • IPX Primary address has been changed on interface # • IPX Access Control Lists have been enabled on interface # • IPX Access Control Lists have been disabled on interface # • IPX has detected Port UP (WAN devices only) • IPX has detected Port DOWN (WAN devices only) • IPX RIP has been enabled on interface # • IPX RIP has been disabled on interface # • IPX SAP has been enabled
Chapter 2: About the HSIM-W6 2-22 HSIM-W6 Installation Guide
3 Installation This chapter outlines the procedure for attaching the HSIM-W6 to the network. To install the HSIM and WPIMs, you need the following items: • Antistatic wrist strap (provided with the HSIM-W6) • Phillips screwdriver Unpacking the HSIM-W6 Unpack the HSIM-W6 as follows: 1. Remove the shipping material covering the HSIM-W6 in the shipping box. 2. Carefully remove the HSIM-W6 from the shipping box. Leave the module in its non-conductive bag until you are ready to install it. 3.
Chapter 3: Installation • Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at the installation site with fluctuations of less than 10°C (50°F) per hour. • Maintain a two-inch clearance for each side and the back of the device for adequate ventilation. Installing Interface Modules Depending on your specific application, install Cableton Systems WAN Port Interface Modules (WPIMs) and the CSX-COMP/ENCR into the HSIM-W6 before proceeding with the installation of your HSIM-W6.
Installing WAN Port Interface Modules (WPIMs) Standoff Screws WPIM Coverplate HSIM Standoffs Figure 3-1 Removing the WPIM Coverplate 3. Remove and save the two HSIM faceplate screws attaching the faceplate to the HSIM printed circuit board (PCB). Remove the HSIM faceplate (see Figure 3). 4. Carefully align and gently insert the WPIM connector onto the WPIM connector pins on the HSIM-W6. 5. Press down firmly on the WPIM until the pins slide all the way into the connector.
Chapter 3: Installation WPIM Screws WPIM Connector LN K ST S W ID E AR EA 1 HSIM PCB TE LC O LN K ST S AS YN C WPIM Connector Pins HSIM Faceplate Screws LN K ST S W ID E AR EA TE 2 HS LC O IM -W 6 CP U Standoffs 225703 Figure 3-2 Installing a WPIM CSX-COMP/ENCR Installation This section contains instructions on how to install the COMP/ENCR into the HSIM-W6. To help eliminate any potential problems during or after installation, read and understand the following steps: 1.
CSX-COMP/ENCR Installation 3. Install the CSX-COMP/ENCR in the HSIM-W6 by unlocking the top and bottom plastic locking tabs of the module faceplate. Slide out the module and place it on its side with the internal components facing up. NOTE Ensure that the CSX-COMP/ENCR is aligned such that its connector pins correctly align with the D-Type connector on the HSIM-W6. 4. Locate the D-Type connector and the standoffs on the HSIM-W6 (refer to Figure 3-3). 5.
Chapter 3: Installation Installing an HSIM You can install an HSIM-W6 in any Cabletron Systems device that supports HSIM technology (e.g., SmartSWITCH 2200, SmartSWITCH 6000). Refer to the release notes for the version of firmware running on the Cabletron Systems device to ensure that the HSIM-W6 is supported. The following sections provide generic instructions for installing an HSIM-W6 in a SmartSWITCH interface module or in a SmartSWITCH chassis.
Installing an HSIM Standoff Screws Coverplate Faceplate Mounting Screws 225704 Figure 3-4 Removing the HSIM Coverplate 7. Place the HSIM behind the module faceplate. See Figure 3-5. 8. Ensure that the standoffs on the interface module align with the standoff screw holes on the HSIM to prevent bending pins. Then insert the connector pins of the HSIM into the HSIM connector on the interface module. 9. Press down firmly on the back of the HSIM until the pins slide all the way into the connector holes.
Chapter 3: Installation .
Installing an HSIM Installing an HSIM in a SmartSWITCH Chassis To install an HSIM into a SmartSWITCH chassis that supports HSIM technology refer to Figure 3-4 and Figure 3-5, and perform the following steps: 1. Power down the chassis and remove the power cord. 2. Disconnect all network cables from the chassis. Note the ports to which these cables attach. Ensure that you remove the power cord and ONLY the screws required to remove the chassis cover.
Chapter 3: Installation 3-10 HSIM-W6 Installation Guide
4 Troubleshooting Use this chapter in conjunction with the LANVIEW status monitoring and diagnostic LEDs on the HSIM-W6 to diagnose power failures, cable faults and link problems. Figure 4-1 shows the front panel LEDs. Table 4-1 through Table 4-10 describes the LED states. If you are having difficulty installing and configuring the HSIM-W6, perform the following steps: • Check that all cables and connectors have been attached properly. • Verify that power has been applied to the HSIM-W6.
Chapter 4: Troubleshooting Table 4-2 HSIM-W6 ASYNC LED States (Console Connection Only) LED Color Status (STS) State AMBER Console connection; Data Carrier Detect (DCD); No Data Set Ready (DSR) AMBER (blinking) Test mode GREEN Modem with connection; DCD; DSR GREEN (blinking) Modem, no connection; DSR; No DCD RED or GREEN Modem connection; Request To Send(RTS); No Clear To Send(CTS) AMBER (blinking) Traffic; Modem or console connection Link (LNK) Table 4-3 shows the console connection to the
Troubleshooting Table 4-4 HSIM-W6 ASYNC Modem Connection Pinout PIN Description 1 Transmit Data 2 Data Carrier Detect (DCD) 3 Data Set Ready (DSR) 4 Receive Data 5 Ground 6 Data Terminal Ready (DTR) 7 Request to Send (RTS) 8 Clear to Send (CTS) Table 4-5 HSIM-W6 WAN Link (LNK) LED States LED Color OFF WAN interface not configured or not present RED No Link/Connection (Fault) on the WAN interface AMBER Transmit (TX) and/or receive (RX) traffic GREEN Link and port is active GREEN (b
Chapter 4: Troubleshooting Table 4-6 HSIM-W6 WAN Status (STS) LED States for T1, DI, and E1 Ports LED Status (STS) Color State OFF Normal or disabled RED Red Alarm AMBER Yellow alarm AMBER (blinking) Port in test mode GREEN Request to send Table 4-7 HSIM-W6 WAN Status (STS) LED States for DDS Ports LED Status (STS) Color State OFF Normal or disabled RED Not used AMBER Out of Service AMBER(blinking) Port in test mode GREEN Not used Table 4-8 HSIM-W6 WAN Status (STS) LED States for
Troubleshooting HSIM-W6 Hardware Table 4-9 HSIM-W6 WAN Status (STS) LED States for HDSL Ports LED Status (STS) Color State OFF Normal or disabled RED One or both loops not synchronized AMBER Not used AMBER (blinking) Port in test mode GREEN Full (both loops synchronized) Fractional (one lop synchronized) Table 4-10 HSIM-W6 WAN Status (STS) LED States for S/T Ports LED Status (STS) Color State OFF Normal or disabled RED Not used AMBER Not used AMBER (blinking) Port in test mode GREE
Chapter 4: Troubleshooting Processor (CPU) LED is RED Processor has detected a fault condition. • Contact Cabletron Systems Technical Support (refer to Getting Help in Chapter 1). ASYNC Console Connection Link (LNK) LED is OFF There is normal console operation and no traffic on the interface. Link (LNK) LED is RED or GREEN The ASYNC port is connected for modem operation. • Check the cabling and console connection pinout. Link (LNK) LED is AMBER There is traffic on the interface.
Troubleshooting the WAN Status (STS) LED is AMBER (Blinking) The HSIM-W6 is in test mode. • The HSIM-W6 is running its Power-up Diagnostic Tests. • Loopback Testing is underway on the ASYNC interface. Troubleshooting the WAN Link (LNK) LED is OFF The WAN interface is not configured for operation. • Use QuickSET or Local Management to make sure that the WAN interface is configured correctly.
Chapter 4: Troubleshooting Status (STS) LED is OFF WPIM-T1, WPIM-E1, WPIM-DI, or WPIM-DDS Installed in HSIM-W6 The port is operating normally. If it is not, and this LED is OFF the port may be disabled. • Use QuickSET or Local Management to make sure that the WAN interface on the Local device is configured correctly. WPIM-SYNC Installed in HSIM-W6 The port is operating normally. If it is not, and this LED is OFF the port may be disabled or RTS may be inactive.
Troubleshooting the WAN Status (STS) LED is RED WPIM-T1, WPIM-E1, or WPIM-DI Installed in HSIM-W6 is in RED Alarm Mode A RED alarm indicates that the WAN connection is not receiving proper framing or has lost framing. • Verify the use of proper cabling on the WAN connection. • Check Frame Type selection on the WAN Physical Configuration and line coding. • Possible bad cabling between Telco and HSIM-W6.
Chapter 4: Troubleshooting WPIM-DDS Installed in HSIM-W6 The DDS circuit is Out of Service (OOS). • Contact your WAN DDS Service Provider and have them test the operation of your DDS circuit. Status (STS) LED is AMBER (blinking) • Device is in test mode. • The CSX400 is running its Power-up Diagnostic Tests. • Loopback Testing is underway on a WAN circuit.
Investigating Software Configuration Problems Investigating Software Configuration Problems Software problems usually occur when your software configuration contains incomplete or incorrect information. Connection to Device Fails During Software Configuration • For a LAN connection, verify that the IP address matches the IP address previously stored into the configuration of the router.
Chapter 4: Troubleshooting Troubleshooting the Frame Relay Connection There are three troubleshooting tools available. The first has always been available and is LM. The second is the FR Error MIB Table, and reflects LMI or DLCI data errors. The third is new and is available as the Mib Nav command: “fr”. Communication with the FR switch is done through one of two methods: Asynchronous Status Messages — At any time the Fr Switch can send an unsolicited (no polling from us) message to us.
A NOTE WPIM Cable Specifications For all WPIM cables, there is part number information for ordering a standard 20-foot cable or a specified length of cable. The number 20 followed by the part number denotes the standard 20-foot cable. The letter “L” denotes the specified length required in feet or meters. For example: 9372095-3 denotes a 3-foot cable; 9372095-3M denotes a 3-meter cable.
Appendix A: WPIM Cable Specifications Table A-3 provides RJ48 DTE pin assignments. Table A-3 DTE Pin Assignments Pin Signal 1 Receive Ring 2 Receive Tip 3 Not Used 4 Transmit Ring 5 Transmit Tip 6 Not Used 7 Shield Ground 8 Shield Ground Table A-4 provides RJ48 network pin assignments.
WPIM-SY WPIM-SY This section provides the Cabletron Systems part number and connector specifications for the WPIM-SY interface cables. Table A-5 provides the cable and interface types, electrical types, and part numbers for the WPIM-SY. Table A-5 WPIM-SY Interface Cables Cable and Interface Type Electrical Type Part Number RS449 RS422 9380120 V.35 V.35 9380121 RS232 RS232 9380122 X.21 X.
Appendix A: WPIM Cable Specifications EIA-449 Table A-6 shows the connector number, cable assembly description, and connector type. Table A-6 Connector Number EIA-449 Interface Cable Assembly Description 1 Connector Type Sub DB 26-pin male connector EIA-530A ALT A to EIA-449 2 DB-37 pin male connector Table A-7 provides pin assignments for the EIA-449 interface cable.
WPIM-SY Table A-7 EIA-449 Interface Cable Pin Assignment (Continued) Connector 1 EIA-530A ALT A MNEMONIC Connector 2 EIA-449 DIRECT NAME TO CE TM DTE CC CD DCE PIN PAIR DIRECT MNEMONIC TO PIN NAME Ring Indicator 22 15 Incoming Call Test Mode 25 18 Test Mode DCE Ready 6 11 Data Mode DTE Ready 20 12 Terminal Ready IC DTE TM DM DCE TR SHIELD 1 AC Signal Common 23 20 Receive Common RC AB Signal Common 7 19 30 37 Send Common Terminal Ready B Signal Ground SG TR_B SC
Appendix A: WPIM Cable Specifications Table A-9 V.
WPIM-SY EIA-232 Table A-10 shows the connector number, cable assembly description, and connector type. Table A-10 Connector Number EIA-232 Interface Cable Assembly Description 1 Connector Type Sub DB 26-pin male EIA-530A ALT A to EIA-232 2 DB-25 pin male Table A-11 provides pin assignments for the EIA-232 interface cable.
Appendix A: WPIM Cable Specifications X.21 Table A-12 shows the connector number, cable assembly description, and connector type. Table A-12 Connector Number X.21 Interface Cable Assembly Description Connector Type 1 Sub DB 26-pin male EIA-530A ALT A to X.21 2 DB-15 pin male Table A-13 provides pin assignments for the X.21 interface cable. Table A-13 X.21 Interface Cable Pin Assignment Connector 1 EIA-530A ALT A MNEMONIC DIRECT NAME TO BA DCE BB DTE CB DTE CA DCE DB Connector 2 X.
WPIM-SY EIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT A Table A-14 shows the connector number, cable assembly description, and connector type for the EIA-530, EIA-530 ALT A, EIA-530A, and EIA-530A ALT A, interface cables.
Appendix A: WPIM Cable Specifications Table A-15 EIA-530, EIA-530 ALT A, EIA-530A, and EIA-530A ALT A Interface Cable Pin Assignments (Continued) Connector 1 EIA-530A ALT A MNEMONIC DIRECT NAME TO Connector 2 EIA-530 PIN PAIR 15 Transmit Signal Timing A Transmit Signal Timing B 12 12 Transmit Signal Timing B Receive Signal Timing A 17 17 Receive Signal Timing A 9 9 Receive Signal Timing B Transmit Signal Timing A 24 24 Transmit Signal Timing A 11 Transmit Signal Timing B Transmit Signa
WPIM-DDS WPIM-DDS This section provides Cabletron Systems part number and connector specifications for the WPIM-DDS interface cable. The WPIM-DDS has one RJ45 port for a direct connection to a single Digital Data Service (DDS) circuit. Table A-16 provides cable and interface type, and part number information for the WPIM-DDS interface cable, and Table A-17 provides network Pin Assignment information for the DDS interface cable. .
Appendix A: WPIM Cable Specifications WPIM-E1 This section provides the Cabletron Systems part number and connector specifications for the WPIM-E1 interface cable. Table A-18 shows the WPIM-E1 connector number, cable and interface type, connector type and part number information. Table A-18 Connector Number WPIM-E1 Connector Information Cable and Interface Type Connector Type Part Number E1 RJ45 9372095 1 2 Table A-19 provides WPIM-E1 network interface cable pin assignments.
WPIM-E1 Table A-20 provides WPIM-E1 DTE interface cable pin assignments. Table A-20 DTE Interface Pin Signal 1 Receive Ring 2 Receive Tip 3 Shield Ground 4 Transmit Ring 5 Transmit Tip 6 Shield Ground 7 Not Used 8 Not Used Table A-21 provides WPIM-E1 RJ45 network interface cable pin assignments.
Appendix A: WPIM Cable Specifications WPIM-DI This section provides Cabletron Systems part number and connector specifications for the WPIM-DI interface cables. Table A-22 shows the connector number, cable assembly description, cable and interface type, connector type and part number information for the WPIM-DI interface.
WPIM-HDSL Table A-24 provides the WPIM-DI drop and insert interface cable pin assignments. Table A-24 WPIM-DI Drop and Insert Pin Signal 1 Transmit Ring 2 Transmit Tip 3 AC Coupled Ground 4 Receive Ring 5 Receive Tip 6 AC Coupled Ground 7 AC Coupled Ground 8 AC Coupled Ground WPIM-HDSL This section provides connector specifications for the WPIM-HDSL interface cables. Table A-25 provides pin assignments for the RJ-45 network interface connector.
Appendix A: WPIM Cable Specifications WPIM-S/T This section provides connector specifications for the WPIM-S/T interface cable. Table A-26 provides pin assignments for the RJ-45 network interface connector.
B Specifications and Standards Compliance This chapter contains hardware specifications, and safety and compliance standards for the HSIM-W6, and for the individual WPIMs that can be configured with this device.
Appendix B: Specifications and Standards Compliance Individual WPIM Regulatory Compliance The following sections provide regulatory compliance standards for the WPIM-TI, WPIM-SY, WPIM-DDS, WPIM-E1, WPIM-DI, WPIM-S/T, and the WPIM-HDSL. Cabletron Systems reserves the right to change these specifications at any time without notice. WPIM-TI This section describes the environmental specifications and safety and approval requirements for the WPIM-T1.
Individual WPIM Regulatory Compliance WPIM-DDS This section describes the environmental specifications and safety and approval requirements for the WPIM-DDS. Safety — This unit meets the safety requirements of UL1950, and CSA C22.2 No. 950. (EMC) — This unit meets the EMC requirements of FCC Part 15, CSA C108.8, and VCCI V-3. NEBS — This unit meets a minimum of Level 1 NEBS requirements in accordance with Bellcore SR 3580. TELECOM — FCC Part 68, CS-03.
Appendix B: Specifications and Standards Compliance WPIM-S/T This section describes the environmental specifications and safety and approval requirements for the WPIM-S/T. Safety — This unit meets the safety requirements of UC1950, CSA 22.2 No. 950, EN 60950, IEC 950 73/23/EEC. Electromagnetic Compatibility (EMC) — This unit meets the EMC requirements of FCC Part 15, EN 55022, VCCI V-3, CSA/08.8 EN 50082-1, AS/NZS 3548, 89/336/EEC. Telcom (Future) — FCC part 68, CS-03.
C Network Information Worksheets Table C-1 Configuration Section Item System Settings Router Name HSIM-W6 Setting Message System Settings Dial Authentication Password Dial Authentication Password/Secret System Settings ISDN Settings ISDN SPID #1 ISDN SPID #2 ISDN Directory Number #1 ISDN Directory Number #2 ISDN Switch Type System Settings Ethernet IP Address Ethernet IP Address and Subnet Mask System Settings Ethernet IPX Network # Ethernet IPX Network Number Table C-2 Remote Router Configu
Appendix C: Network Information Worksheets Table C-2 Remote Router (Continued) Configuration Section Item Remote Router Database TCP/IP Route Addresses Remote Network’s IP Addresses, Subnet Masks, and Metrics Source WAN IP Address and Subnet Maska Setting Remote WAN IP Address and Subnet Maskb Remote Router Database IPX Routes IPX Routes: Network Number, Hop Count and Ticks Remote Router Database IPX SAPs SAPs: Server Name, Server Type, Network Number, Node Number and Sockets WAN Network Number a
D FCC Part 68 - User’s Information For HSIM-W6 The following instructions are to ensure compliance with the Federal Communications Commission (FCC) Rules, Part 68: 1. All connections to the WPIM-T1, WPIM-DI and WPIM-DDS must be made using standard plugs and jacks. a. The WPIM-S/T must only be connected to the network connected behind an FCC Part 68 registered channel service unit. Direct connection is not allowed. 2.
Appendix D: FCC Part 68 - User’s Information For HSIM-W6 3. If the unit appears to be malfunctioning, it should be disconnected from the telephone lines until you learn if your equipment or the telephone line is the source of the trouble. If your equipment needs repair, it should not be reconnected until it is repaired. 4. The CSU/DSU has been designed to prevent harm to the T1 and DDS network.
FCC Part 68 - User’s Information For HSIM-W6 AFFIDAVIT FOR THE CONNECTION OFCUSTOMER EQUIPMENT TO 1.544 MBPS AND/OR SUBRATE DIGITAL SERVICES For the work to be performed in the certified territory of Telco’s name: State of: Country of: I, , of (Name of Authorized Representative) (Customer Name) (Customer’s Address) (Telephone Number) , being duly sworn, state: I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.
Appendix D: FCC Part 68 - User’s Information For HSIM-W6 I attest that the operator(s) maintainer(s) of the digital CPE responsible for the establishment, maintenance and adjustment of the encoded analog content and billing information has (have) been trained to perform these functions by successfully completing one of the following: Check appropriate one(s). a. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or b.
E Glossary 10BASE-T — IEEE 802.3 standard for the use of Ethernet LAN technology over Unshielded Twisted Pair wiring, running at 10 Mbps. ARP — Address Resolution Protocol. An Internet protocol used to bind an IP address to Ethernet/ 802.3 addresses. ASCII — American Standard Code for Information Interchange. It is an 8-bit code for character representation. AUI — Attachment Unit Interface. An IEEE 802.3 transceiver cable connecting the network device (such as a router) to the MAU (media access unit).
Appendix E: Glossary DHCP — Dynamic Host Configuration Protocol is a protocol for automatic TCP/IP configuration that provides static and dynamic address allocation and management. Dial on Demand — Dial up WAN resources are accessed only when remote access is required and released as soon as the resource is no longer needed. DTE — Data Terminal Equipment. DTE refers to equipment used in a network as the data source and/or destination, such as computers. DTMF — Dual Tone Multi-Frequency.
Glossary IP Address — Internet address. A 32-bit address assigned to devices that participate in a network using TCP/IP. An IP address consists of four octets separated with periods defining network, optional subnet and host sections. IPX (Internet Packet Exchange) — A proprietary Network layer protocol developed by Novell and used in NetWare networks. ISDN — Integrated Services Digital Network.
Appendix E: Glossary Network Layer — Layer 3 of the OSI reference model that provides the protocol routing function. Node — Refers to a termination point for communication links; entity that can access a network. OSI — Open System Interconnection. An international standard developed by ITU (formally CCITT) and ISO (International Organization for Standardization) to facilitate data networking multi-vendor interoperability.
Glossary RS-232 — EIA standard specifying the physical layer interface used to connect a device to communications media. Serialization Frames — Frames sent out by servers under IPX to check whether illegal copies of NetWare are in use on the network. Service Advertising Protocol (SAP) — Protocol used by IPX for broadcasting information about services available on the network, such as file servers, CD-ROM drives and modem pools. SNAP — Sub-Network Access Protocol.
Appendix E: Glossary TELNET — Internet standard protocol for remote terminal emulation that allows a user to remotely log in to another device and appear as if directly connected. TFTP — Trivial File Transfer Protocol. A simplified version of the File Transfer Protocol (FTP) allowing for file transfer between computers over a network.
Index B N Bridge filtering 2-17 Bridging 2-15 Bridging and routing 2-16 Network information worksheets A-1, C-1 E EMC B-2, B-3 EMI B-2, B-3 P PPP 2-4 R F Remote Network Management 2-3 Remote router worksheet C-1 Routing 2-16 Firmware Data Compression 2-6 Flash EEPROMs 2-3 S G Getting Help 1-3 H Hardware specs B-1 I IEEE 802.
Index Index-2 HSIM-W6 Installation Guide
