Use and Care Manual

Cabot
®
Clear Wood Protector
#2101
.The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the
replacement of the defective product, or a refund of its purchase price, at our option.
DESCRIPTION
Cabot
®
Clear Wood Protector is a deep
penetrating waterproofer, combined with dual-
action UV protection and a mold, mildew and
algae resistant coating. The true clear finish and
soap-and-water cleanup makes it easy to apply.
Unlike wax-based clears that sit on top of the
surface and wear away, Clear Wood Protector
penetrates deeply into wood fibers to long-lasting
protection.
PRODUCT FEATURES
 Long-term water beading
 Easy application
 Soap and water cleanup
 Deep penetrating waterproofer
 Dual action UV protection
 Mildew and algae resistant*
*Contains a preservative to inhibit the growth of mildew on the
surface of the coating and prevent discoloration by algae.
FOR USE ON
New or reconditioned wood decks, porches,
outdoor furniture, steps and railings. Also suitable
for stone, masonry, brick and concrete.
TINTING
Do not tint this product.
COVERAGE
100–250 sq. ft. per gallon (9.3–23 m
2
). Rates will
vary depending on porosity of the surface.
DRYING TIME
Dries to touch in 1 hour. Time will vary depending
on temperature and humidity. Recently applied
Cabot Clear Wood Protector may remain slick,
even when dry, until surface has been exposed to
general weathering (rain and sun) for several
days.
SURFACE PREPARATION
Be sure surface is free of all dirt, mildew stains,
loose wood fibers and other foreign matter. In
order to be effective, product must be able to
penetrate. Surfaces must be sound, and may be
dry or damp. If damp, the wood should be free of
puddles and not feel wet. Prepare previously
stained or weathered surfaces with Cabot
®
Problem-Solver
®
Wood Cleaner, Wood Brightener
or Wood Strippers. On untreated weathered
surfaces, scrubbing with a stiff bristle brush or
sanding may be required to completely remove all
loose wood fibers.
Extractive bleeding: Extractive bleeding is not
caused by the coating, nor is it a coating failure.
To remove discoloration caused by extractive
bleeding, use Cabot
®
Problem-Solver
®
Wood
Brightener. Follow directions on label.
Mildew: Any mildew stains present on the surface
prior to application should be removed with
Cabot
®
Problem-Solver
®
Wood Cleaner. Mildew
stains are not caused by the coating, nor do they
represent coating failure. This product contains
agents that inhibit the growth of mildew on the
coating’s film.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint from any surface, you may release lead
dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH
AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead exposure.
Clean up carefully with a wet mop or HEPA
vacuum. Before you start, find out how to protect
yourself and your family by contacting the
USEPA/Lead Information Hotline at 1-800-424-
LEAD (5323) or visit www.epa.gov/lead.
APPLICATION
Apply with nylon or polyester brushes, stain pads,
low-pressure garden sprayer or professional spray
equipment. When spraying, always back-brush
immediately. To ensure desired appearance and
proper drying time, always finish a small test area
before proceeding. Do not overapply. Shake and
stir thoroughly before and during use. If project
requires more than 1 container, blend all
containers together to ensure uniformity. Reapply
every 1–3 years depending on exposure. Use
caution when standing or walking on surfaces still
wet after the application of Cabot
®
Clear Wood
Protector, as the surface may by slippery.
Airless Spray: Recommended tip sizes and
adjustments are 1000–1500 PSI, 0.013–0.015” tip
with fan width of 8–10”. These recommendations
are a starting point only. Due to variability in
sprayers, we recommend testing your spray
pattern and flow before proceeding. If spraying
large surfaces, be sure to back-brush or roll
immediately after spraying. When using HVLP
spray equipment, see manual for proper set-up
instructions.
RESTRICTIONS
For exterior use only. Do not apply when air or
surface temperature is below 40 °F (4 °C) or may
fall below 40 °F (4 °C) for 24 hours after
application. To stain or paint over surfaces treated
with Cabot
®
Clear Wood Protector, allow a period
of up to 12 months for the surface to sufficiently
weather. Allow the surface to dry for 6 hours
before contact with water. Do not thin or combine
with other products. Do not use steel wool on
surfaces that are to be coated with this product.
MAINTENANCE
UV rays (sunlight) and moisture (rain/snow/dew)
are wood’s natural enemies, so minimize
exposure. Evaluate finish each spring and
maintain as needed. Finish durability depends
upon weather, wear and other local conditions,
but finish typically lasts 1–2 years on decks and
1–3 years on siding and fences.