Use and Care Manual
Cabot
®
Australian Timber Oil
#3400 Series
.The data on this sheet represent typical values. Since application variables are a major factor in product performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the
replacement of the defective product, or a refund of its purchase price, at our option.
DESCRIPTION
Cabot
®
Australian Timber Oil
®
is a unique blend
of oils, originally formulated to protect dense
Australian tallowwood, cambara and merbau from
extreme exposures. It is a proven translucent-oil
treatment that is specially formulated for decks,
siding, railings and outdoor furniture. Penetrates
deep into wood to accentuate natural wood depth
and patina.
Containing a precise blend of superb-grade
linseed oil for maximum penetration, long-oil
alkyds for durability and pure tung oil for color
depth and water repellency, it delivers three-way
oil protection. In addition, complex translucent
iron-oxide pigments are added to ensure a lasting
UV-absorbing surface rich with color and
dimension.
PRODUCT FEATURES
Three way oil protection - Tung, Linseed, Alkyd
For decks, siding, railings and outdoor furniture
FOR USE ON
Exterior wood decks, siding, railings, fences and
outdoor furniture.
TINTING
Do not tint this product.
COVERAGE
On smooth surfaces, approximately 400–600 sq.
ft. (37–55 m
2
) per gallon. On rough surfaces, 250–
350 sq. ft. (23–32 m
2
) per gallon.
Square feet can be calculated by multiplying
length and width; e.g., 10' W x 25' L = 250 sq.
ft. Requires a 1-coat application.
DRYING TIME
Approximately 24–48 hours depending on
temperature and humidity. When applied to
decking covered by a canopy or roof structure, the
drying time will be extended.
SURFACE PREPARATION
Read the Lead Warning paragraph. Be sure
surface is free of all dirt, mildew stains, loose
wood fibers and other foreign matter. In order to
be effective, a stain must be able to penetrate.
Surfaces must be sound and absolutely dry.
(Moisture content must be below 15% or wood
must be exposed to dry weather a minimum of 3
to 5 days.) Prepare previously stained or
weathered surfaces with Cabot
®
Problem-Solver
®
Wood Cleaner, Wood Brightener or Wood
Strippers. On untreated weathered surfaces,
scrubbing with a stiff bristle brush or sanding may
be required to completely remove all loose wood
fibers.
For new and weathered wood surfaces, a light
sanding with 80–100 grit sandpaper is
recommended to open the pores for maximum
penetration. Use Cabot
®
Problem-Solver
®
Wood
Stripper #8004 to help remove oil-based finishes
from wood surfaces.
Extractive Bleeding: Extractive bleeding is not
caused by the coating, nor is it a coating failure.
To remove discoloration caused by extractive
bleeding, use Cabot
®
Problem-Solver
®
Wood
Brightener. Follow directions on label.
Mildew: Any mildew stains present on the surface
prior to application should be removed with
Cabot
®
Problem-Solver
®
Wood Cleaner. Mildew
stains are not caused by the coating, nor do they
represent coating failure. This product contains
agents that inhibit the growth of mildew on the
coating’s film.
LEAD WARNING
WARNING! If you scrape, sand or remove old
paint from any surface, you may release lead
dust. LEAD IS TOXIC. EXPOSURE TO LEAD
DUST CAN CAUSE SERIOUS ILLNESS, SUCH
AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD
ALSO AVOID EXPOSURE. Wear a NIOSH-
approved respirator to control lead exposure.
Clean up carefully with a wet mop or HEPA
vacuum. Before you start, find out how to protect
yourself and your family by contacting the
USEPA/Lead Information Hotline at 1-800-424-
LEAD (5323) or visit www.epa.gov/lead.
APPLICATION
Apply with a natural-bristle brush or professional
spray equipment. When spraying, always back-
brush immediately. To ensure desired appearance
and proper drying time, always finish a small test
area before proceeding. Do not overapply. Shake
and stir thoroughly before and during use. If
project requires more than 1 container, blend all
containers together to ensure uniformity. Apply to
small sections at a time (1–3 boards); start at
one edge and follow through to the end of the
boards to avoid lap marks. Apply 1 coat only.
For wood substrates only.
Outdoor furniture: Best results can be achieved
by hand rubbing the finish into the wood grain by
using a soft cloth or lambswool applicator.
Airless Spray: Recommended tip sizes and
adjustments for spray application are 0.013–
0.015” at 1000–1500 PSI with a fan width of 5–8
inches. When using HVLP spray equipment, see
manual for proper set-up instructions. If you must
spray, always back°brush immediately after each
section is coated to ensure proper coverage.
RESTRICTIONS
Overapplication of this product may result in a
glossy appearance, poor drying or sagging. Do
not apply in direct sunlight, to hot surfaces, or
when air or surface temperature is below 50 °F
(10 °C) or may fall below 50 °F (10 °C) for 48
hours after application. Do not apply over wet or
damp surfaces or when rain is imminent. Do not
intermix with any other products. Do not thin.
Do not apply over previously painted or sealed
surfaces. For exterior use only.
MAINTENANCE
UV rays (sunlight) and moisture (rain/snow/dew)
are wood’s natural enemies, so minimize
exposure. Evaluate finish each spring and
maintain as needed. Finish durability depends
upon weather, wear and other local conditions,
but finish typically lasts 1–3 years on decks and
2–4 years on siding and fences.
NOTE TO USER
The appearance of the finish will vary depending
on the porosity and color of the wood surface. To
ensure desired appearance and proper drying
time, always finish a small test area before
proceeding.