Specifications

ManualsBrandsCAC / BDP ManualsAir Conditioner40GVM

5 3 D S --- 9 0 0 --- --- --- 1 1 7 ( 1 1 5 v )

5 3 D S --- 9 0 0 --- --- --- 1 1 8 ( 2 3 0 v )

Installation Instructions

Accessory Condensate Pump

fo r Du ctless S plit Sy stem

Coo ling Only and Heat P ump High Wall Units

(Size 009---036)

NOTE: Read and become familiar with these instructions before

beginning installation.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service,

maintenance, or use can cause explosion, fire, electrical shock, or

other conditions which may cause death, personal injury, or

property damage. Consult a qualified installer, service agency, or

your distributor or branch for information or assistance. The

qualified installer or agency must use factory--authorized kits or

accessories when modifying this product. Refer to the individual

instructions packaged with the kits or accessories when installing.

Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes

and current editions of the National Electrical Code (NEC) NFPA

70. In Canada, refer to current editions of the Canadian electrical

code CSA 22.1.

Recognize safety information. This is the safety--alert symbol

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury. Understand

these signal words; DANGER, WARNING, and CAUTION.

These words are used with the safety--alert symbol. DANGER

identifies the most serious hazards which will result in severe

personal injury or death. WARNING signifies hazards which

could result in personal injury or death. CAUTION is used to

identify unsafe practices which would result in minor personal

injury or product and property damage. NOTE is used to

highlight suggestions which will result in enhanced installation,

reliability, or operation.

UNIT OPERATION HAZARD

Failure to follow this caution may result in unit failure

and/or damage.

Always follow instructions properly.

CAUTION

16’ Transparent

Suction Discharge Tubing

Condensate Pump

Assembly

Low Voltage

Power Cord

Transparent

Detection

Unit Vent Tubing

Detection Unit

5/8” Rubber Elbow

Detection Unit

Mounting Bracket

Wire Ties (6)

Mounting Bracket

Power Cable

Adhesive

A12227

Fig. 1 --- Accessory Condensate Pump Kit

Table 1—Accessory Condensate Pump Kit Contents

ITEM QTY

16---ft Transparent Suction/Discharge Tubing 1

Condensate Pump Assembly 1

L o w --- V o l t a g e P o w e r C o r d 1

Transparent Detection Unit Vent Tubing 1

Power Cable 1

Wire Ties 6

Wall Mount Bracket 1

Adhesive 1

Detection Unit Mounting Bracket 1

5/8--- in Rubber Elbow 1

Detection Unit 1

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.

Before beginning any modification or installation of this kit,

be sure the main electrical disconnect is in the OFF position.

Ensure power is disconnected to the fan coil unit. On some

systems both the fan coil and the outdoor unit may be on the

same disconnect. Tag the disconnect switch with a suitable

warning label. There may be more than one disconnect.

WARNING

Summary of content (12 pages)

PAGE 1
53DS---900--- --- ---117 (115 v) 53DS---900--- --- ---118 (230 v) Accessory Condensate Pump for Ductless Split System Cooling Only and Heat Pump High Wall Units (Size 009---036) Installation Instructions NOTE: Read and become familiar with these instructions before beginning installation.
PAGE 2
GENERAL Table 2—Accessory Package Usage ACCESSORY MODEL NUMBER BASE UNIT 53DS--- 900--- --- --- 117 (115--- 1--- 60) 53DS--- 900--- --- --- 118 (208/230--- 1--- 60) WIRING FIG. NO. WIRING FIG. NO.
PAGE 3
5. Connect one end of the low voltage power cord to the telephone jack socket in the detection unit and route the cord and transparent drain tubing through the knockout on the side of the unit enclosure (see Fig. 6). 6. Determine the mounting location of the pump assembly. The pump assembly must always be above the level of the detection unit. For best operation, it is recommended that the pump assembly be mounted in a vertical position with the flow arrow on the pump pointing up (see Fig. 7).
PAGE 4
Table 3—True Flow Rates (Gallons / Hr) 53DS--- 900--- --- --- 117, 118 Condensate Pump Flow Rates Total tube length, 1/4” flexible hose (C) ft Refer to Fig. 2 for (A), (B), (C) Suction Head (A) ft Discharge Head (B) ft 15 30 60 100 0 5.0 4.7 4.5 4.2 6 4.2 3.9 3.7 3.5 13 3.0 2.9 2.8 2.6 20 2.5 2.0 1.7 26 1.6 1.3 1.1 33 1.1 0.9 0.7 0 3.3 0 3.7 3.4 3.2 2.9 6 2.9 2.6 2.4 2.1 13 0.5 1.8 1.6 1.3 1.2 1.1 20 6.6 0 2.9 2.6 2.4 2.1 6 2.4 2.1 1.8 1.6 1.
PAGE 5
POWER AND ALARM CIRCUIT CONNECTING WIRES DISCHARGE TUBING DETECTION UNIT VENT TUBING LOW VOLT POWER CORD FAN COIL CONDENSATE DRAIN LINE COMDENSATE PUMP ASSEMBLY 5/8" RUBBER HOSE DETECTION UNIT DETECTION UNIT MOUNTING BRACKET SUCTION TUBING A12229 Fig.
PAGE 6
115-1-60 POWER REQUIRED FOR PUMP PUMP ALARM BREAKS SIGNAL OUTDOOR UNIT TERMINAL BLOCK 115-1-60 POWER SUPPLY (from outdoor or dedicated source) WHT BRN YEL BLU optional Fig. 8 --- 009, 012 (115--1--60) WIRING SCHEMATIC A12393 115-1-60 POWER REQUIRED FOR PUMP PUMP ALARM BREAKS SIGNAL WHT OUTDOOR UNIT TERMINAL BLOCK BRN YEL BLU Fig.
PAGE 7
PUMP POWERED FROM OUTDOOR UNIT PUMP ALARM BREAKS SIGNAL BLU OUTDOOR UNIT TERMINAL BLOCK BRN PUMP 208/230-1-60 WHT YEL 208/230-1-60 MAIN POWER SUPPLY Fig. 10 --- (208/230--1--60) WIRING SCHEMATIC A13106 PUMP POWERED FROM INDOOR UNIT PUMP ALARM BREAKS SIGNAL WHT BRN YEL BLU Fig.
PAGE 8
PUMP POWERED FROM INDOOR UNIT PUMP ALARM BREAKS SIGNAL BLU B BRN INDOOR UNIT TERMINAL BLOCK A R DT TO OUTDOOR UNIT G WHT O Y YEL Fig. 12 --- (208/230--1--60) WIRING SCHEMATIC A12396 PUMP POWERED FROM INDOOR UNIT PUMP ALARM BREAKS SIGNAL BLU B BRN INDOOR UNIT TERMINAL BLOCK A DT G O Y TO OUTDOOR UNIT WHT R YEL Fig.
PAGE 9
115-1-60 DEDICATED POWER SUPPLY FOR PUMP PUMP ALARM BREAKS SIGNAL 115-1-60 Dedicated Power Supply Indoor Unit Terminal Block Pump WHT L 115-1-60 N BRN AL AL YE L1 L2 S L BL GND U Legend Field Power Wiring Interconnecting Wiring Pump Wiring Field Splice Connection L1 L2 S L1 Field Power Wiring 208/230-1-60 L2 GND Outdoor Unit Terminal Block A13107 Fig.
PAGE 10
WHT BRN YEL BLU N L AL AL Fig. 16 --- 40GVC 9k, 12k (115--1--60) WIRING SCHEMATIC N L AL AL A13098 WHT BRN YEL BLU Fig. 17 --- 40GVQ 9k, 12k (115--1--60) WIRING SCHEMATIC A13099 BLU BRN WHT YEL Fig.
PAGE 11
BLU BRN WHT YEL Fig. 19 --- 40GVC/Q 18k, 24k, 30k, 36k (208/230--1--60) WIRING SCHEMATIC A13101 BLU BRN WHT YEL Fig.
PAGE 12
CLEANING AND MAINTENANCE ! WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Disconnect all power to unit to avoid possible electrical shock during cleaning or maintenance. Set unit power switch to OFF position. Copyright 2013 CAC / BDP S 7310 W. Morris St. S Indianapolis, IN 46231 At the beginning of each season clean the detection unit. 1.