EAZI CHEF GB MODELS 8200, 8210, 8220, 8230, 8240, 8250, 8260 0063 BQ5588 IMPORTANT Read these instructions carefully so as to familiarise yourself with the appliance before use.
GB 1. General This Appliance complies with BS EN 498:1998 This appliance shall only be used with an approved hose and regulator. The gas cartridge/refillable cylinder is to be used only in the upright position. Note: To ensure satisfactory operation when using a cartridge always start up with a full cartridge and only when the intended period of continuous operation is less than approximately 45 minutes.
Parts included in standard models Part Description Part No.
Model 8240 Model 8250 Model 8260
4. Safety Information Hose The hose must be checked for wear or damage before every use and before connecting to the gas container. Do not use the appliance if it has a damaged or worn hose. Replace the hose. Do not use an appliance that is leaking, damaged or which does not operate properly.
5. EXPLODED VIEW Fig. 2 PARTS LIST A. BBQ Lid B. Fat Pan C. Inspection Hole D. Burner Pan E1. Tripod housing E2. Base Plate E3. Leg F. Stem G. Reversible non-stick Grill Plate H1. BBQ Grid H2. BBQ Deflector Plate I1. Skottel BBQ I2. Skottel Food Warmers (optional extra) J1. BBQ Lid Handle J2. Handle Screw Cap K1. BBQ Lid Handle Bracket Inner K2. BBQ Lid Handle Bracket Outer L. Control Knob M1.Base Plate Air Hole M2.Stem Air Hole N. Burner O. Valve P. Lock Nut Q. Jet R1. German Fitting R2.
6. Assembly Instructions Note: The hose and regulator are not supplied. For details contact your local stockist. Before use it is necessary to assemble the legs. (Please refer to figures 3) 1. Ensure that the locking pins are securely fitted. (These may have been pre-assembled in the factory) (Fig. 3a) 2. Do not over tighten (Fig. 3b) 3. Support the bracket when clipping the tripod support into position (Fig.
I 3B/P (30) and I 3+ (28-30/37) Appliance categories: (DK, FI, NO, NL, SE, AT, DE, BE, ES, FR, IE, IT, PT, GB, CH) Fit the Valve Tailpiece (R2) onto the Valve (O) (Fig.4a) by screwing it on in an anticlockwise direction. Push an 8mm inside diameter Hose onto the Valve Tailpiece (R2) until it is properly seated (See Fig.4a).
7. Fitting and Changing the Gas Container Before fitting the regulator to a gas container, ensure that the seal on the regulator is in position and in good condition. This should be done with every connection. Ensure that the gas container is fitted or changed in a well-ventilated location, preferably outdoors, away from any source of ignition such as naked flames or electric fires and away from other people.
9. Lighting the Appliance Precautions to observe before lighting. After prolonged storage, inspect the Base plate air holes (M1) for insects such as spiders, which could affect gas flow. If there is any evidence of insects / nests, the Base Plate must be removed and any foreign material cleaned out. After checking, re-fit all components into the prescribed position. Use this appliance only on a firm level surface.
10.General Maintenance This appliance does not require scheduled maintenance. Replacing a Blocked Jet: Your Eazi Chef is fitted with a specific size jet (Q) to regulate the correct amount of gas. Should the hole in the Jet (Q) become blocked, this may result in a small flame or no flame at all. Do not attempt to clean the Jet (Q) with a pin or other such device as this may damage the orifice, which could make the appliance unsafe.
12.Storing and Carrying Always allow the unit to cool down before packing any part into its bag. Your CADAC Eazi Chef is supplied with a variety of Carry Bags that offer portability and allow you to conveniently store all components included with your model within the supplied bags. The bags included with your model are as indicated in Table 2.
