))) XENITH SERIES AMPLIFIER INSTALLATION GUIDE
Thank you for purchasing this Cadence Xenith Series amplifier. Cadence has been producing quality car audio electronics for more than 16 years and while so many car audio brands have come and gone, Cadence has withstood the test of time which is a testament to our success. But we know that our success couldn’t have been achieved with out you our customer whose faith in our brand has taken us so far.
))) XENITH POWER AND PROTECTION CIRCUITRY: Xenith Series amplifiers feature our unique IC controlled protection circuitry. This sophisticated circuit constantly monitors the heat sink internal temperature and various voltages, adjusting the amp automatically and protecting it from dangerous conditions.
PROTECTION CIRCUITRY: Cadence amplifiers incorporate many outstanding protection circuits to help protect the amplifier from being damaged during operating conditions. Thermal Protection: When the amplifier reaches an unsafe operating temperature of 80 degrees Celsius the amplifier will turn off.
))) XENITH The wire harness should be made of red primary cable of at least 8 gauge for the Xa125.2 and at least 4 gauge for all other larger models. The harness should terminate in a large ring terminal for connection directly to the positive terminal of the car battery. Use a spade plug to attach the wire, which connects to the amplifier location marked 12V+. A second black color wire of equal gauge should be used as a ground connection to a welded chassis member.
ADJUSTING THE SYSTEM Once the system is operational, the first thing to do, is set all crossover points to approximate settings. In the case of the basic sub woofer system Low Pass filter crossover at 100 Hz or so. Set the Bass Boost equalizer controls to 0 dB ( Flat Switch Position.) Now you should set the amplifiers Input Sensitivity adjustment. The knob accessible on the side of the amplifier marked INPUT GAIN adjusts the input sensitivity from 200mV to 8Volts.
))) XENITH MOUNTING THE AMPLIFIER: Choose a convenient mounting location with unobstructed airflow. The Xenith amplifiers feature four mounting holes located at the amplifiers four corners. Remove the 4 caps which are factory installed in the amplifier side trim panels. Insert the screws and tighten. You should first drill a pilot hole in the location where you wish to mount your amplifier so that when you go install the mounting screws they install easily and straight.
))) MOUNTING DIAGRAM 8 XENITH
POWER / GROUND / REMOTE WIRING - MONO BLOCK SUBWOOFER Xenith Mono Block amplifiers are 2 ohm stable mono blocks. For installation ease we have provided two sets of terminals, but these terminals are wired in parallel inside the amp. Therefore when wiring two woofers, each woofer should never be less than 4 ohm per terminal. When using one 2 ohm woofer you can use any single + and - terminal. Remote turn on from head unit.
2-CHANNEL AMPLIFIER APPLICATIONS remote +12 volts 30 A STEREO SPEAKERS 4 ohm mono bridged left + right + - ))) ground XENITH Xa 125.2 2-ohm stereo 4-ohm mono maximum impedance COMPONENTS BRIDGED SUBWOOFER Bridged 4 ohm Subwoofer full low pass high pass crossover selector 10 2-ohm or 4-ohm Stereo Speakers or Stereo Woofers lowpass crossover full low pass high pass crossover selector 40Hz 160Hz lowpass crossover 4 ohm Component Kit with Passive Crossovers.
4-CHANNEL AMPLIFIER APPLICATIONS 4 ohm mono bridged +12 volts + 40 A xa 175.4 40 A left - + 4 ohm mono bridged right + - left + - right CHANNELS 3 - 4 remote CHANNELS 1 -2 ground COMPONENTS + STEREO SPEAKERS BRIDGED SUBWOOFERS 2-ohm or 4-ohm Component Kits with Passive Crossovers or Multi-Element Coaxial Type Speakers. Two Bridged 4 ohm Subwoofers.
R I G H T 8Volt 200mV input level 40Hz l-pass 600Hz highpass crossover h-pass 40Hz 160Hz lowpass crossover input channels 3-4 full 40Hz l-pass 160Hz lowpass crossover L E F T h-pass 40Hz 600Hz highpass crossover 8Volt CHANNELS 3 - 4 xa 175.4 full output crossover selector channels 1-2 CHANNELS 1 -2 diagnostic output L E F T R I G H T 200mV input level ))) input power XENITH 4-CHANNEL AMPLIFIER APPLICATIONS THREE CHANNEL SYSTEM.
))) XENITH XENITH xa 175.
4 X DUAL VC 8 OHM SPEAKERS WITH SERIES VOICE COILS, ALL IN PARALLEL SERIES: DUAL VOICE COIL SPEAKERS + 2 OHM TO AMPLIFIER 4+4 OHM 4+4 OHM 4+4 OHM Please note that the minimum impedance load for Cadence Xenith series stereo amplifiers is 2 ohm stereo and 4 ohm mono bridged. Mono blocks are 2 ohm mono stable. 4+4 OHM - Lower impedance loads will cause overheating and may damage the amplifiers.
))) XENITH AMPLIFIER SPECIFICATIONS Specifications Type Xa300.1 Xa400.1 Xa125.2 Xa175.2 Xa125.4 Xa175.4 2-Channel 2-Channel 4-Channel 4-Channel Mono Mono Maximum Power-Watts 600 850 500 700 1000 1400 4 ohm RMS Watts N/A N/A 80 x 2 110 x 2 80 x 4 110 x 4 2 ohm RMS Watts 300 425 125 x 2 175 x 2 125 x 4 175 x 4 4 ohm RMS Bridged Mono N/A N/A 250 350 250 x 2 350 x 2 <0.1% <0.1% <0.1% <0.1% <0.1% <0.
COPYRIGHT CADENCE ACOUSTICS LTD. Design & specifications subject to change without prior notice.