INTRODUCTION INTRODUCTION Thank you for choosing this cooker hood. * This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. » In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage. SAFETY PRECAUTION © Never let the children operate the machine.
INSTALLATION INSTRUCTIONS Prepare for installation: DUSTED OPTION RE CIRCULATION OPTION a.If you have an outlet to the outside, your cooker hood can be connected as above picture by means of an pipe (with an interior diameter of 150mm). If you don't have an outlet to the outside, you can go with re circulation mode by using carbon filter. 650~750MM | b.Before installation, turn the ¢. The cooker hood should be unit off and unplug it from the placed at a distance of 650~750 outlet.
APED AIR OUT INSTALLATION M D 206
WALL MOUNTING INSTALLATION Prepare pencil, electric drill, plastic wall anchors and level before installation. Recommended installation height: 700mm Required minimum installation height: 650mm Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the hook onto the wall with the screws & plastic wall anchors provided. Lift the cooker hood and hang onto the wall hook. Need to drill 2x8mm extra holes & fixing screws & plastic wall anchors before installation.
Put the upper chimney into lower chimney . Then pulling out the upper chimney upwards. Adjust to reach the height required. There are 2 methods for installing the chimney cover. Please check the attached pic for reference. 1. After drilling the 2 holes and fixing the bracket, hang the chimney cover by matching the both side 2.
If your cooker hood is going to be used in extraction mode, then you should connect the ducting hose to the ceiling adapter at this point. Fix the upper chimney section to the hanging plate, using the 4 self tapping screws. Slide the lower chimney section onto the angle bars and raise it until it sits just below the upper chimney section. Remove the hanging hook and then slide the lower chimney section downwards, until it rests against the main body of the cooker hood.
Two ways for Way A (Wall mounted): According to the center distance of hole in the back of the slim hood, measure the position and then drill PCs Dummy holes on the wall. Insert the plastic wall anchors into each holes and tighten PCs ST4x30 screws into the plastic wall anchors. Place the slim hood onto the tighten screws. Fix the cooker hood with safety screw. The two safety screw vents are positioned on the back casing, with diameter of 6mm. Put the one-way-valve onto the hood to finish installation.
TELESCOPIC MODEL INSTALLATION Two ways for Way A: To install onto the wall drill 2 holes of 28mm on a suitable place according with the center distance of hole in the back of the cooker hood. Insert the nut into the holes. Insert the screws into the nuts and tight. Put the cooker hood onto the tighten screws. Fix the cooker hood with safety screw. The two safety vents are positioned on the back casing, with diameter of 6mm. Put the one way valve onto the cooker hood.
81 292/492 81 499/699 g| 4 Tighten up pests screws 1.Fix the product body into the cabinet with 12 pes screws. 2.connect the lamp and switch wire and fix the panel on the body and tighten PCs screws per left and right side, finally install the filter. LAMP MODEL INSTALLATION , Method 1(for wooden ceiling): Tox 2 Fix the hanger on wooden ceiling by using = = 4 pes ST4*30 screws. [] | (] Method 2(for cement ceiling): | Fix the hanger on cement ceiling by using pes antiknock screws.
LIFT MODEL INSTALLATION Disassemble PCs supporter (PCs M4*12) and Ipc wire-storage box from the hood (apes ST3*12). Measure the cook top size and make sure it has enough space to put into the product and panel should be fix the cook top surface. After putting the product into the cook top, fix the supporter on the body with screws and adjust the position according to ground height.
OPERATION Push Button OFF Bunion Turn off the fan. Low Speed Button Start the fan at low speed . It is suitable for simmering and cooking which does not make much steam. Medium Speed Button Start the fan at medium speed. This is ideal for ventilation during standard cooking operation. High Speed Button Start the fan at high speed. This is ideal for ventilation when a high density of smoke or steam has been produced. Light Button Used for turning on/off the light.
Electronic Button (Lighting) () ON/OFF key Press this key to turn power/motor on and Off w« Power down key On working condition, press this key to decrease the power one level wi Power up key On working condition, press this key to increase the power one level ® Delay key When motor is on working condition, press one time to set 5 minutes delay, press another time to turn the delay function off. 8; Light key Press one time for turning the lights on, press another time to turn the lights off.
1. 2 Touch control . Digital display key Power down key Power up key Delay key On stand-by and working condition, press this key for 3s, the digital display blinks, we can set the delay power off time from I minute to 9 minutes; press the key again to save the setting. If 10s no pressing, then the setting would be saved automatically. When the motor is on and the delay setting is saved , we can still adjust the setting, and the display window will display the countdown time.
ON/OFF key Power down key On working condition, press this key to decrease the power one level, ( the ON/OFF key light would blink slower than the power was not decreased). I@ wi Power up key On working condition, press this key to increase the power one level, ( the ON/OFF key light would blink faster than the power was not increased). (© Delay key When motor is on working condition, press one time fo set 5 minutes delay, press another time to turn the delay function off.
Timer button Time setting, Press anf hold in stand-by mode. This will go into time setting function.Hour display will flash. SHOO 1.0n stand-by and working condition, the LED would be shut off if 2 minutes without pressing, press any key to turn the LED on. 2.When key lights are off, only ON/OFF and lights key can turn the LED on, On stand-by condition, any key can turn the LED on, all operation based on LED is on function.
® ¢i ON/OFF key Connect power in the standby state, press the key for 0.5 seconds to enter the starting state; when the motor in running state, press one time to enter “I-minute delay shutdown count down” state, the motor would turn off immediately if you press again Speed key press this key to change motor level from low level to middies and high level, it is circle change. Plus key press the key to increase motor level. Minus key press the key to decrease motor level. Timer 1.
ON/OFF key Low speed button Medium speed button High speed button Long touch the button for 5 seconds in off mode, the gesture control function will be locked. Repeat this action, it will be turned on. Light key AUTO-CLEAN Please first touch ON/OFF button, then touch "Auto-Clean" button on the panel. The display mention heating time of 9 minutes and begin to count down. The light for auto clean with start blinking. After preheat time of 9 minutes. The indicating lamp of low speed were lit at the same time.
MAINTENANCE Before cleaning switch the unit off and pull out the plug. IL Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit. II. Bulb Replacement switch the unit off and unplug the appliance. 2.Remove the lamp cover by unscrewing the 2 screws. 3.Unscrew the incandescent bulb 4.Replace with the same type and rated bulb/lamp E14 Incandescent Bulb: (220V E14 Max 40W).
III. Aluminum and charcoal filters replacement In order to install the carbon filter, the grease filter should be detached first. Press the lock and pull it downward. MONTHS 0 MAX.65 °C Aluminum filters: To avoid fires, clean thoroughly once a month or whenever the display pilot lights up (if fitted). To do so,remove the filters and soak in hot water and detergent for an hour If using a dishwasher,position the filters vertically to improve the cleaning process. VI.
TROUBLE SHOOTING Fault Cause Solution . The fan blade is jammed. | Switch off the unit and da rot wort : repair by qualified The motor is damaged. service personnel only. : Replace the LED light Both light and fan Light bulb burn. with correct rating. do not work Power cord is loose. Plug im io the p wore The fan blade i: Theta’ Aden Switch of the unit and repair by qualified Serious Vibration The fan motor is not service personnel only. of the unit fixed tightly. LL.
