Instructions / Assembly

ManualsBrandscadeninc ManualsBathHandheld Bidet Toilet Sprayer in Brushed Nickel

Table Of Contents

Hand Held Bidet - Installation Instructions

Parts Included:

Bidet Sprayer Head

T-valve w/Shut Oﬀ

Flat Rubber Washer

Spiral Metal Bidet Hose

Sprayer Holster & Screws for

Mounting (wall & toilet options)

Before Installation:

Check water supply line: If the line that connects the toilet tank to the water

shuto ﬀvalve is a rigid pipe, you will need to purchase a ﬂexible hose to replace

it before installing the CleanSpa. The length of the hose and size of the

connectors will vary.

Installation:

IMPORTANT!

Manufacturers Recommendation: After each use, TURN OFF the T-valve Shut O ﬀValve to close the water

supply to the Bidet Sprayer Head. Failure to turn o ﬀafter each use may weaken the Bidet Hose/Sprayer Head

or cause ﬂooding. Manufacturer is not responsible for damage which may be caused by failure to follow the

above recommendation.

Turn water supply valve back on at the wall and check for leaks using

plumbers tape when necessary. Wait 5 minutes and check again. If no leaks,

then you are done!

Operation:

Attach one end of Spiral Metal Bidet Hose to open end of T-valve w/Shut O ﬀ

and the other end to the Bidet Sprayer Head. (Image 3)

Disconnect ﬂexible water supply line directly under the toilet tank. Put the

Flat Rubber Washer inside the top of the T-valve w/Shut Oﬀ. Connect

T-valve w/Shut O ﬀat the toilet tank, and reconnect the ﬂexible water

supply line to the bottom of the T-valve. Be sure not to over tighten

connections. (Image 2)

Turn o ﬀwater supply valve for the toilet (at the wall) and ﬂush toilet

(holding down handle) to completely empty the tank. (Image 1)

To stop water wash, push Bidet Sprayer Head button into the “oﬀ” position

(button pushed out towards the spray head)

To adjust the wash spray, gently turn the head of the Bidet Sprayer

counter-clockwise to go from a shower spray to a single stream.

press the button to release the water wash.

(Image 5)

Direct the hand held Bidet Sprayer Head in the appropriate direction and

Open the T-valve Shut O ﬀValve to allow water to ﬂow to the Bidet Sprayer Head.

Mount Sprayer Holster: (Note: when mounting Bidet Sprayer Head, make

sure the spray button is pushed out towards the spray head as pictured,

this is the “oﬀ” position)

a. Wall Mount - using only the Sprayer Holster piece, ﬁnd appropriate

spot on wall near toilet to attach Holster to wall.

b. Toilet Mount - attach Sprayer Holster piece to toilet mount.

Hang mount on side of toilet in desired location.

(Image 4)

Summary of content (2 pages)

PAGE 1
Hand Held Bidet - Installation Instructions Parts Included: Bidet Sprayer Head T-valve w/Shut Oﬀ Flat Rubber Washer Spiral Metal Bidet Hose Sprayer Holster & Screws for Mounting (wall & toilet options) Before Installation: Check water supply line: If the line that connects the toilet tank to the water shuto ﬀvalve is a rigid pipe, you will need to purchase a ﬂexible hose to replace it before installing the CleanSpa. The length of the hose and size of the connectors will vary.
PAGE 2
Hand Held Bidet Holder - Installation Instructions Installation: 1)Clean the surface from oil/dust water to keep it at and dry. (For little non-smooth surfaces, please use two-side adhesive pad rst.) (Image 1) 2 2)Tear the protective lm of the sucker. Press the hand held bidet to push out the air. (Image 2) 3)Clockwise tighten the circular torsional ring at the bottom, make the hand held bidet rmly xed. (Image 3) (Counterclockwise release, remove it to change the position. Place it where you want it.