OWNER’S GUIDE COM-PAK BATH WARMTH FOR EVERY MORNING Thank you for your purchase! Question or problem? Let us solve it with a single phone call, email or online chat! We’ll save you a trip back to the store! Cadet Customer Service Phone: 855.CADET.US (855.223.3887) email: customerservice@cadetheat.com Live chat: cadetheat.com (contact us) For how-to videos or more information, please visit: http://cadetheat.com/install/bath ESPAÑOL ver la guía del propietario en cadetheat.com/espanol/bath cadetheat.
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before 6. To disconnect heater, turn control(s) to off, and turn off power to installing or using this heater. heater circuit at main disconnect 2. This heater is hot when in use. panel. To avoid burns, do not let bare skin touch hot surfaces. Keep 7.
INSTALLATION INSTRUCTIONS ® 1. All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes. Canadian installations must comply with Codes Canada and provincial codes. 2. Use copper conductors only. 3. DO NOT install the heater directly above bathtub or sink. DO NOT install in shower stall area. Cadet recommends installing your heater at least 2 feet (61 cm) away to prevent contact with water. 4.
¾" (1.9 cm) Min. 4 PARED ADYACENTE INSTALLATION INSTRUCTIONS TIPS BEFORE YOU BEGIN • Verify power has been turned off before starting any work! • The Com-Pak Bath can only be mounted with the element up. It cannot be mounted in the ceiling or in the floor. For multiple heater wiring, see page 6. The Com-Pak Bath has a minimum clearance of 24" (61 cm) from the ceiling. • For cleaner performance and longer heater life, install your heater 12 inches (30.5 cm) from the floor.
INSTALLATION INSTRUCTIONS HOW TO CHANGE VOLTS (MULTI-VOLT MODEL CB103T ONLY) Check supply voltage C A Before installing your heater, it is extremely important you verify your supply voltage. The multi-volt Com-Pak Bath is 240 volts right out of the box. For 120 volts, you must change the heater wiring slightly. If you're replacing an existing heater, check the label of the old heater and use the same voltage. If you need help, review the "KNOW YOUR VOLTAGE" section, or call a licensed electrician.
INSTALLATION INSTRUCTIONS INSERT THE HEATER ASSEMBLY IN THE WALL CAN For 120 volts (CB103T only), connect the neutral (white) supply wire to the black and white striped wire (Figure 9).This wire is only on CB103T models. C. Connect the remaining supply wire to the remaining B heater wire with a wire connector (not included) (See Figures 8 and 9). 2. Insert the bottom edge of the heater assembly into the D-shaped tabs at the bottom of the wall can. 3.
OPERATING INSTRUCTIONS 1. Make sure all wires are properly connected and installation is complete before you turn on the heater. 2. Do not operate without grill. 3. Do not tamper with the hightemperature safety shutoff. Complete installation After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking may occur as the element initially burns off residue from manufacturing.
MAINTAINING YOUR HEATER lean heater at least every 6 months or as required. Do not lubricate motor. C WARNING – Risk of electrical shock, turn off power before removing grill. 1. Turn off power at the main disconnect panel. 2. Wait for the heater to cool. 3. Remove knobs and grill. 4. Wash grill with hot soapy water and dry. 5. Blow air through the heating element with a hair dryer or shop vacuum on blow cycle. 6. Clean the fan with a vacuum cleaner. 7. Replace grill and knobs. 8.
