Installation Guide

ManualsBrandsCadet Heaters ManualsAccessoriesCadet Baseboard Integral Load Transfer Switch Kit from the Cadet F Series

Warranty

Installation Instructions

1. Verify that the LTF-240 receptacle configuration (See Figure 1)

matches the appliance plug.

2. LTF must be installed at end of baseboard that carries the

incoming power supply.

3. Detach the baseboard junction box cover by removing the

retaining screw at the end where the load transfer switch will

be installed. Save the retaining screw for use in step 8.

4. Connect the 240 VAC incoming power supply wires to the

leads marked “line” on the switch (See Figure 2).

5. Connect the heater element leads to the LTF leads marked

“heater” (See Figure 2).

6. Connect the three ground wires together.

7. Check that no bare wire is exposed and that all wire

connections are tight.

8. CAUTION: Be certain the ground wires do not come in

contact with the terminal connections of the switch or outlet.

Attach the LTF plate to the heater using the screw that was

set aside.

9. Turn on the power to the heater.

NOTES

•

A single pole Cadet brand BTF1 thermostat must be

installed at the other end of the baseboard.

•

NOT intended for use with wall thermostat

•

Will not support double pole thermostat

HEATER OUTLET

Figure 1

LINE

GROUND

HEATER

SWITCH

LTF-240

20 AMP, 240V, 60 HZ

USE ONLY ON 20 AMP, BRANCH CIRCUIT

FOR USE WITH MODEL F

UL LISTED BASEBOARD ACCESSORY 631J

RECEPTACLE

Figure 2

WARRANTY

Warranties are non transferable and apply to original consumer

only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace

any Cadet product, including thermostats, found to be defective

within one year after the date of purchase.

THESE WARRANTIES DO NOT APPLY:

1. Damage occurs to the product through improper installation

or incorrect supply voltage;

2. Damage occurs to the product through improper maintenance,

misuse, abuse, accident, or alteration;

3. The product is serviced by anyone other than Cadet.

4. If the date of manufacture of the product cannot be determined;

5. If the product is damaged during shipping through no fault

of Cadet.

6. C A DET ’ S WARRAN T Y I S LIM ITED TO RE PAIR O R

REPLACEMENT AS SET OUT HEREIN. CADET SHALL NOT

BE LIA BLE FOR DAM A GES SUCH AS PROP ERTY

DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR

INCIDENTAL EXPENSES RESULTING FROM BREACH OF

THESE WRITTEN WARRANTIES OR ANY EXPRESS OR

IMPLIED WARRANTY.

7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART

OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS

ARE SUBJECT TO THE SAME WARRANTIES AS THE

PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS

DOES NOT MODIFY OR EXTEND THE UNDERLYING

WA RRA NTI ES. R EPL ACE MEN T O R REPA IR OF A NY

CADET PRODUCT OR PART DOES NOT CREATE ANY

NEW WARRANTIES.

8. These warranties give you specific legal rights, and you may

also have other rights which vary from state to state. Cadet

neither assumes, nor authorizes anyone to assume for it, any

other obligation or liability in connection with its products

other than as set out herein.

If you believe your Cadet product is defective, please,

contact Cadet at 360-693-2505, during the warranty period,

for instructions on how to have the repair or replacement

processed. Warranty claims made after the warranty period

has expired will be denied. Products returned without

authorization will be refused.

Parts and Service

Visit cadetheat.com/support/parts-service for information on

where to obtain parts and service.

Operating Instructions

Use the rocker switch to direct power to the baseboard heater OR the 240 volt outlet (See Figure 1).

ROCKER

SWITCH