Installation Guide

ManualsBrandsCadet ManualsHeater AccessoriesCom-Pak Surface Mount Wall Can in Almond

ATTACH HEATER

ASSEMBLY HERE

VERTICAL MOUNT:

MODELS CE(F),

CS(F), and CM

HORIZONTAL MOUNT:

MODELS CS(F), and

HAUT

Vancouver, WA cadetheat.com

*Model CS(F)

may be installed in the ceiling (1500

watts or less). Supply connections for ceiling-insert

installation shall use wires suitable for at least 167

° F

(75 ° C).

SURFACE MOUNT WALL CAN MODEL CCSM

070396B

CE(F):

Vertical

mount

only

CS(F)

& CM:

Vertical or

horizontal

mount

ALL

FIELD WIRING OUTSIDE

THESE LINES

HW:

Hori-

zontal

mount

only

.snoitcurtsni noitallatsni etelpmoc rof ediuG s’renwO ledom ruoy eeS

HAUT

MODEL

Minimum mounting clearances to:

Dégagements minimums de montage aux

Floor

surfaces

Surfaces du

plancher

Adjacent

walls

Murs contigus

Ceiling

Plafond

CE(F)4½"

(11.4 cm) 0" (0 cm) 10" (25.4 cm)

CS(F)4½" (11.4 cm) 0" (0 cm)

10" (25.4

cm)

CM 4½" (11.4 cm) 6" (15.2 cm) 10" (25.4 cm)

HW 72" (1.8 m) 6" (15.2 cm) 10" (25.4 cm)

Use copper conductors only

N’utilisez que des conducteurs en cuivre

For ceiling-insert installation, do not install

closer than 6 inches (15.2 cm) to any wall.

Si installer dans le plafond, maintenir plus de 6 po

(15.2 cm) d’aucun mu

HAUT

TOUT CÂBLAGE DE TERRAIN HORS DE CES LIGNES

HORIZONTAL MOUNT:

MODEL HW

THIS HOLE IS UNUSED

FOR MODEL HW

ATTACH HEATER

ASSEMBLY HERE

ATTACH GRILL HERE

ATTACH HEATER

ASSEMBLY HERE

ATTACH GRILL HERE

HAUT

Vancouver, WA cadetheat.com

*Model CS(F) may be installed in the ceiling (1500

watts or less). Supply connections for ceiling-insert

installation shall use wires suitable for at least 167 ° F

(75 ° C).

SURFACE MOUNT WALL CAN MODEL CCSM

070396B

CE(F):

Vertical

mount

only

CS(F)

& CM:

Vertical or

horizontal

mount

ALL FIELD WIRING OUTSIDE THESE LINES

HW:

Hori-

zontal

mount

only

.snoitcurtsni noitallatsni etelpmoc rof ediuG s’renwO ledom ruoy eeS

HAUT

MODEL

Minimum mounting clearances to:

Dégagements minimums de montage aux:

Floor

surfaces

Surfaces du

plancher

Adjacent

walls

Murs contigus

Ceiling

Plafond

CE(F)4½"

(11.4 cm) 0" (0 cm) 10" (25.4 cm)

CS(F)4½" (11.4 cm) 0" (0 cm)

10" (25.4

cm)

CM 4½"

(11.4 cm)

(15.2 cm)

10"

(25.4 cm)

HW 72" (1.8 m) 6" (15.2 cm) 10" (25.4 cm)

Use copper conductors only.

N’utilisez que des conducteurs en cuivre.

*For ceiling-insert installation, do not install

closer than 6 inches (15.2 cm) to any wall.

*Si installer dans le plafond, maintenir plus de 6 po

(15.2 cm) d’aucun mur.

HAUT

TOUT CÂBLAGE DE TERRAIN HORS DE CES LIGNES

cadetheat.com Tel: 855.CADET.US PO Box 1675 Vancouver, WA 98668-1675

SAVE THESE INSTRUCTIONS

CCSM Surface Mount

Wall Can

Installation Guide

Installation Instructions

Important Instructions

Warranty

TOOLS REQUIRED:

• Phillips Screwdriver

• Straight Screwdriver

• Wire Strippers

• Drill and Drill bits

• (4) Wall Fasteners

• Insulated Wire Connectors

• Conduit Connector

• Strain Relief Connector

Use with any Cadet model HW, CE(F), CS(F), or CM heater

Install heater assembly and grill or decorative cover kit according to the installation instructions included in your original product

Owner’s Guide.

WARNING

When using electrical appliances, basic precautions should always be followed to reduce the risk of re, electric shock, and injury to

persons. If you are uncomfortable working with electrical appliances, unable to follow these guidelines, or do not have the necessary

equipment; consult a licensed electrician. All steps must be followed.

NOTE: Before mounting the surface wall can, please read your original product Owner’s Guide or go to cadetheat.com for your heater’s

minimum placement clearances.

STEP 3

Install Heater Assembly and Grill

Feed supply wires through a conduit connector (not included),

leaving 14 inches of wire. Remove a knockout in the surface wall

can closest to the supply wires. Install a strain relief connector

(not included) in the surface wall can knockout. Feed supply wires

through the strain relief connector in the surface wall can and

secure them. Connect supply ground wire to grounding screw.

NOTE: All wiring outside of the surface wall can must be protected

by conduit or other approved devices.

STEP 2

Route Supply Wires

STEP 1

Mount the Surface Wall Can

Review the surface wall can label for correct direction (as noted

by the UP arrows) before mounting. In the vertical mounting po-

sition the element of the heater assembly will be at the top. In the

horizontal mounting position the element of the heater assembly

will be to the left.

Mount the surface wall can securely to the wall, using appropriate

wall fasteners (not included). Refer to your original product Own-

er’s Guide for minimum heater clearances from oor, adjacent

walls and ceiling.

PROVIDED:

• (1) Grounding Screw

• (1) Mounting Screw

For more effective and safer operation and to prolong the life of the heater, read the Own-

er’s Guide and follow the maintenance instructions. Failure to properly maintain the heater

will void any warranty and may cause the heater to function improperly. Warranties are non

transferable and apply to original consumer only. Warranty terms are set out below.

LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace any CADET product,

including thermostats, found to be defective within one year after the date of purchase.

These warranties do not apply:

1. Damage occurs to the product through improper installation or incorrect supply voltage;

2. Damage occurs to the product through improper maintenance, misuse, abuse, accident,

or alteration;

3. The product is serviced by anyone other than Cadet;

4. If the date of manufacture of the product cannot be determined;

5. If the product is damaged during shipping through no fault of Cadet.

6. The use of unauthorized accessories or unauthorized components constitutes an

alteration and voids all warranties. Refer to Cadet website or call customer service at 855.

CADET.US for list of authorized accessories and components.

7. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET OUT

HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROPERTY

DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EXPENSES

RESULTING FROM BREACH OF THESE WRITTEN WARRANTIES OR ANY EXPRESS

OR IMPLIED WARRANTY.

8. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET PROD-

UCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WARRANTIES AS

THE PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS DOES NOT MODIFY

OR EXTEND THE UNDERLYING WARRANTIES. REPLACEMENT OR REPAIR OF ANY

CADET PRODUCT OR PART DOES NOT CREATE ANY NEW WARRANTIES.

9. These warranties give you specic legal rights, and you may also have other rights

which vary from state to state. Cadet neither assumes, nor authorizes anyone to assume

for it, any other obligation or liability in connection with its products other than as set out

herein.

If you believe your Cadet product is defective, please contact Cadet Manufacturing Co. at

855.CADET.US, during the warranty period, for instructions on how to have the repair or

replacement processed. Warranty claims made after the warranty period has expired will

be denied. Products returned without authorization will be refused.

Parts and Service

Visit cadetheat.com/parts-service for information on where to obtain parts and service.

Reduce-Reuse-Recycle

This product is made primarily of recyclable materials. You can reduce your

carbon footprint by recycling this product at the end of its useful life. Contact

your local recycling support center for further recycling instructions.

http://cadetheat.com/products/wall-heaters

Information is also available on our website: