Installation & Assembly

ManualsBrandsCadet ManualsCooling & Air QualityCom-Pak Plus Series Electric Fan Wall Mounted Heater

cadetheat.com

855.CADET.US

Vancouver, Washington

tested to UL standards

OWNER’S GUIDE

ESPAÑOL ver la guía del propietario en cadetheat.com/espanol/com-pak

For how-to videos or more information, please visit:

http://cadetheat.com/install/com-pak

Thank you for your purchase! Question or problem? Let us solve it with a

single phone call, email or online chat! We’ll save you a trip back to the store!

Phone: 855.CADET.US (855.223.3887)

email: customerservice@cadetheat.com

Live chat: cadetheat.com (contact us)

Cadet Customer Service

COM-PAK

PERFECTLY SIMPLE WARMTH

FOR ANY ROOM

COM-PAK TWIN

IDEAL WARMTH

FOR LARGER AREAS

Summary of content (8 pages)

PAGE 1
OWNER’S GUIDE COM-PAK PERFECTLY SIMPLE WARMTH FOR ANY ROOM COM-PAK TWIN IDEAL WARMTH FOR LARGER AREAS Thank you for your purchase! Question or problem? Let us solve it with a single phone call, email or online chat! We’ll save you a trip back to the store! Cadet Customer Service Phone: 855.CADET.US (855.223.3887) email: customerservice@cadetheat.com Live chat: cadetheat.com (contact us) For how-to videos or more information, please visit: http://cadetheat.
PAGE 2
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before in- 6. To disconnect heater, turn control(s) to off, and turn off power to stalling or using this heater. 2. This heater is hot when in use. heater circuit at main disconnect To avoid burns, do not let bare skin panel. touch hot surfaces. Keep combusti- 7.
PAGE 3
INSTALLATION INSTRUCTIONS ® 1. All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes. 2. Use copper conductors only. 3. DO NOT install the heater directly above bathtub or sink. DO NOT install in shower stall area. Cadet recommends installing your heater at least 2 feet (61 cm) away to prevent contact with water. 4.
PAGE 4
¾" (1.9 cm) Min. PARED ADYACENTE INSTALLATION INSTRUCTIONS TIPS BEFORE YOU BEGIN • Verify power has been turned off before starting any work! • The Com-Pak model CS can be mounted with the element up, or with the element on the left. For ceiling installation, see page 5. For multiple heater wiring, see page 6. • The Com-Pak Twin model CST can only be mounted with the elements up. It cannot be mounted in the ceiling.
PAGE 5
INSTALLATION INSTRUCTIONS INSERT THE HEATER ASSEMBLY IN THE WALL CAN STEP 4 Wire connections 1. Your heater has two connection wires on the back. Your supply wire has two connection wires and a supply ground wire. A. Connect supply ground wire to grounding screw in wall can (See Figure 4 or 5). B. Connect one supply wire to one heater wire with a wire connector (not included): For 240 or 208 volts, it doesn’t matter which heater wire. Both supply wires (black and white) are hot.
PAGE 6
INSTALLATION INSTRUCTIONS MULTIPLE HEATERS WITH ONE THERMOSTAT (MODEL CS ONLY) More than one heater can be wired in parallel on the same circuit breaker (be sure to check national and local codes for safety requirements). Additional electrical supply wire and cable clamp connectors are required, and you’ll need to use a wall thermostat. When wiring multiple heaters to one thermostat, the heaters must be in the same room and be spaced a minimum of three feet apart.
PAGE 7
OPERATING INSTRUCTIONS 1. Make sure all wires are properly connected and installation is complete before you turn on the heater. 2. Do not operate without grill. 3. Do not tamper with the hightemperature safety shutoff. Complete installation After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking may occur as the element initially burns off residue from manufacturing.
PAGE 8
High-temperature safety shutoff All Com-Pak heaters come with built-in high-temperature safety shutoffs that stop electricity flowing to the heater if it gets too hot inside. See TROUBLESHOOTING below if you’re experiencing problems with your heater. TROUBLESHOOTING Symptom Problem Heater 1. Supply connections doesn’t work are loose. at all. 2. Heater has tripped one of its high-temperature safety shutoffs. 3. Heater has tripped its secondary high-temperature safety shutoff. 4.