Cadi.Sense Wireless Thermometer User Manual v3.21.3 T-S1-800.
Cadi.Sense User Manual Contents Introduction ........................................................................................................................ 3 1. 1.1 Welcome message ........................................................................................................... 3 1.2 User manual version.......................................................................................................... 3 1.3 Important safety information .......................................
Cadi.Sense User Manual 1. Introduction 1.1 Welcome message Thank you for choosing the Cadi.Sense Wireless Thermometer. This thermometer allows you to monitor your loved ones’ temperature without disturbing their rest and play. Read this manual carefully and follow all instructions and warnings. 1.2 User manual version 1.3 Version: C01 Release date: November 19, 2012 This user manual is subject to change or upgrade without notice. To view the latest user manual, go to www.cadisense.com.
Cadi.Sense User Manual 1.4 Intended use The Cadi.Sense wireless thermometer is intended for use in children for monitoring body temperature continuously and automatically. 1.5 Package contents ThermoSensor (with storage case) SmartNode (plug) T-S1-800.
Cadi.Sense User Manual 1.6 Stick-Ons (adhesive dressing) How does the Cadi.Sense work? In the Cadi.Sense, skin temperature is measured at the lower abdomen by a wireless sensor called the ThermoSensor. The readings are sent wirelessly every 30 seconds to a receiver called the SmartNode and converted to an equivalent body temperature, which can be viewed via WiFi from a mobile device such as a smartphone. 1.
Cadi.Sense User Manual 2. How to set up and use the Cadi.Sense 2.1 Overview Before using the Cadi.Sense, you will need to do the following: 1. Set up the system for wireless access, by following the instructions in Sections 2.2, 2.3, 2.4, and 2.5. 2. Understand the LED indicators and Cadi.Sense icons, by reading Sections 2.6 and 2.7 respectively. 3. Know how to attach the ThermoSensor to the patient, by following the instructions in Section 2.8. 4.
Cadi.Sense User Manual Figure 1. Setting date, time, and timezone. Figure 2. Main page (sensor details). Figure 3. Home page (temperature monitoring). Note: After you have set the date, time, and timezone, Figure 2 will appear. The sensor ID will be shown and the temperature will be displayed as “--” or “Lo”. If the sensor is still in its storage case, the reading will be displayed as “--”.
Cadi.Sense User Manual Figure 4. Advanced settings menu. Figure 5. Connecting to your WiFi router. Figure 6. Successful connection. If the connection is successful, the following text will appear: “SmartNode is now connected to xxxxxx. To access SmartNode, please go to www.cadisense.com or use the LAN URL. Please be patient as SmartNode needs about a minute to reboot.” Figure 6 will then appear.
Cadi.Sense User Manual Figure 7. Cadi.Sense page without UPnP/port forwarding setup. Figure 8. Cadi.Sense page with UPnP/port forwarding setup. 2.4 Setup III (Advanced) – Performing port forwarding to access your SmartNode from outside your home This setup enables you to view your SmartNode webpages from outside your home via the Internet. Note: You do not need to perform this setup if you have been able to see Figure 8 in the previous setup. Note: This section is for advanced users only.
Cadi.Sense User Manual Gateway: (this is the LAN IP address of your WiFi router) Step 2: Go to your mobile device’s web browser, enter the LAN IP address of your WiFi router, and then type in your WiFi router’s admin password, if any. Step 3: Find the UPnP setting and enable it. (Note: Some routers may not have this feature.) You may have to reboot your WiFi router for the setting to take effect (check your WiFi router’s manual).
Cadi.Sense User Manual Step 2: On the home tab, select your child, click another “+” sign, and select “Cadi.Sense Monitoring”. Type in some notes in the Description field for your own reference and also type in your 8-digit sensor ID (serial number) in the Sensor field (the sensor ID can be found on the ThermoSensor). Step 3: Select the monitoring tab and you are done! 2.6 Understanding the SmartNode LEDs Power LED: lights up when power is on.
Cadi.Sense User Manual 2.7 Understanding the Cadi.Sense icons on your SmartNode webpages Go to home page (temperature monitoring page): View a single sensor temperature in large font size. Refresh: Manually refresh the current page to get the latest temperature. The page will actually refresh automatically every 5 minutes. Advanced settings: View a list of all advanced settings, including connecting to your WiFi router. Set timezone, date & time: Manually set the timezone, date, and time if necessary.
Cadi.Sense User Manual Click these icons and you will see the following screens: Main page (sensor details) Home page (temperature monitoring) Advanced settings menu Setting date, time, and timezone Add sensor (by entering sensor ID) Remove sensor (by clicking inside the red box) T-S1-800.
Cadi.Sense User Manual Temperature chart 2.8 Temperature history Sensor settings (name, alert, °C or °F, temperature threshold) How to attach the ThermoSensor Step 1: Apply a small amount of body lotion on the left or right side of the lower abdomen. Step 2: Take a Stick-On and peel off the round paper liner to expose the adhesive. Step 3: Stick the ThermoSensor on the adhesive, with the metal part facing outward and away from the adhesive. T-S1-800.
Cadi.Sense User Manual Step 4: Remove the rectangular backing liner to expose the adhesive. Step 5: Stick the exposed adhesive to the inside of the diaper/undergarment in such a position that the sensor's metal part will touch the lower abdomen (left or right) when the diaper/undergarment is properly worn. Note: For accurate temperature readings, the sensor must touch the left or right side of the lower abdomen at all times during monitoring. T-S1-800.
Cadi.Sense User Manual The ThermoSensor may take about 30 minutes to warm up from room temperature to body temperature. A temperature reading is sent wirelessly every 30 seconds to your SmartNode, and this reading will be converted into an equivalent body temperature, which will appear on your mobile device or computer. 2.9 How to clean and store the ThermoSensor and the SmartNode Step 1: After each use, peel the Stick-On off the diaper/undergarment and then peel the StickOn off the sensor.
Cadi.Sense User Manual Step 3: Clean the SmartNode with a soft cloth moistened with alcohol. Step 4: Place both the SmartNode and the ThermoSensor with its storage case in the original package, and store the package in a cool, dry place and keep it out of reach of babies and young children. Note: When the SmartNode is not being used for temperature monitoring, you may wish to use it as a wireless extender. See Section 4.6 (“More about the SmartNode”) for more details. 3. Advanced features 3.
Cadi.Sense User Manual 3.2 Resetting the SmartNode Warning: All data will be deleted after this hardware reset. Therefore, before resetting, you may want to export the data using the “Export temperature history data” icon that will be available only from your laptop’s web browser. Step 1: Make sure the SmartNode is switched on for at least 1 minute. Take a paperclip and bend the tip outwards.
Cadi.Sense User Manual Step 4: Reset the SmartNode (this is important!), by following the instructions in Section 3.2 or those on the webpage from which you downloaded the firmware. Step 5: Reboot the SmartNode by switching it off and on again. The reboot will take about 1 minute. Step 6: Remove the LAN cable. 4. Others 4.1 Troubleshooting and frequently asked questions (FAQ) Concerning the ThermoSensor 1.
Cadi.Sense User Manual If the above instructions do not answer your concerns, please contact Technical Support for assistance. Concerning the Cadi.Sense software application 4. I am unable to log in to http://www.cadisense.com. Why? Make sure you are connected to the Internet. Try to access other websites (e.g., www.google.com) to check your Internet connection. 5. Why is there no current temperature on the Cadi.
Cadi.Sense User Manual EC REP Complies with IDA Standards DB 10249 Medical Device Safety Service GmbH Schiffgraben 41 30175 Hannover, Germany CADI SCENTIFIC PTE LTD 31 Ubi Road 1 #03-00 Aztech Building Singapore 408694 www.cadi.com.sg Note: The stick-on dressing is supplied by Shanghai Huyou Medical Electrode Ltd, 45 Lane 1398, Zhenchen Road, Baoshan, 200435 Shanghai, China. 4.4 Specifications ThermoSensor specifications Temperature Measuring range 32.0 ºC to 42.0 ºC Out-of-range indications <32.
Cadi.Sense User Manual SmartNode specifications Radio Radio frequency (short range device) 868.4 MHz , 919.8 MHz, or 925 MHz, depending on countries WLAN WiFi 802.11b/g/n Interface Ethernet 1 x 10/100 Auto MDI/MDIX Ethernet Port Power Input voltage 100–240 VAC, 50–60 Hz Maximum current: 0.
Cadi.Sense User Manual 4.5 More about port forwarding Port forwarding screens for the following WiFi routers are shown below: 1. Aztech DSL1015EW(S) or DSL1000ER 2. 2WIRE 5012NV T-S1-800.
Cadi.Sense User Manual 3. 2WIRE 2701HGV-E 4. Linksys E2000 T-S1-800.
Cadi.Sense User Manual 5. Dlink DIR 655 6. ZyXel T-S1-800.
Cadi.Sense User Manual 7. ASUS-RTN16 8. EnGenius ESR9850 T-S1-800.
Cadi.Sense User Manual 4.6 More about the SmartNode The SmartNode supports wireless 802.11b/g/n standards with one 10/100Base-T Ethernet port. It is designed with MIMO technology to extend the reach of any existing wireless router/AP to maximize the coverage in your home or office. It basically receives the signal from your wireless router/AP and repeats it to extend the range to farther locations that are previously unreachable.
Cadi.Sense User Manual Click the “Connect to WiFi Router” icon. When a screen appears and asks “Please select your WiFi router”, click your router’s SSID, type in your router’s password, and then click “Apply”. Be patient as the SmartNode needs about 1 minute to connect to your WiFi router and about one minute to reboot. Click “Refresh” if you do not see your router’s SSID on the list.
Cadi.Sense User Manual To configure the SmartNode for use as a WiFi AP: Plug in the SmartNode to a power socket and switch it on. (Note: The SmartNode takes about 30 seconds to start up.) Connect the SmartNode to your modem-router using an Ethernet cable. You are now ready to access internet on your laptops and smartphones via WiFi.
Cadi.Sense User Manual T-S1-800.
Cadi.Sense User Manual Using WPS (WiFi Protected Setup) WPS is an alternative and easier way to connect the SmartNode to your WiFi router or a wireless client. To connect the SmartNode to your WiFi router/AP via WPS: Press the WPS button on the SmartNode for 5 seconds to activate WPS Enrollee mode. Press the WPS button on your WiFi router/AP within 2 minutes. The 2 devices should then associate with each other automatically within 2 minutes.
Cadi.Sense User Manual Reboot Reboot allows you to reboot the device for new settings to take effect. Device settings Device Settings includes the following options: Device information IP address (LAN configuration) Settings backup (configuration settings) T-S1-800.
Cadi.Sense User Manual Firmware upgrade Password (system password) Device information This page shows the device information. Below is the list of information shown in this menu.
Cadi.Sense User Manual Settings backup (configuration settings) This page allows you to back up and restore the current device configuration, as well as to reset the device to its factory default settings.
Cadi.Sense User Manual Password (system password) The password menu allows you to change the device’s password to access SmartNode webpages. Setting a static IP on your PC The SmartNode will only give an IP address to your PC upon initial installation. Once you have associated the SmartNode with your WiFi router/AP, you may no longer have access to the device’s webpages.
Cadi.Sense User Manual Click to select Internet Protocol Version 4 (TCP/Ipv4) (“TCP/IP” for Windows XP), and then click “Properties”. Select “Use the following IP address:” and type in “10.10.10.20” as the IP address and “255.255.255.0” for the subnet mask. Leave the other fields blank. Click “OK” to commit the settings. Note: Please remember to revert to “Obtain an IP address automatically” on your PC after you are done with changes to the SmartNode. T-S1-800.
