Installation Sheet Cadillac CTS 2008-2011 In-Car Router Installation Kit Contents: Item 1 Description Power Cable Qty. 1 2 3 4 5 6 7 8 9 10 11 Nylon Key-Hole Clip Red Posi-Tap Connector Black Posi-Tap Connector 8" Nylon Cable tie 2.8 terminal 1.5 terminal M6 Nut Dampening Tape CTS Router Label Window Decal 4 1 1 4 1 1 1 1 1 1 Installation Procedure: 1. On left wall of trunk, remove the three fasteners that secure the trunk liner. 225-1100-01 V1.
1 Installation Sheet 2. Remove Velcro attached net storage if equipped. 3. Open left rear passenger door fold down seat and remove two remaining fasteners that secure trunk liner. 4. Remove trunk liner. 225-1100-01 V1.5 Cadillac CTS Installation Sheet Autonet Mobile Customer Service – 1-800-977-2107 or support@autonetmobile.
1 Installation Sheet 5. Using Router Docking Station as a template, drill or punch four 1/8” diameter holes in level area near rear of trunk liner. Use cautioninsulation located behind this area can bind in drill bit. 6. Attach docking station using four supplied nylon Key Hole clips. 7. Drill a 3/8” hole directly below docking station for power wire. 8. Run power wire through hole in trunk liner. Secure in place with grommet. 225-1100-01 V1.
1 Installation Sheet 9. Attach black lead of supplied power cable to ground stub on rear wheel well of trunk using supplied nut. 10. Feed cable through seat frame into passenger cabin. 11. Run power cable under trim to left instrument panel access area on the driver’s side of dash. 225-1100-01 V1.5 Cadillac CTS Installation Sheet Autonet Mobile Customer Service – 1-800-977-2107 or support@autonetmobile.
1 Installation Sheet 12. Open left instrument power access area. 13. Locate and unplug 14 pin harness 225-1100-01 V1.5 Cadillac CTS Installation Sheet Autonet Mobile Customer Service – 1-800-977-2107 or support@autonetmobile.
1 Installation Sheet 14. Using the Table below, determine which wire to tap. Table 1-1 Model Year Wire/ Pin location Instructions 2008-2009 Pink Wire on Pin 1 2010 Pink Wire on Pin 13 2011+ Pink Wire on Pin 1 2008-2009 No Pink Wire on Pin 1 2010 No Pink Wire on Pin 13 2011+ No Pink Wire on Pin 1 Use the Red PosiTap connector and go to step 15 Use the Red PosiTap connector and go to step 15 Use the Black Posi-Tap connector and go to step 15 Go to step 22 and use the 2.
1 Installation Sheet 16. Screw tap pin onto cap and observe that tap is centered on wire. Thread by hand until wire is tightly tapped. 17. Strip 1/8” from end of power cable 18. Unscrew splice cap from bottom of Posi-tap connector and insert wire. 19. Brush exposed wire strands with thumbnail and insert wire strands into one side of the metal core. 225-1100-01 V1.5 Cadillac CTS Installation Sheet Autonet Mobile Customer Service – 1-800-977-2107 or support@autonetmobile.
1 Installation Sheet 20. Push and turn until threads catch, then screw in tightly by hand. Ensure a good splice by verifying that wire will not slip back through cap. 21. Posi-tap installation complete, go to step 25 22. If there is no pink wire on Pin 1 or 13 of connector, strip 1/8” from end of the supplied red power lead. 23. Crimp the correct terminal (see table 1-1) onto end of lead. 24. Insert pin and lead into correct receptacle in connector (see table 1-1) 225-1100-01 V1.
1 Installation Sheet 25. Reconnect 14 Pin harness 26. Using supplied cable ties, secure power lead in such a way to prevent any vibration noise. 27. If Posi-tap connector was installed, use supplied vibration dampening tape to shield connector from access cover. 28. Replace access cover. 29. In trunk, connect router docking station cable to installed power cable. 30. Using supplied cable ties, secure power cable is such a way to prevent any vibration noise. 31. Replace trunk liner 32.
1 Installation Sheet 34. Installation complete, the Autonet Mobile InCar Router is ready to test. 35. Happy Surfing! 36. Place the CTS Router Label on the router as shown. 37. Place the window decal on the driver’s side rear quarter window. 225-1100-01 V1.5 Cadillac CTS Installation Sheet Autonet Mobile Customer Service – 1-800-977-2107 or support@autonetmobile.
1 Installation Sheet Safety Precautions WARNING To prevent injury or fire, take the following precautions: • To prevent a short circuit never put or leave any metallic objects (such as coins or metal tools) inside the unit. • If the unit starts to emit smoke or strange smells, disconnect immediately and consult the Autonet Mobile Customer Service Center. • Do not touch the In-Car Router during use because the surface of the unit becomes hot and may cause burns if touched.
1 Installation Sheet FCC WARNING Exposure to Radio Frequency Signals Autonet Mobile is a low power radio transmitter and receiver. When it is turned on, it sends out and receives RF signals. Autonet Mobile complies with FCC guidelines respecting safe levels of RF exposure for handled wireless devices, which in turn are consistent with the following safety standards previously set by certain standards bodies: · • ANSI/IEEE C95.