Cadillac Escalade Hybrid - 2012 Black plate (1,1) 2012 Cadillac Escalade Hybrid M In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Initial Drive Information . . . . . . . . 1-1 Hybrid Features . . . . . . . . . . . . . . . 1-2 Performance and Maintenance . . . . . . . . . . . . . . . . . 1-5 Seats and Restraints . . . . . . . . . 3-1 Airbag System . . . . . . . . . . . . . . . . . 3-1 Storage . . . . . . . . . . . . . . . . . . . . . . . 4-1 Storage Compartments . . . . . . . .
Cadillac Escalade Hybrid - 2012 ii Black plate (2,1) Introduction The names, logos, emblems, slogans, vehicle model names, and vehicle body designs appearing in this manual including, but not limited to, GM, the GM logo, CADILLAC, the CADILLAC Crest and Wreath, and ESCALADE are trademarks and/or service marks of General Motors LLC, its subsidiaries, affiliates, or licensors. Keep this manual in the vehicle for quick reference.
Cadillac Escalade Hybrid - 2012 Black plate (1,1) In Brief In Brief Initial Drive Information Transmission . . . . . . . . . . . . . . . . . . 1-1 Four-Wheel Drive . . . . . . . . . . . . . 1-1 Initial Drive Information Transmission Range Selection Mode Hybrid Features High Voltage Safety Information . . . . . . . . . . . . . . . . . . 1-2 Fuel Economy Gauge . . . . . . . . . 1-3 Automatic Engine Start/Stop Feature . . . . . . . . . . . . . . . . . . . . . . 1-3 Regenerative Braking . . . . . . . . .
Cadillac Escalade Hybrid - 2012 1-2 Black plate (2,1) In Brief Automatic Transfer Case The transfer case knob is located to the left of the instrument panel cluster. You can choose among five driving settings: 2 m (Two-Wheel Drive High): This setting is used for driving in most street and highway situations. AUTO (Automatic Four-Wheel Drive): This setting is ideal for use when road surface traction conditions are variable.
Cadillac Escalade Hybrid - 2012 Black plate (3,1) In Brief Fuel Economy Gauge This gauge shows when the vehicle is operating at a fuel efficient point. Driving behavior that improves fuel efficiency makes the fuel indicator move to the high efficiency band on the fuel gauge. See Fuel Economy Gauge on page 5‑3 for more information. Automatic Engine Start/ Stop Feature Metric English Start the engine as you would any other engine.
Cadillac Escalade Hybrid - 2012 1-4 Black plate (4,1) In Brief A chime will sound if the driver door is opened while in Auto Stop as a reminder that the ignition switch is not in the LOCK/OFF position. Always turn the ignition switch to LOCK/OFF and remove the key from the ignition switch when exiting the vehicle. Auto Start The vehicle also has an Auto Start feature. The engine will remain off while in Auto Stop mode until vehicle conditions require the engine to run.
Cadillac Escalade Hybrid - 2012 Black plate (5,1) In Brief Battery Service This vehicle has a standard 12-volt battery and a high voltage hybrid battery. When a new standard 12-volt battery is needed, see your dealer for one that has the replacement number shown on the original battery's label. Only a trained service technician with the proper knowledge and tools should inspect, test, or replace the hybrid battery. See your dealer if the hybrid battery needs service. See Battery on page 10‑11.
Cadillac Escalade Hybrid - 2012 1-6 Black plate (6,1) In Brief 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Seats and Restraints Seats and Restraints Airbag System Airbag System If an airbag inflates or the vehicle has been in a crash, the vehicle's sensing system may command the automatic hybrid battery disconnect to open. When the battery disconnect is open, the hybrid battery will be off and the vehicle will not start. The airbag readiness light and/or SERVICE HYBRID SYSTEM warning message may come on in the Driver Information Center (DIC).
Cadillac Escalade Hybrid - 2012 3-2 Black plate (2,1) Seats and Restraints 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Storage Storage Storage Compartments Rear Storage . . . . . . . . . . . . . . . . . 4-1 Storage Compartments Rear Storage Power Outlet Alternating Current The vehicle may have a power outlet that can be used to plug in electrical equipment that uses a maximum limit of 150 watts. The power outlet is located in the rear cargo area on the driver side. 4-1 An indicator light on the outlet turns on to show it is in use.
Cadillac Escalade Hybrid - 2012 4-2 Storage The power outlet is not designed for the following electrical equipment and may not work properly if these items are plugged into the power outlet: . Equipment with high initial peak wattage such as: compressor-driven refrigerators and electric power tools. . Other equipment requiring an extremely stable power supply such as: microcomputer-controlled electric blankets, touch sensor lamps, etc. See High Voltage Devices and Wiring on page 10‑13.
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Instruments and Controls Instruments and Controls Vehicle Messages Warning Lights, Gauges, and Indicators Instrument Cluster . . . . . . . . . . . . Tachometer . . . . . . . . . . . . . . . . . . . Fuel Economy Gauge . . . . . . . . . Charging System Light . . . . . . . . Engine Oil Pressure Light . . . . . 5-2 5-3 5-3 5-4 5-4 Information Displays Driver Information Center (DIC) . . . . . . . . . . . . . . . . . 5-5 Vehicle Messages . . . . . . . . .
Cadillac Escalade Hybrid - 2012 5-2 Black plate (2,1) Instruments and Controls Warning Lights, Gauges, and Indicators Instrument Cluster English Version Shown, Metric Similar
Cadillac Escalade Hybrid - 2012 Black plate (3,1) Instruments and Controls Tachometer 5-3 The tachometer may vary by several hundred rpm's, during AUTO STOP mode, when the engine is shutting off and restarting. A slight bump may be felt when the transmission is determining the most fuel efficient operating range. Fuel Economy Gauge English This gauge is to assist in driving efficiently and may vary during normal operation.
Cadillac Escalade Hybrid - 2012 5-4 Black plate (4,1) Instruments and Controls Charging System Light short distance must be driven with the light on, be certain to turn off all the accessories. Engine Oil Pressure Light { WARNING This 12‐volt battery light comes on briefly when the ignition is turned to ON/RUN, but the engine is not running, as a check to show it is working. It should go out once the engine has been started.
Cadillac Escalade Hybrid - 2012 Black plate (5,1) Instruments and Controls Information Displays Vehicle Information Menu Items Driver Information Center (DIC) Press the vehicle information button to display the Vehicle Information Menu items. For more items see “Driver Information Center (DIC)” in the owner manual. Trip/Fuel Menu Items Press the trip/fuel button to display the Trip/Fuel Menu items. For more items see “Driver Information Center (DIC)” in the owner manual.
Cadillac Escalade Hybrid - 2012 5-6 Black plate (6,1) Instruments and Controls Battery Voltage and Charging Messages Brake System Messages Door Ajar Messages SERVICE BRAKE SYSTEM HOOD OPEN SERVICE BATTERY CHARGING SYSTEM This message may be displayed if there is a problem with the brake system. You will still be able to brake, but it will be noticeably more difficult. Pull off the road to a safe location and have your vehicle towed to the nearest dealer for service.
Cadillac Escalade Hybrid - 2012 Black plate (7,1) Instruments and Controls 5-7 Engine Oil Messages Service Vehicle Messages Transmission Messages OIL PRESSURE LOW STOP ENGINE SERVICE HYBRID SYSTEM SERVICE 4 WHEEL DRIVE If this message is displayed on the DIC, the vehicle may continue to operate, but you need to have it serviced as soon as possible. This message may display if a problem occurs with the four-wheel-drive system.
Cadillac Escalade Hybrid - 2012 5-8 Black plate (8,1) Instruments and Controls 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Infotainment System Infotainment System Introduction Infotainment . . . . . . . . . . . . . . . . . . . 7-1 Introduction Infotainment The vehicle has a navigation radio system. See the owner manual for more information. Press the CONFIG button on the radio to display the hybrid screen. The screen shows: . Auto Stop . Battery Charging . Engine Idle .
Cadillac Escalade Hybrid - 2012 7-2 Black plate (2,1) Infotainment System 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Climate Controls Climate Controls Climate Control Systems Climate Control Systems For more information on the vehicle's climate control system, see “Climate Control System” in the owner manual. Climate Control Systems . . . . . . 8-1 Electric Air Conditioning Compressor This hybrid vehicle has an electrically powered air conditioning compressor.
Cadillac Escalade Hybrid - 2012 8-2 Black plate (2,1) Climate Controls 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Driving and Operating Driving and Operating Automatic Transmission Automatic Transmission . . . . . . . 9-7 Manual Mode . . . . . . . . . . . . . . . . 9-10 Drive Systems Driving Information Steering . . . . . . . . . . . . . . . . . . . . . . . 9-1 Starting and Operating Starting the Vehicle . . . . . . . . . . . 9-2 Engine Coolant Heater . . . . . . . . 9-4 Shifting Into Park . . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 9-2 Black plate (2,1) Driving and Operating Starting and Operating Starting the Vehicle { WARNING Exiting the vehicle, without first shifting into P (Park), may cause the vehicle to move, and you or others can be seriously injured. Because the vehicle has the Automatic Engine Start/Stop feature, the vehicle’s engine might seem to be shut off when you come to a complete stop. However, once the brake pedal is released, the vehicle can move.
Cadillac Escalade Hybrid - 2012 Black plate (3,1) Driving and Operating When the tachometer needle indicates AUTO STOP, the hybrid system is on, the engine is not running, but may Auto Start at any time without notice. See Tachometer on page 5‑3 for more information. A chime will sound if the driver door is opened while in Auto Stop as a reminder that the ignition switch is not in the LOCK/OFF position.
Cadillac Escalade Hybrid - 2012 9-4 Black plate (4,1) Driving and Operating Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm-up in cold weather conditions at or below −18°C (0°F). Vehicles with an engine heater should be plugged in at least four hours before starting. An internal thermostat in the plug-end of the cord may exist which will prevent engine coolant heater operation at temperatures above −18°C (0°F).
Cadillac Escalade Hybrid - 2012 Black plate (5,1) Driving and Operating 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep it away from moving engine parts. If you do not, it could be damaged. The length of time the heater should remain plugged in depends on several factors. Ask a dealer in the area where you will be parking the vehicle for the best advice on this.
Cadillac Escalade Hybrid - 2012 9-6 Black plate (6,1) Driving and Operating Leaving the Vehicle with the Engine Running { WARNING It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. If you have four-wheel drive and the transfer case is in N (Neutral), the vehicle will be free to roll, even if the shift lever is in P (Park).
Cadillac Escalade Hybrid - 2012 Black plate (7,1) Driving and Operating Engine Exhaust Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. { WARNING Exiting the vehicle, without first shifting into P (Park), may cause the vehicle to move, and you or others can be seriously injured.
Cadillac Escalade Hybrid - 2012 9-8 Black plate (8,1) Driving and Operating When parked on a hill, especially when the vehicle has a heavy load, you may notice an increase in the effort to shift out of P (Park). See Shifting Into Park on page 9‑5. { WARNING It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to.
Cadillac Escalade Hybrid - 2012 Black plate (9,1) Driving and Operating Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle. D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: .
Cadillac Escalade Hybrid - 2012 9-10 Black plate (10,1) Driving and Operating Manual Mode Range Selection Mode The Range Selection Mode controls the vehicle's transmission. To use this feature: 1. Move the shift lever to the M (Manual Mode). 2. Press the plus/minus button to upshift or downshift selecting the desired range of gears. A number displays next to the M, indicating the current gear that has been selected. The number displayed in the gear indicator is the highest gear that can be used.
Cadillac Escalade Hybrid - 2012 Black plate (11,1) Driving and Operating Four-Wheel Drive While driving on clean dry pavement and during tight turns, you may experience a vibration in the steering system. If the vehicle has four-wheel drive, you can send the engine's driving power to all four wheels for extra traction. Read the following before using four-wheel drive. The vehicle has StabiliTrak. Shifting into Four-Wheel Drive Low will turn Traction Control and StabiliTrak off.
Cadillac Escalade Hybrid - 2012 9-12 Black plate (12,1) Driving and Operating If the lights do not come on, you should take the vehicle to your dealer for service. An indicator light will flash while shifting. It will stay on when the shift is completed. If for some reason the transfer case cannot make a requested shift, it will return to the last chosen setting. 2 m (Two-Wheel Drive High): This setting is used for driving in most street and highway situations.
Cadillac Escalade Hybrid - 2012 Black plate (13,1) Driving and Operating Shifting Into Four-Wheel Drive High or AUTO (Automatic Four-Wheel Drive) high-speed operation in 4L may damage or shorten the life of the drivetrain. Turn the knob to the Four-Wheel High or AUTO position. This can be done at any speed, except when shifting from Four-Wheel Drive Low. The indicator light will flash while shifting. It will remain on when the shift is completed.
Cadillac Escalade Hybrid - 2012 9-14 Black plate (14,1) Driving and Operating The preferred method for shifting out of Four-Wheel Drive Low is to have your vehicle moving 1.6 to 3.2 km/h (1 to 2 mph). Turn the knob to the Four-Wheel Drive High, AUTO, or Two-Wheel Drive High position. You must wait for the Four-Wheel Drive High, AUTO, or Two-Wheel Drive High indicator light to stop flashing and remain on before shifting the transmission into gear.
Cadillac Escalade Hybrid - 2012 Black plate (15,1) Driving and Operating Shifting Out of Neutral To shift the transfer case out of N (Neutral): 1. Set the parking brake and apply the regular brake pedal. 2. Turn the ignition to ON/RUN with the engine off, and shift the transmission to N (Neutral). 3. Turn the transfer case dial to the desired transfer case shift position (Two-Wheel Drive High, Four-Wheel Drive High, AUTO).
Cadillac Escalade Hybrid - 2012 9-16 Black plate (16,1) Driving and Operating Because the controller applies the hydraulic brakes through its high pressure accumulator, you may occasionally hear the motor driven pump when it recharges the system. This is normal. Towing In the event of a controller problem, the brake pedal may be harder to push and the stopping distance may be longer. Weight of the Trailer Trailer Towing For more information, see “Towing a Trailer” in the owner manual.
Cadillac Escalade Hybrid - 2012 Black plate (17,1) Driving and Operating Vehicle 9-17 Axle Ratio Maximum Trailer Weight GCWR* 2WD 6.0L V8 3.08 2 631 kg (5,800 lbs) 5 443 kg (12,000 lbs) 4WD 6.0L V8 3.08 2 540 kg (5,600 lbs) 5 443 kg (12,000 lbs) *The Gross Combination Weight Rating (GCWR) is the total allowable weight of the completely loaded vehicle and trailer including any passengers, cargo, equipment and conversions. The GCWR for the vehicle should not be exceeded.
Cadillac Escalade Hybrid - 2012 9-18 Black plate (18,1) Driving and Operating 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Vehicle Care Vehicle Care Vehicle Checks Doing Your Own Service Work . . . . . . . . . . . . . . . 10-2 Engine Compartment Overview . . . . . . . . . . . . . . . . . . . 10-4 Automatic Transmission Fluid . . . . . . . . . . . . . . . . . . . . . . . 10-5 Drive Motor/Generator Control Module (DMCM) Coolant Surge Tank Pressure Cap . . . . . . . . . . . . . . 10-8 Drive Motor/Generator Control Module (DMCM) Cooling System . . . . . . . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 10-2 Black plate (2,1) Vehicle Care Vehicle Checks Doing Your Own Service Work { WARNING Never try to do your own service on hybrid components. You can be injured and the vehicle can be damaged if you try to do your own service work. Service and repair of these hybrid components should only be performed by a trained service technician with the proper knowledge and tools.
Cadillac Escalade Hybrid - 2012 Black plate (3,1) Vehicle Care 2 NOTES 10-3
Cadillac Escalade Hybrid - 2012 10-4 Black plate (4,1) Vehicle Care Engine Compartment Overview 6.
Cadillac Escalade Hybrid - 2012 Black plate (5,1) Vehicle Care A. See “Engine Air Cleaner/Filter” in the owner manual. B. Drive Motor/Generator Control Module (DMCM). See Drive Motor/Generator Control Module (DMCM) Cooling System on page 10‑8. C. Engine Oil Dipstick (Out of View). See “Engine Oil” in the owner manual. D. Automatic Transmission Fluid Dipstick. See Automatic Transmission Fluid on page 10‑5. E. Brake Fluid Reservoir. See “Brakes” in the owner manual. F.
Cadillac Escalade Hybrid - 2012 10-6 Black plate (6,1) Vehicle Care How to Check Automatic Transmission Fluid Notice: Too much or too little fluid can damage the transmission. Too much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. Too little fluid could cause the transmission to overheat. Be sure to get an accurate reading if checking the transmission fluid. Before checking the fluid level, prepare the vehicle as follows: 1.
Cadillac Escalade Hybrid - 2012 Black plate (7,1) Vehicle Care See Engine Compartment Overview on page 10‑4 for more information. 2. Pull out the dipstick and wipe it with a clean rag or paper towel. 3. Install the dipstick by pushing it back in all the way, wait three seconds, and then pull it back out again. 4. Check both sides of the dipstick and read the lower level. Repeat the check procedure to verify the reading. 5.
Cadillac Escalade Hybrid - 2012 10-8 Black plate (8,1) Vehicle Care Consistency of Readings 5. Safe operating level is within the HOT cross hatch band on the dipstick. If the fluid level is not within the HOT band, and the transmission temperature is between 60°C and 75°C (140°F and 167°F), add or drain fluid as necessary to bring the level into the HOT band. If the fluid level is low, add only enough fluid to bring the level into the HOT band. It does not take much fluid, generally less than 0.
Cadillac Escalade Hybrid - 2012 Black plate (9,1) Vehicle Care “Engine Coolant” and “Cooling System” in the owner manual for more information. D. DMCM Cooling Hoses (Out of View) E. DMCM Coolant Surge Tank Pressure Cap If the coolant inside the DMCM coolant surge tank is boiling, do not do anything else until it cools down. When it is safe to lift the hood: A. Drive Motor/Generator Control Module (DMCM) B. Engine Coolant Surge Tank Pressure Cap C.
Cadillac Escalade Hybrid - 2012 10-10 Black plate (10,1) Vehicle Care How to Add Coolant to the DMCM Coolant Surge Tank If no problem has been found yet, check to see if coolant is visible in the DMCM coolant surge tank. If coolant is visible, add pre‐mixed DEX-COOL coolant, available at your dealer, at the DMCM coolant surge tank, but be sure the DMCM cooling system, including the DMCM coolant surge tank pressure cap, is cool before you do it. Use the procedure following.
Cadillac Escalade Hybrid - 2012 Black plate (11,1) Vehicle Care surge tank pressure cap and DMCM cooling hoses, are no longer hot. Turn the DMCM coolant surge tank pressure cap slowly counterclockwise (left) about one full turn. Wait 30 seconds. 4. Turn the ignition to ON/RUN without starting the engine. The hybrid cooling pumps will run and any trapped air will purge to the surge tank. 5. Add the pre‐mixed DEX‐COOL, available at your dealer, until the coolant level is maintained at the FULL COLD mark.
Cadillac Escalade Hybrid - 2012 10-12 Black plate (12,1) Vehicle Care If an airbag inflates or the vehicle has been in a crash, the vehicle's sensing system might command the automatic hybrid battery disconnect to open. See Replacing Airbag System Parts after a Crash on page 3‑1 for more information. { WARNING Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
Cadillac Escalade Hybrid - 2012 Black plate (13,1) Vehicle Care When to Change Lubricant See “Scheduled Maintenance” in the owner manual to determine how often to change the lubricant. What to Use Refer to the Recommended Fluids and Lubricants on page 11‑2 to determine what kind of lubricant to use. Electrical System High Voltage Devices and Wiring { WARNING Exposure to high voltage can cause shock, burns, and even death.
Cadillac Escalade Hybrid - 2012 10-14 Black plate (14,1) Vehicle Care The vehicle also has a special fuse in the battery box for the 300-volt batteries. If this fuse has failed and needs to be replaced, the vehicle will be disabled and you will need to have the vehicle repaired by your dealer. Do not attempt to self-service this fuse.
Cadillac Escalade Hybrid - 2012 Black plate (15,1) Vehicle Care Fuses Usage Relays Usage 8 Drive Motor/Generator Control Module 1 Cabin Heater Pump 9 Drive Motor/Generator Control Module 2 CAB HTR PUMP COOL PUMP Coolant Pump FAN LO Cooling Fan Low Speed Relay FAN MID 1 Cooling Fan Mid 1 10 BECM J‐Case Usage FAN 1 Cooling Fan 1 TRANS PUMP Auxiliary Transmission Fluid Pump FAN 2 Cooling Fan 2 10-15 Relays Usage FAN HI Cooling Fan High Speed Relay FAN MID 2 Cooling Fan Mid 2 F
Cadillac Escalade Hybrid - 2012 10-16 Black plate (16,1) Vehicle Care Wheels and Tires Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Neither tire underinflation nor overinflation is good. Underinflated tires, or tires that do not have enough air, can result in: . Tire overloading and overheating which could lead to a blowout. . Premature or irregular wear. . Poor handling. . Reduced fuel economy.
Cadillac Escalade Hybrid - 2012 Black plate (17,1) Vehicle Care pressure. Using the DIC, tire pressure levels can be viewed. For additional information and details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑5. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Re-check the tire pressure with the tire gauge.
Cadillac Escalade Hybrid - 2012 10-18 Black plate (18,1) Vehicle Care The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See “Tire Inspection,” “Tire Rotation” and “Tires” in the owner manual for more information. Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty.
Cadillac Escalade Hybrid - 2012 Black plate (19,1) Vehicle Care TPMS Sensor Matching Process The TPMS sensor matching process is: Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the vehicle’s tires or replacing one or more of the TPMS sensors. Also, the TPMS sensor matching process should be performed after replacing a spare tire with a road tire containing the TPMS sensor.
Cadillac Escalade Hybrid - 2012 10-20 Black plate (20,1) Vehicle Care Tire Rotation Reset the Tire Pressure Monitor System (TPMS). See Tire Pressure Monitor Operation on page 10‑17. Tires should be rotated every 12 000 km (7,500 mi). Any time unusual wear is noticed, rotate the tires as soon as possible and check the wheel alignment. Also check for damaged tires or wheels. See “When It Is Time for New Tires” and “Wheel Replacement” in the owner manual for more information.
Cadillac Escalade Hybrid - 2012 Black plate (21,1) Vehicle Care It is unusual for a tire to blowout while driving, especially if the tires are maintained properly. If air goes out of a tire, it is much more likely to leak out slowly. But if there ever is a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly.
Cadillac Escalade Hybrid - 2012 10-22 Black plate (22,1) Vehicle Care Tire Sealant and Compressor Kit { WARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see ”Engine Exhaust” in the owner manual.
Cadillac Escalade Hybrid - 2012 Black plate (23,1) Vehicle Care Read and follow all of the tire sealant and compressor kit instructions. The kit includes: Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer.
Cadillac Escalade Hybrid - 2012 10-24 Black plate (24,1) Vehicle Care Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑29. Make sure the on/off button (D) is in the off (O) position. 2. Unwrap the sealant/air hose (G) and the power plug (C). 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4.
Cadillac Escalade Hybrid - 2012 Black plate (25,1) Vehicle Care the accessory power outlet and unscrew the inflating hose from the tire valve. See “Roadside Assistance Program” or “Roadside Service” in the owner manual. 13. Replace the tire valve stem cap. 14. Replace the sealant/air hose (G), and the power plug (C) back in their original location. 10. Press the on/off button (D) to turn the tire sealant and compressor kit off.
Cadillac Escalade Hybrid - 2012 10-26 Black plate (26,1) Vehicle Care 19. Wipe off any sealant from the wheel, tire or vehicle. 20. Dispose of the used tire sealant canister (B) and sealant/air hose (G) assembly at a local dealer or in accordance with local state codes and practices. Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant: 21.
Cadillac Escalade Hybrid - 2012 Black plate (27,1) Vehicle Care 7. Attach the air only hose (F) onto the tire valve stem and press the lever down to secure it. 8. Plug the power plug (C) into the accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See “Power Outlets” in the owner manual. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter.
Cadillac Escalade Hybrid - 2012 10-28 Black plate (28,1) Vehicle Care Removal and Installation of the Sealant Canister To install a new sealant canister: 1. Align the sealant/air hose (G) with the slot in the air compressor. To remove the sealant canister: 2. Push the tire sealant canister (B) down and turn it clockwise. 3. Wrap the sealant/air hose (G) around the air compressor channel to stow it in its original location. 1.
Cadillac Escalade Hybrid - 2012 Black plate (29,1) Vehicle Care Storing the Tire Sealant and Compressor Kit Jump Starting { WARNING The tire sealant and compressor kit is located under the storage tray on the driver side trim panel (over the rear wheelhouse). Personal injury, death, or damage to the vehicle can result if you try jump starting or using a battery charger on the high voltage hybrid battery. Use only the 12-volt battery for jump starting and charging.
Cadillac Escalade Hybrid - 2012 10-30 Black plate (30,1) Vehicle Care If the vehicle's 12‐volt battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Use the following steps to do it safely. { WARNING Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you. . They contain gas that can explode or ignite. . They contain enough electricity to burn you.
Cadillac Escalade Hybrid - 2012 Black plate (31,1) Vehicle Care 4. Open the hood on the other vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. Your vehicle has a remote positive (+) and a remote negative (−) jump starting terminal. You should always use these remote terminals instead of the terminals on the battery. battery post. To uncover the remote positive (+) terminal, open the red plastic cover. 5. The remote negative (−) is a solid engine ground.
Cadillac Escalade Hybrid - 2012 10-32 Black plate (32,1) Vehicle Care { WARNING Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 6. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some basic things you should know.
Cadillac Escalade Hybrid - 2012 Black plate (33,1) Vehicle Care Jumper Cable Removal To disconnect the jumper cables from both vehicles: Towing 1. Disconnect the black negative (−) cable from the vehicle that had the bad battery. Recreational Vehicle Towing 2. Disconnect the black negative (−) cable from the vehicle with the good battery. Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome.
Cadillac Escalade Hybrid - 2012 10-34 Vehicle Care Here are some important things to consider before recreational vehicle towing: . What is the towing capacity of the towing vehicle? Be sure to read the tow vehicle manufacturer's recommendations. . What is the distance that will be travelled? Some vehicles have restrictions on how far and how long they can tow. .
Cadillac Escalade Hybrid - 2012 Black plate (35,1) Vehicle Care Two-wheel drive vehicles should not be towed with the rear wheels on the ground. Two-wheel drive transmissions have no provisions for internal lubrication while being towed. Four-Wheel Drive Vehicles 10-35 { WARNING Shifting a four-wheel-drive vehicle's transfer case into N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). The driver or others could be injured.
Cadillac Escalade Hybrid - 2012 10-36 Black plate (36,1) Vehicle Care After towing, see “Shifting Out of N (Neutral)” under Four-Wheel Drive on page 9‑11. Dolly Towing – Rear Towing (Rear Wheels Off the Ground) 2. Drive the rear wheels onto the dolly. 3. Firmly set the parking brake. See “Parking Brake” in the owner manual. 4. Put the transmission in P (Park). 5. Secure the vehicle to the dolly following the manufacturer's instructions.
Cadillac Escalade Hybrid - 2012 Black plate (37,1) Vehicle Care { WARNING Shifting a four-wheel-drive vehicle's transfer case into N (Neutral) can cause the vehicle to roll even if the transmission is in P (Park). The driver or others could be injured. Make sure the parking brake is firmly set before the transfer case is shifted to N (Neutral). 10-37 7. Shift the transfer case to N (Neutral). See “Shifting into N (Neutral)” under Four-Wheel Drive on page 9‑11. Appearance Care 8.
Cadillac Escalade Hybrid - 2012 10-38 Black plate (38,1) Vehicle Care 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Service and Maintenance Service and Maintenance Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 11-2 Black plate (2,1) Service and Maintenance Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Fluids identified below are specific to the hybrid vehicle and can be obtained from your dealer. See the owner manual for the other fluids and lubricants recommended for the vehicle.
Cadillac Escalade Hybrid - 2012 Black plate (1,1) Technical Data Technical Data Vehicle Data Capacities and Specifications . . . . . . . . . . . . . . 12-2 Engine Drive Belt Routing . . .
Cadillac Escalade Hybrid - 2012 12-2 Black plate (2,1) Technical Data Vehicle Data Capacities and Specifications Capacities Application Automatic Transmission* (Pan Removal and Filter Replacement) Metric English 10.9 L 11.5 qt Cooling System Drive Motor Generator Control Module Cooling System 2.7 L 2.9 qt 6.0L V8 Engine Cooling System 17.3 L 18.3 qt Fuel Tank 92.7 L 24.5 gal Transfer Case Fluid 1.5 L 1.6 qt *Transmission fluid capacity is approximate.
Cadillac Escalade Hybrid - 2012 Black plate (3,1) Technical Data Engine Drive Belt Routing 12-3
Cadillac Escalade Hybrid - 2012 12-4 Black plate (4,1) Technical Data 2 NOTES
Cadillac Escalade Hybrid - 2012 Black plate (1,1) INDEX i-1 A C D Appearance Care Exterior . . . . . . . . . . . . . . . . . . . . . 10-37 Automatic Transmission . . . . . . . . 9-7 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . .10-5 Manual Mode . . . . . . . . . . . . . . . . .9-10 Canadian Vehicle Owners . . . . . . . . .ii Capacities and Specifications . . . . . . . . . . . . . . . . 12-2 Charging System Light . . . . . . . . . 5-4 Circuit Breakers . . . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 i-2 Black plate (2,1) INDEX E F H Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . 10-14 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . 10-13 Engine Compartment Overview . . . . . . .10-4 Coolant Heater . . . . . . . . . . . . . . . . 9-4 Drive Belt Routing . . . . . . . . . . . .12-3 Pressure Light . . . . . . . . . . . . . . . . . 5-4 Running While Parked . . . . . . . . . 9-7 Engine Oil Messages . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 Black plate (3,1) INDEX i-3 M P S Maintenance Schedule Recommended Fluids and Lubricants . . . . . . . . . . . . . . . . . . . 11-2 Transfer Case . . . . . . . . . . . . . . . . 9-11 Manual Mode . . . . . . . . . . . . . . . . . . 9-10 Messages Battery Voltage and Charging . . . . . . . . . . . . . . . . . . . . . 5-6 Brake System . . . . . . . . . . . . . . . . . 5-6 Door Ajar . . . . . . . . . . . . . . . . . . . . . . 5-6 Engine Oil . . . . . . . . . . . . . . . . .
Cadillac Escalade Hybrid - 2012 i-4 Black plate (4,1) INDEX T U Tachometer . . . . . . . . . . . . . . . . . . . . . 5-3 Tires If a Tire Goes Flat . . . . . . . . . . 10-20 Inflation Monitor System . . . . 10-17 Rotation . . . . . . . . . . . . . . . . . . . . 10-20 Sealant and Compressor Kit . . . . . . . . . . . 10-22 Sealant and Compressor Kit, Storing . . . . . . . . . . . . . . . . 10-29 Towing Equipment . . . . . . . . . . . . . . . . . . . .9-17 Recreational Vehicle . . . . . . . .