Installation Manual

ManualsBrandsCafe ManualsDouble Electric Wall OvensCTD90DP4MW2

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT — Save these

instructions for local inspector’s use.

•

IMPORTANT — Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level – Installation of this appliance

requires a qualified installer or electrician.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under Warranty.

• Product is for indoor use only.

Installation Instructions

27” & 30” Electric Built-In Wall Ovens

FOR YOUR SAFETY:

WARNING

Before beginning the installation, switch power off at the service panel and lock

the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a

tag, to the service panel.

Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight

on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,

stand or hang on the oven door.

Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to

200°F [93.3°C]) generated by the oven.

MATERIALS YOU MAY NEED

Junction Box

Wire Nuts

Strain Relief Clamp for 1/2” Conduit

36” (91 cm) of String

TOOLS YOU MAY NEED

1/8” Drill Bit and Electric or Hand Drill

T20 Screwdriver

Phillips Screwdriver

Wire Strippers

7/16” Nut Driver (combination ovens)

1/4” Nut Driver (30” combination ovens)

REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all

packing parts from oven, racks and heating elements. Remove protective film and labels on

the outer door and control panel. Also, remove plastic on trims and panel, all tape around the

oven and any shipping screws securing the oven to the base pad. Open oven door and remove

literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be

installed at the end of the installation process. The trim is wrapped separately and taped to the top

of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).

PREPARE THE OPENING

NOTE: If the cabinet does not have a solid

bottom, two braces or runners must be

installed to support the weight of the oven.

For single ovens, the runners and braces

must support 220 lbs (99 kg). For double and

combination ovens, the runners and braces

must support 400 lbs. (181 kg).

NOTE: If marks, blemishes or the cutout

opening are visible above the installed oven,

it may be necessary to add wood shims

under the runners until the marks or opening

are covered.

NOTE: If the cabinet does not have a front

frame and the sides are less than ¾” (1.9 cm)

thick, shim both sides equally to establish the

cutout width.

ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)

into an approved junction box. A plug and receptacle is NOT permitted on these products.

DESIGN INFORMATION

SINGLE OVEN INSTALLATIONS

The single oven may be installed in a cabinet alone or above a warming drawer. The single oven

may also be installed side by side, below a countertop, or below specified cooktops. See the label

on top of the oven for approved models.

DOUBLE AND COMBINATION OVEN INSTALLATIONS

A double or combination oven may be installed in a cabinet alone or above a warming drawer.

See the label on top of the oven for approved models.

IMPORTANT: Always refer to individual installation instructions packed with each product for

specific requirements.

Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.

In Canada, call 1.800.561.3344 or visit GEAppliances.ca.

Suitable

Bracing

to Support

Runners

2" x 4" (5 cm x 10 cm)

or Equivalent Runners Level

with Bottom of Cutout

and Flush with Sides of Cutout

Summary of content (16 pages)

PAGE 1
Installation Instructions 27” & 30” Electric Built-In Wall Ovens Questions? Call us at 1.800.432.2737 or visit GEAppliances.com. In Canada, call 1.800.561.3344 or visit GEAppliances.ca. BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with Consumer.
PAGE 2
A CUTOUT FOR SINGLE OVENS IN WALL CABINET 2 B CUTOUT FOR SINGLE OVENS – UNDER COUNTER NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both sides equally to establish the cutout width. NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit. H These ovens are not approved for installations that stack one single wall oven above another single wall oven.
PAGE 3
2 C CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS) NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both sides equally to establish the cutout width. H 2 D CUTOUT FOR COMBINATION OVENS (WITH UPPER MICROWAVE OVEN) NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim both sides equally to establish the cutout width.
PAGE 4
2 E SECURING UPPER MICROWAVE/ADVANTIUM OVEN 3 A DETERMINING WHEN TO USE THE PEDESTAL TO CABINET (30” DOUBLE OVENS ONLY) For double oven with microwave or Advantium upper ovens. Secure a wooden cleat to side of cabinet so that the upper oven can be secured to the cleat with provided screws 27” Cabinet requirements • No shims (or cleats) required when cabinet is in minimum width condition. • If cabinet is at maximum width condition, add wood shims to bring cabinet to minimum condition.
PAGE 5
4 A DOOR REMOVAL (RECOMMENDED FOR THERMAL 4 B SHIPPING SCREWS REMOVAL OVENS) (FOR 30” COMBINATION OVEN UPPER OVEN ONLY) Shipping screws must be removed as shown in illustration. You will need a 1/4” Nut Driver. WARNING The door for the microwave oven on a combination oven should never be removed, unless by a certified technician. Hinge Bracket NOTE: Door removal is not a requirement for installation of the product but is an added convenience. To remove the door: A.
PAGE 6
5 ELECTRICAL REQUIREMENTS (CONT.) This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. See the rating plate located on the oven frame to determine the rating of the product. 6 MAKE ELECTRICAL CONNECTIONS WARNING Switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
PAGE 7
8 FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION NOTE: If residence leads are aluminum conductors, see WARNING in Section 5, Electrical Requirements. When connecting to a four-conductor branch circuit, if local codes permit: Black A. Free the neutral (white) lead from being restrained to any Range Branch conduit other wires. If necessary, cut the neutral (white) lead and circuit snaps then re-strip it to expose the proper length of conductor. into box Ground B.
PAGE 8
11 BOTTOM TRIM INSTALLATION 13 REPLACING THE THERMAL OVEN DOOR With oven installed, attach the bottom trim through its mounting holes in front vertical brace using two trim screws provided. Bottom trim lip must be placed under flange of bottom air duct. NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. A. Lift the oven door by grasping each side. B.
PAGE 9
Instrucciones de instalación Hornos de pared eléctricos empotrados de 27” y 30” ¿Preguntas? Comuníquese con nosotros al 1.800.432.273 o visita GEAppliances.com. En Canadá, llame 1.800.561.3344 o visita GEAppliances.ca. ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento. • IMPORTANTE – Guarde estas instrucciones para el uso de inspectores locales. • IMPORTANTE – Cumpla con todos los • códigos y ordenanzas vigentes.
PAGE 10
2 A ABERTURA PARA HORNOS ÚNICOS EN UN GABIENTE DE PARED NOTA: Si el gabinete no cuenta con un armazón frontal y los lados son menores a un grosor de 3/4” (1,9 cm), coloque cuñas uniformemente sobre ambos lados para establecer al ancho de la abertura. Ubicanción de la caja de conexiones (la caja de conexiones puede hallarse en un gabinete adyancente) La abertura entre las paredes nternas debe ser de por lo menos 28-1/2” (72,4 cm) E 22” (55,9 cm) mín.
PAGE 11
2 C ABERTURA PARA HORNOS DOBLES (2 HORNOS TÉRMICOS) NOTA: Si el gabinete no cuenta con un armazón frontal y los lados son menores a un grosor de 3/4” (1,9 cm), coloque cuñas uniformemente sobre ambos lados para establecer al ancho de la abertura.
PAGE 12
2 E CÓMO ASEGURAR EL HORNO MICROONDAS/ ADVANTIUM SUPERIOR AL GABINETE Para hornos dobles como hornos superiores con microondas o Advantium. Asegure un taco de Madera sobre el costado del gabinete, de modo que el horno superior pueda ser asegurado al taco con los tornillos provistos. Requisitos para el gabinete de 27” • No se requiere el uso de cuñas (o tacos) cuando el gabinete se encuentre en la condición de ancho mínimo.
PAGE 13
4 A REMOCIÓN DE LA PUERTA (RECOMENDADO PARA HORNOS TÉRMICOS) ADVERTENCIA La puerta del horno microondas en un horno combinado nunca debe ser retirada, a menos que esto sea realizado por un técnico certificado. Soporte de la Bisagra 4 B RETIRO DE LOS TORNILLOS DE EMBALAJE (PARA HORNO SUPERIOR COMBINADO DE 30” ÚNICAMENTE) Los tornillos de embalaje deben ser retirados como se muestra en la ilustración. Necesitará un destornillador de ¼”.
PAGE 14
5 6 REQUISITOS ELÉCTRICOS (CONT.) Este aparato debe recibir el voltaje y frecuencia adecuados, y debe conectarse a un circuito derivado individual con adecuada conexión a tierra, protegido por un interruptor de circuitos o fusible. Ver la placa de clasificación ubicada en el armazón del horno para determinar la clasificación del producto.
PAGE 15
8 10 A CONEXIÓN DE CIRCUITO DERIVADO DE CUATRO CONDUCTORES NOTA: Si los cables domésticos son conductores de aluminio, ver la ADVERTENCIA de la sección 5, Requisitos eléctricos. • Deslice el horno por la distancia que falta dentro de la abertura para que las bridas laterales y el panel de control se encuentren contra el armazón del gabinete. Verifique que el horno esté centrado en la abertura.
PAGE 16
11 INSTALACIÓN DEL REBORDE INFERIOR Una vez instalado el horno, adjunte el borde inferior a través de sus agujeros de montaje frente al soporte vertical, utilizando los dos tornillos con cabeza recortada provistos. El labio de la cubierta inferior deberá ser ubicado debajo de la brida de la parte inferior del conducto de aire. 13 REEMPLAZO DE LA PUERTA TÉRMICA DEL HORNO NOTA: La puerta del horno es pesada.