LenderOutlook Device Install Guide Installation Instructions LMU-3XX LMU-4XX CalAmp Corporation 1401 N. Rice Avenue, Oxnard, CA 93030 Phone: 805.987.9000 Fax: 805.987.8359 www.calamp.com LMU-7XX LMU-8XX LMU-1175 CAT-720 Document: MBUD-0266v1.
CalAmp | LenderOutlook Device Install Guide CalAmp | LenderOutlook Device Install Guide Copyright © 2014 CalAmp Corporation. All rights reserved. Printed in the United States of America. All trademarks used are properties of their respective owners. Products offered may contain software proprietary to CalAmp or other parties. The offer of these products and services does not include or infer any transfer of ownership.
CalAmp | LenderOutlook Device Install Guide TABLE OF CONTENTS 1 REGULATORY INFORMATION .....................................................................................1 1.1 HUMAN EXPOSURE COMPLIANCE STATEMENT ............................................................................... 1 1.2 LMU-XXX HANDLING PRECAUTIONS ........................................................................................... 2 2 GUIDE PREREQUISITES.............................................................
CalAmp | LenderOutlook Device Install Guide 5.5.1 5.6 6 7 INSTALLATION INSTRUCTIONS FOR EXTERNAL ANTENNA .................................................................. 23 CAT-720 OVERVIEW.................................................................................................. 24 6.1 CAT-720 ENVIRONMENTAL SPECIFICATIONS ............................................................................... 25 6.2 PLAN THE INSTALLATION..............................................................
CalAmp | LenderOutlook Device Install Guide LIST OF FIGURES Figure 1: CalAmp LMU-XXX Device..................................................................................................... 5 Figure 2: Coil Excess Cable ............................................................................................................... 12 Figure 3: Tamper Resistant Materials...............................................................................................
CalAmp | LenderOutlook Device Install Guide 1 REGULATORY INFORMATION 1.1 HUMAN EXPOSURE COMPLIANCE STATEMENT Pursuant to 47 CFR § 24.52 of the FCC Rules and Regulations, personal communications services (PCS) equipment is subject to the radio frequency radiation exposure requirements specified in § 1.1307(b), § 2.1091 and § 2.1093, as appropriate.
CalAmp | LenderOutlook Device Install Guide 1.2 LMU-XXX HANDLING PRECAUTIONS Electrostatic Discharge (ESD) Electrostatic discharge (ESD) is the sudden and momentary electric current that flows between two objects at different electrical potentials caused by direct contact or induced by an electrostatic field. The term is usually used in the electronics and other industries to describe momentary unwanted currents that may cause damage to electronic equipment.
CalAmp | LenderOutlook Device Install Guide Electrical Over-Stress (EOS) The LMU-XXX GPS receiver can be damaged if exposed to an RF level that exceeds its maximum input rating. Such exposure can happen if a nearby source transmits an RF signal at sufficiently high level to cause damage. Storage and Shipping One potential source of EOS is proximity of one LMU-XXX series device or CAT-720 GPS Antenna to another LMU-XXX series device or CAT-720 GSM Antenna.
CalAmp | LenderOutlook Device Install Guide 2 GUIDE PREREQUISITES In order to limit the size and scope of this guide, the following assumptions have been made about the reader. You are familiar with GPS concepts and terminology. You have some experience with installing equipment in vehicles. Page 4 MBUD-0266v1.
CalAmp | LenderOutlook Device Install Guide 3 LMU-XXX OVERVIEW The CalAmp Location and Messaging Unit (LMU-XXX) is a mobile device that resides in private, commercial or government vehicles. The LMU-XXX is a single box enclosure, incorporating a processor, a GPS receiver, a wireless data modem and a vehicle-rated power supply. The device supports inputs and outputs to monitor and react to the vehicular environment and driver actions. 3.
CalAmp | LenderOutlook Device Install Guide 3.2 LMU-XXX ENVIRONMENTAL SPECIFICATIONS The LMU-XXX is designed to operate in environments typically encountered by fleet vehicles, including wide temperature extremes, voltage transients and potential interference from other vehicle equipment. To ensure proper operation in such an environment, the LMU-XXX was subjected to standard tests defined by the Society of Automotive Engineers (SAE). The specific tests included temperature, shock, vibration and EMI/EMC.
CalAmp | LenderOutlook Device Install Guide 3.3 WIRING 3.3.1 LMU-3XX The LMU-3XX has 4 22AWG leads for its power and I/O connections. These leads are mapped as follows: Wire Description Usage Black Ground (-) Required Red Power (+) Required Ignition “on” Input Required for Starter Disable Required for Payment Reminder Buzzer Required for use of Sleep Mode Optional for basic location Output to Starter Relay Required for Starter Disable White Green 3.3.
CalAmp | LenderOutlook Device Install Guide 3.3.3 LMU-7XX AND LMU-8XX The LMU-7XX and LMU-8XX have 8 22AWG leads for its power and I/O connections.
CalAmp | LenderOutlook Device Install Guide 3.3.4 LMU-1175 The LMU-1175 is designed for outdoor use on recreational vehicles and motorcycles.
CalAmp | LenderOutlook Device Install Guide 3.3.5 HOW TO DETERMINE DEVICE CAPABILITY Device part numbers correlate to device features. For example: XXX-YYY-ZZ-NN-USABCD (Example: CVF-322-23-US1970) XXX – Product features CVF = Vehicle Finance CMF = Motorcycle Finance CVT = Vehicle Tracking YYY – Device (322, means LMU-322, etc.
CalAmp | LenderOutlook Device Install Guide 4 LMU-XXX PRE-INSTALLATION CONSIDERATIONS Installation can have a major impact on the performance of the LMU-XXX. It is recommended that installers be familiar with the installation of GPS and cellular devices and are comfortable in a vehicle environment. The best way to ensure a trouble-free installation is to consider your options and make appropriate decisions before you start.
CalAmp | LenderOutlook Device Install Guide 4.3 VISIBILITY OF DIAGNOSTIC LEDS The LMU-XXX’s status LED lights provide valuable information about the device performance and operation. When feasible, attempt to install the LMU-XXX in such a way that the lights are visible with reasonable ease. If you observe poor performance, you may need to read the LEDs to troubleshoot the issue. If you cannot resolve the issue, you will need to provide the LED information to the CalAmp Customer Support Team.
CalAmp | LenderOutlook Device Install Guide 4.6 MOISTURE AND WEATHER PROTECTION The LMU-XXX is not a weatherproof device and must be kept dry. The mounting location should be inside the passenger compartment of the vehicle safe from physical damage and where it is not exposed to moisture or water.
CalAmp | LenderOutlook Device Install Guide 5 LMU-XXX INSTALLATION Installing the LMU-XXX is not difficult, but you must consider the variables involved, such as the vehicle type and location of existing equipment. Installation time can vary depending upon the installer’s experience and the vehicle design. The average time for installation is approximately 45 minutes. A single individual can perform most installation operations. To install the LMU-XXX: 1.
CalAmp | LenderOutlook Device Install Guide 5.1 MOUNTING PROCEDURE FOR INTERNAL ANTENNA DEVICES When determining mounting location, the primary consideration is GPS satellite visibility. LMU-XXX have internal antennas for both GPS and Cellular. The GPS antenna is located directly under the product label side of the device. The required install orientation of the LMU-XXX is a horizontal mount, label side up. Attach the LMU-XXX to the solid body of the vehicle not to plastic panels.
CalAmp | LenderOutlook Device Install Guide Recommended mounting locations for optimal performance include in-dash mounts where the LMU-XXX will not be shielded by metal: • Above gauge cluster • Above radio (prevent possible interference by routing power harness away from radio wires) • Above air vents or air duct • Glove box • Center console Figure 5: LMU-XXX Example Mount 5.2 CONNECT THE STANDARD WIRING HARNESS Next, connect the Standard Wiring Harness.
CalAmp | LenderOutlook Device Install Guide 5.3 CONNECT THE OBD-II WIRING HARNESS This section contains the information required to connect the OBD-II Wiring Harness. This harness enables you to obtain power and ground signal from the vehicle without splicing wires from your vehicle. Note that you must still connect the ignition sense wire to the true ignition wire on the vehicle. Note: If you are using the Standard Wiring Harness, skip this section and refer to Connect the Standard Wiring Harness.
CalAmp | LenderOutlook Device Install Guide 3. Secure the LMU-XXX OBD-II harness connector and the OBD-II connector together with tape to prevent loose connections that may occur from normal vehicle operation vibration. Figure 9: Plugged OBD-II Connectors and Taped Connectors 4. Re-mount the LMU-XXX OBD-II harness connector in the vehicle’s original location. 5.
CalAmp | LenderOutlook Device Install Guide 5.4 CONNECT OPTIONAL OUTPUTS The options available for the LMU-XXX devices include starter disable and payment reminder. Note: When connecting the I/O, you may be required to provide additional length of 22AWG wire, depending on where the I/O connection is located compared to the Power/Ign/Ground connections. 5.4.
CalAmp | LenderOutlook Device Install Guide For Devices with an internal relay (LMU-4xx) 1. Locate and cut the Starter Wire + in the vehicle’s ignition harness. 2. Connect one of the Green wires from the device to the Ignition Switch side of the cut Starter Wire. o Once cut, this wire will show voltage during cranking. o Use red butt crimp connectors to make the connections. 3. Connect the other Green Wire from the device to the Starter Solenoid side of the cut Starter Wire. 5.4.
CalAmp | LenderOutlook Device Install Guide 5.4.3 PAYMENT REMINDER AND NOTIFICATION The LMU-7XX and LMU-8XX use the optional Output #2 to send a 30 second sink to ground through the Yellow wire of the LMU-XXX wiring harness to the Piezo Buzzer (4C765). Figure 12: Piezo Buzzer Connection 1. The buzzer may come with a connector on the end and/or resistors spliced into the wire near the buzzer.
CalAmp | LenderOutlook Device Install Guide 5.5 LMU-XXX INSTALLATION VERIFICATION Installers should verify that the LMU-XXX GPS and communication functions are working properly before departing the installation site. Installation is complete and successful when you have tested the device. Using LenderOutlook’s mobile app, MobileInstallTM, you can install the vehicle in LenderOutlook and verify device installation from your mobile device.
CalAmp | LenderOutlook Device Install Guide 5.6 INSTALLATION INSTRUCTIONS FOR EXTERNAL ANTENNA Only the LMU-8xx-3x device supports an external antenna. If you have purchased one of the devices with a part number CVF-810-33, -34 or -37 you should have received p/n IV1353-QB-02 SMA/SMC 3M Quadband cell antenna with your kit. This antenna connects to the GPS and cellular SMx ports on the device.
CalAmp | LenderOutlook Device Install Guide 6 CAT-720 OVERVIEW The CAT-720 is a battery-operated product with a field-replaceable battery designed for multi-year deployments. It features a small size, superior GPS performance and an internal 57 Ah battery. The CAT720 is a complete asset tracking and communication device incorporating next-generation, supersensitive GPS technology for installation in any mobile asset.
CalAmp | LenderOutlook Device Install Guide 6.1 CAT-720 ENVIRONMENTAL SPECIFICATIONS The CAT-720 is designed to operate in environments specified below: SPECIFICATIONS General Specifications Location technology: 50 channel GPS Operating voltage: 3.6 volt internal battery pack GPS Specifications Location technology: 50 channel GPS (with SBAS: WAAS, EGNDS, MSAS, GAGAN) Location accuracy: 2.
CalAmp | LenderOutlook Device Install Guide 6.2 PLAN THE INSTALLATION Proper installation of the CAT-720 can have a major impact on the device’s performance. It is recommended that installers be familiar with the installation process prior to installing the device. Before drilling any holes, determine the location of each hardware component will be. Be advised that an installation that violates the environmental specifications of the CAT-720 will void the warranty.
CalAmp | LenderOutlook Device Install Guide 7 CAT-720 INSTALLATION Installation time can vary depending upon the installer’s experience and the asset design. The average time for installation is approximately 60 minutes. A single individual can perform most installation operations To Install CAT-720: 1. Ensure mounting surface is level, rust and dirt free. Figure 15: Example CAT-720 Installation (Previous model shown) 2.
CalAmp | LenderOutlook Device Install Guide Figure 16: Sealant Applied to Backside 5. Apply RTV sealant inside the mounting holes. 6. Feed mounting screws from inside. 7. Mount device on screws and tighten nuts. • Caution: Drive screws at low speed to avoid seizing. 8. Remove the activation magnet from the front of the device. • The activation magnet interrupts power to the device. In order to activate device reporting, you must remove the activation magnet.
CalAmp | LenderOutlook Device Install Guide 7.1 CAT-720 BATTERY REPLACEMENT The following steps outline the procedure to remove and replace the CAT-720 battery pack. To Replace the CAT-720 Battery: 1. Remove Battery Cap. Figure 17: Remove Battery Cap 2. Insert Phillips head screw driver and remove the four (4) screws. 3. Remove the end cap and set aside. 4. Disconnect power cable. 5. Remove the rubber gasket and set aside. Figure 18: Disconnect the Battery Connector 6.
CalAmp | LenderOutlook Device Install Guide Figure 19: Power Disconnected 7. Remove the battery pack. Figure 20: Proper Alignment to Slide Battery Out and In of Enclosure 8. Ensure the gap in battery pack foam is aligned with device power cable. 9. Slide the battery pack out of the enclosure. 10. Slide replacement battery pack into the enclosure and replace gasket. Page 30 MBUD-0266v1.
CalAmp | LenderOutlook Device Install Guide Figure 21: Reconnect Power Cables 11. Reconnect the white connectors. 12. To replace the battery cap, seat the cap housing to the gasket to ensure a tight fit. 13. Insert the screws, use a Phillips head screw driver and turn clockwise until hand tight. • All lithium batteries whether recycled or disposed must be done in accordance with applicable local, State and Federal regulations • End of replacement procedure. MBUD-0266v1.
CalAmp | LenderOutlook Device Install Guide 8 LIMITED WARRANTY Covering the Physical Media and Printed Materials: CalAmp warrants to you, the original licensee, that the media on which the Software is recorded are free from defects in materials and workmanship under normal use and service FOR A PERIOD OF NINETY (90) DAYS FROM THE DATE OF DEVELOPER LICENSE PURCHASE.
CalAmp | LenderOutlook Device Install Guide Acknowledgement: You acknowledge that you have read this LIMITED WARRANTY, understand it and agree to be bound by its terms and conditions.
