User Manual

Quick Guide
Appearance
1. LED Indicator (Blue)
2. Power on/off button
3. Volume down button
4. Volume up button
5. Multi-function button (MFB)
6. Microphone location
7. Speaker location
8. Bendable ear-hook
9. USB charging port
Charging
"For optimizing battery performance, the
headset must be charged for at least 12
hours for the first time."
Subsequent full charge requires around 2.5
hours. (Five short tones warning every 20
seconds mean that the battery level is low and
immediate charging is required.)
How to Charge
3.Power source for charging is from travel
charger adapter (optional) or standard
mini USB cable connected to computer/
notebook USB port.
1.Plug in charger/ USB cable into the charging
port. During charging, blue indicator will
light up.
2.When fully charged blue indicator light goes off.
Switching On/Off the Headset
<On>Press and hold power switch for more
than 4 seconds. Blue indicator light will
flash rapidly 4 times and at the same
time an audio tone can be heard
through the speaker, indicating
headset been switch on.
<Off>Press and hold power switch for more
than 4 seconds. Blue indicator light
will flash rapidly 2 times and at the
same time an audio tone can be heard
through the speaker, indicating
headsets been switched off.
Pairing the Headset to Your
Phone
1.Make sure the headset is off.
2.Press and hold on the power switch button
for approximately 8 seconds until the LED
indicator is always on (no flashing).
3.Turn on your phone's Bluetooth function
and search for device.
4.Select the device "I-MOBILE BHS-304"
device listed on the phone
screen.
from the found
5.Enter "0000" as the password and select
OK. When your headset is successfully
paired, the indicator light changes to rapid
blue flashes and at the same time an audio
tone can be heard through the speaker.
6.If the phone fails to connect to the headset
automatically after being paired, tab the
MFB once, and the headset will try to
connect to phone. Your phone may ask you
to confirm the connection with the headset,
please select "Yes". Retry if failed.
7.The pairing mode will last 120 seconds,
before going into standby mode. If pairing
fails or timeout, repeat all over again from
step 1.
Making & Answering Calls
Action
HS Profile
Tab the MFB
Tab the MFB
Function
Device Status
Phone
Headset
HF Profile
Making a voice
dial call
Standby Standby
Standby
Standby
Standby Standby
Tab the MFB None
None
None
None None
Redial last call
Long press the
MFB
Long press the
MFB
Long press the
MFB
None
Long press the
MFB
Receive a call
Ringing
Ringing
Reject a call
End a call
Conn-
ected
Conn-
ected
Conn-
ected
Conn-
ected
Toggle between
two active calls
Conn-
ected &
On hold
Conn-
ected &
Ringing
Answer a
second
incoming call
LED Indication
Action
HS Profile
Function
Device Status
Phone
Headset
HF Profile
Standby : not on call, Ringing : in coming call
Connected: on a call, On hold : 1 call been placed on hold
Tab the MFB None
Conn-
ected
Conn-
ected &
On hold
End a current
call
Headset status
4 rapid flashes
10 rapid flashes
1 Fast flash per 3 seconds
1 Slow flash per 8 seconds
Power off
Action
Power On
2 rapid flashes
Charging & Pairing mode Always on (no flashing)
Pairing succeeded
Standby mode
Connected
Battery fully charged Indicator light turn off
Audio Tones
Headset status The audio tone
Power on
Power off
Single Tone
Single Tone
Single high tone
Pairing success
1 single high tone
1 single high tone
Income call
Melody tone
Long press the MFB
Battery low
Connect success
Connect failed
5 rapid high tones per 20
seconds
No network service
2 rapid high tones per
20 seconds
Microphone muted
Reached Max./Min.
Volumes
1 low tone per 5 seconds
2 tones from low to high
2 tones from high to low
Notice
1.It is normal that the battery life will gradually
deteriorate, from repeated charging of the headset.
2.The headset will be switch off during charging for
safety reasons.
15.105 Federal Communications
Commission (FCC) Requirements,
Part 15
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions.
2.This device may not cause harmful interference.
1.This device must accept any interference received,
including interference that may cause undesired
operation.
Declaration of Conformity
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct
theinterference by one or more of the following
measures:
This equipment generates, uses and can radiate radio
frequency energyand, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
Consult the dealer or an experienced radio/TV
technician for help.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Increase the separation between the equipment and
receiver.
Reorient or relocate the receiving antenna.
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation.
Regulatory information / Disclaimers
Installation and use of this Bluetooth headset device
must be in strict accordance with the instructions
included in the user documentation provided with the
product. Any changes or modifications (including the
antennas) made to this device that are not expressly
approved by manufacturer may void the user's
authority to operate the equipment. Manufacturer is
not responsible for any radio or television
Interferencecaused by unauthorized modification of
this device, or the substitution of the connecting
cables and equipment other than manufacturer
specified. It is the responsibility of the user to correct
any interference caused by such unauthorized
modification, substitution or attachment. Manufacturer
and its authorized resellers or distributors will assume
no liability for any damage or violation of government
regulations arising from failing to comply with these
guidelines.
This product complies with the following
standards:
EN 300 328
EN 301 489-1/-17
EN 60950