Installation and Operating Instructions AC Variable Speed Drive 0.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Easy Start Up Guide: QD:Neo IP20 AC Supply Connection 3 Phase Units : Connect L1, L2, L3, PE 1 Phase Units : Connect L1, L2, PE Fuses or MCB Supply Voltage 200 - 240 Volts +/- 10% 380 - 380 Volts +/- 10% Fuses or MCB Check the drive rating information on pages 41 & 42 Hel
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Easy Start Up Guide: QD:Neo IP55 Display Keypad Operation can be found on page 20 IMPORTANT SAFE TORQUE OFF (STO) 1 9 12 13 Link the terminals as shown, through the emergency stop circuit contacts Control terminals 1 5 6 7 Run - Stop 10K Speed Close the switch Pot
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Easy Start Up Guide: QD:Neo IP66 Display Keypad Operation can be found on page 20 IMPORTANT SAFE TORQUE OFF (STO) 1 9 12 13 Link the terminals as shown, through the emergency stop circuit contacts Control terminals 1 2 5 6 7 Run - Stop 10K Speed Close the switch
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 1. Introduction 1.1 Important Safety Information 7 2. General Information and Ratings 8 2.1 Drive Model Numbers - IP20 8 2.2 Drive Model Numbers - IP55 8 2.3 Drive Model Numbers - IP66 9 3. Mechanical Installation 10 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Declaration of Conformity ERIKS Industrial Services Ltd hereby states that the Fenner QD product range conforms to the relevant safety provisions of the Low Voltage Directive 2006/95/EC and the EMC Directive 2004/108/EC and has been designed and manufactured in accordance
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 1. Introduction Danger: Indicates a potentially hazardous situation other than electrical, which if not avoided, could result in damage to property. 1.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 2. General Information and Ratings 2.1 Drive Model Numbers - IP20 Series & Inverter Supply Enclosure Type Voltage 200-240V 10% - 1 Phase Input kW Model with Filter 572N20P7 572N21P5 572N22P2 572N20P7 Rated Power Kw 0.75 1.5 2.2 HP 2 2 2 Output Current (A) 4.3 7 10.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 2.3 Drive Model Numbers - IP66 200-240V 10% - 3 Phase Input kW Model with Filter 576N20P7 576N21P5 576N22P2 Kw 0.75 1.5 2.2 HP 1 2 3 Output Current (A) 4.3 7 10.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3. Mechanical Installation 3.1 General • The Fenner QD:Neo should be mounted in a vertical position only on a flat, flame resistant vibration free mounting using the integral holes or DIN rail clip (Frame Size 2 only).
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3.5 Guidelines for Enclosure Mounting (IP20 Units) • Installation should be in a suitable enclosure, according to EN60529 or other relevant local codes or standards. • Enclosures should be made from a thermally conductive material.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3.7 Mechanical Dimensions (IP55 Units) H I B C G F Drive Size D A B mm in mm mm E G C in A D in mm E in F mm in G mm in H I mm in mm in mm in 4 440 17.32 418 16.46 423 16.65 8 0.315 240 9.449 171 6.732 110 4.331 4.25 0.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3.9 Mechanical Dimensions (IP66 Units) A D B I J E H G Drive Size A mm F B D in mm in mm E F G in mm in mm in mm H in I J mm in mm in mm in 2 257 10.1 220 8.67 200 7.9 29 1.1 238 9.37 188 7.4 176 6.9 4.2 0.2 8.5 0.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3.11 Removing the Terminal Cover 3.11.1 Frame Size 2 3.11.2 Frame Size 3 Terminal Cover Release Screws 3.11.3 Frame Size 4 Using a suitable flat blade screwdriver, rotate the four retaining screws indicated until the screw slot is verical. Page 14 3.11.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 3.11.5 Frame Size 6 & 7 Remove the screws indicated, lift the cover forwards and off. To refit the cover, slide the top locating lugs upwards under the top cover, then refasten the lower cover screws. www.fptgroup.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 4. Electrical Installation ground terminals on the drive. 4.15 Ground Fault Monitoring 4.1 Grounding the Drive This manual is intended as a guide for proper installation.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı suitable; however in some cases type aR fuses may be required. The operating time of the fuses must be below 0.5 seconds.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 4.7 Motor Thermistor Connection Where a thermistor is to be used, it should be connected as follows: Control Terminal Strip 1 2 3 4 5 6 7 8 Additional information • Compatible thermistor: PTC Type, 2.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 4.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5. Managing the Keypad The drive is configured and its operation monitored via the keypad and display 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5.5 Keypad Layout and Function - Optional OLED Keypad (IP55 units Only) For IP55 drives, an optional Multi Language OLED display keypad may be specified at the time of order, option code - Tx.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5.8 Changing the Language in OLED Display Hold down the Start, Navigate and UP keys for >1s Use the Up and Down arrows to select a language. Press the Navigate button to select. 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5.10 Terminal Control When delivered, the Fenner QD:Neo is in the factory default state, meaning that it is set to operate in terminal control mode and all parameters have the default values as indicated in section 6.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 6.0 Parameters 6.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı P1-11 P1-12 P1-13 P1-14 V/F Mode Voltage Boost 0.0 Drive Rating Dependent % Voltage boost is used to oncrease the applied motor voltage at low output frequencies, in order to improve low speed and starting torque.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 7. Digital Input Functions 7.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 17 O : Stop C : Run Fwd O : Stop C : Run Rev O : Stop C : Run Fwd O : Stop C : Run Rev O : Stop C : Run Fwd O : Stop C: Run Rev O : Stop C: Run Fwd Normally Open (N.O.) Close to run Fwd O : Stop C: Run Rev Normally Closed (N.C.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 8. Extended Parameters 8.1 Parameter Group 2 - Extended Parameters Par P2-01 Parameter Name Preset / Jog Frequency / Speed 1 Minimum P1-02 Maximum P1-01 Default 5.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 4 : Output Frequency >+ Limit. Logic 1 when the motor speed exceeds the adjustable limit 5 : Output Current >=Limit. Logic 1 when the motor current exceeds the adjustable limit 6 : Output Torque >=Limit.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı P2-22 0 Display Scaling Source 2 0 - P2-21 & P2-22 allow the user the program the Fenner QD:Neo to display an alternative output unit scaled from an existing parameter, e.g. to display conveyor speed in metres per second based on the output frequency.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı P2-33 Analog Input 2 (Terminal 10) Format U 0-10 See Below - U 0-10 = 0 to 10 Volt Signal (Uni-polar) U 10-0 = 10 to 0 Volt Signal (Uni-polar) Ptc-th = Motor PTC Thermistor Input A 0-20 = 0 to 20mA Signal t r t r P2-34 4-20 = 4 to 20mA Signal, the Fenner QD:Neo will t
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 8.2 Parameter Group 3 - PID Control Par P3-01 Parameter Name PID Proportional Gain Minimum 0.1 Maximum 30.0 Default 1.0 Units - PID Controller Proportional Gain.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 8.3 Parameter Group 4 - High Performance Motor Control Incorrect adjustment of parameters in menu group 4 can cause unexpected behaviour of the motor and any connected machinery. It is recommended that these parameters are only adjusted by experienced users.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 8.4 Parameter Group 5 - Communication Parameters Par P5-01 Parameter Name Drive Fieldbus Address Minimum 0 Maximum 63 Default 1 Units - 125 1000 500 kbps 9.6 115.2 115.2 kbps - - n-1 - 0.0 5.0 1.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 8.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Par P0-26 P0-27 P0-28 P0-29 P0-30 P0-31 P0-32 P0-33 P0-34 P0-35 P0-36 P0-37 P0-38 P0-39 P0-40 P0-41 P0-42 P0-43 P0-44 P0-45 P0-46 P0-47 P0-48 P0-49 P0-50 Description Energy Consumption kWH Meter Units kWh Displays the amount of energy consumed by the drive in kWh.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 9.0 Serial Communications 9.1 RS-485 Communications The Fenner QD:Neo has an RJ45 connector on the front of the control panel. This connector allows the user to set up a drive network via a wired connection.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 9.2.2 Modbus Control & Monitoring Registers The following is a list of accessible Modbus Registers available in the Fenner QD:Neo drive.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 10.0 Technical Data 10.1 Environmental Ambient temperature Operational : -10...50°C (IP20 units), 40°C (IP55 units) Storage : -40°C...
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 380 - 480 Volt (+/-10%) 3 Phase Input, 3 Phase Ouput kW HP Frame Size Nominal Input Current Fuse or MCB (type B) Supply Cable Size Nomibal Output Current 150% Output Current 60 secs Motor Cable Size Max Motor Cable Length Optional Brake Resistor Min Rec Ω Amps
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı 11. Troubleshooting 11.1 Fault Messages Fault Code No 00 01-b 01 0L-br 02 0-1 03 .
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Fault Code th-Flt data-f No 16 17 Description Faulty thermistor on heatsink Internal memory fault 4-20f 18 4-20mA signal lost data-e 19 Internal memory fault u-def f-ptc fan-f 0-heat 20 21 22 23 User parameter defaults Motor PTC Over temperature Cooling fan faul
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı www.fptgroup.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı Page 46 www.fptgroup.
Neo Installation & Operating Instructions ııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııııı www.fptgroup.
82-P2MAN-FN_V1.10 82-P2MAN-FN_V1.
