User's Manual
Table Of Contents
- LMU-3030 Hardware & Installation Guide
- [edit][top]1 Introduction
- 2 - System Overview
- 3 – Hardware Overview
- 3.1 Location messaging unit LMU-3030™
- 3.1.1 LMU-3030™ Handeling Precautions:
- 3.1.2 Battery backup devices
- Please properly dispose of the battery in any of the CalAmp products that utilize one, do not just throw used batteries, replaced batteries, or units containing a back-up battery into the trash. Consult your local waste management facility for proper ...
- 3.1.3 Environmental Specifications
- 3.1 LMU-3030™ connectors
- 3.2.1 Primary connector
- 3.2.2 Serial Adapter
- LMU Serial Cable (Part Number 133337)
- 3.3.1 Three-Axis accelerometer input
- the LMU-3030™ supports an internal 3 Axis Precision Accelerometer as one of its discreet inputs. When the LMU is moved in any direction, the associated input will be in the High state. If the LMU’s accelerometer does not detect motion, then the input ...
- 3.3.2 Status LEDs
- 4 – Configuration and activation
- You have contacted the CalAmp sales team regarding the network availability of the LMU-3030™. This device may not be supported for all the carriers or networks listed in this section (CDMA-Verizon, CDMA-Sprint, HSPA, GSM), for product availability c...
- 4.1 Quick Start – General config
- All LMU-3030s™ must go through a common step during the configuration and provisioning process. Specifically, this is pointing the LMU to your LM Direct™ server, either via IP or a URL.
- [edit][top]4.4 Accessing the SIM
- 6. Insert the SIM into the LMU.
- 7.
- 4.5 Activating a CDMA LMU-3030™
This field, if present, indicates a problem with the LMU’s GPS antenna. A value of Short indicates that
the antenna cable has likely been crushed. A value of Open indicates that the antenna cable is either
cut or disconnected. A value of Off indicates that the LMU’ GPS receiver is off.
- [No Time Sync]:
If this field is present, it indicates that the LMU’s GPS receiver has not been able to find even a single
GPS satellite. This would likely been seen in conjunction with the above antenna error, or if the LMU
GPS antenna is otherwise blocked.
- [<FixStatus> <Sat Count>]:
If these fields are present it indicates that the LMU has, or had a valid GPS solution. The <Sat Count>
field indicates how many GPS satellites are currently in use by the LMU. The <FixStatus> field
indicates the type of fix. The Fix Status types are detailed in the
LM Direct Reference Guide.
INP:
o <input states>:
This field details the current state of each of the LMU’s discreet inputs. This field is always 8
characters long. The left most character represents the state of input 7 where the right most represents
the state of input 0 (i.e. the ignition). A value of 1 indicates the input is currently in the high state. A
value of 0 indicates it is currently in the low state.
o <vehicle voltage>:
This field will contain the current reading of the LMU’s internal A/D. This will be the supply voltage
provided to the LMU in mV.
MID:
o <mobile ID>:
This will be the current mobile ID in use by the LMU.
o <mobile ID type>:
This will be the type of Mobile ID in use by the LMU. The available types are, Off, ESN, IMEI, IMSI,
USER, MIN and IP ADDRESS.
INB:
o <inbound IP address>:
This is the current IP address in use by the LMU. This value should match the IP address of your LM
Direct™ server.