8015UG-E-B 7/31/03 3:43 PM Page 1 ULTRA MEASURE MASTER ® Conversion Calculator CALCULATED INDUSTRIES ® ULTRA MEASURE MASTER ® Off gpm oz/sec liters/sec mL/sec On/C wt/vol gal fl oz liters mL met tons psi psf kPa MPa tons lbs dry oz kg grams Cu m/min km/h % m/sec mm/sec Sq m cm mm ft/min ft/sec in/sec EXP mph Yds Feet Inch / Miles CONV Stor Rcl √ __ in-lbs ft-lbs N-m 7 8 9 ÷ Hectare Acre Acre-Ft AC x 4 5 6 BdFt °C °F π 1 2 3 + Bars Per
8015UG-E-B 7/31/03 3:43 PM Page 2 TABLE OF CONTENTS Introducing Ultra Measure Master . . . . . . . . . .3 Key Definitions . . . . . . . . . . . . . . . . . . . . . . . .4 Operating Basics . . . . . . . . . . . . . . . . . . . . . .12 Power On & Off . . . . . . . . . . . . Conventions & Units of Measure Fractional Settings . . . . . . . . . . . Preference Feature . . . . . . . . . . . Basic Math Operations . . . . . . . . Memory Operation . . . . . . . . . . . Paperless Tape Feature . . . . . . . . . .
8015UG-E-B 7/31/03 3:43 PM Page 3 INTRODUCING ULTRA MEASURE MASTER® The Ultra Measure Master ® calculator simplifies conversions between metric and English weights and measures.
8015UG-E-B 7/31/03 3:43 PM Page 4 KEY DEFINITIONS [+] [–] [x] [÷] [=] Arithmetic operation keys. [0] – [9] and [•] Digits used for keying in numbers. [Off] — Off Key Turns all power off. [On/C] — On/Clear Key Turns on power. Pressing once clears the display. Pressing twice clears all temporary registers but does not clear scales. [Stor] — Storage Key Used to store values. [Rcl] — Recall Key Recalls values stored in registers.
8015UG-E-B 7/31/03 3:43 PM Page 5 [gal] — Gallon Key Displays and enters value as gallons. [fl oz] — Fluid Ounces Key Displays and enters value as fluid ounces. [liters] — Liter Key Displays and enters value as liters. [mL] — Milliliter Key Displays and enters value as milliliters. [%] — Percent Key Four function percent key. [tons] — Ton Key Displays and enters value as tons. [lbs] — Pounds Key Displays and enters value as pounds.
8015UG-E-B 7/31/03 3:43 PM Page 6 [Sq] — Square Key Defines a square dimension. [m] — Meters Key Displays and enters value as meters. [cm] — Centimeter Key Displays and enters value as centimeters. [mm] — Millimeter Key Displays and enters value as millimeters. [km] — Kilometer Key Displays and enters value as kilometers. [Yds] — Yards Key Displays and enters value as yards. [Feet] — Feet Key Displays and enters value as decimal feet; enters the feet portion of a feetinch value.
8015UG-E-B 7/31/03 3:43 PM Page 7 [Miles] — Miles Key Displays and enters value as miles. [SHIFT] [gal] — Gallons Per Minute Displays and enters value as gallons per minute (gpm). [SHIFT] [fl oz] — Fluid Ounces Per Second Displays and enters value as fluid ounces per second (oz/sec). [SHIFT] [liters] — Liters Per Second Displays and enters value as liters per second (liters/sec). [SHIFT] [mL] — Milliliters Per Second Displays and enters value as milliliters per second (mL/sec).
015UG-E-B 7/31/03 3:43 PM Page 8 [SHIFT] [kg] — Kilopascals Displays and enters value as kilopascals (kPa). [SHIFT] [grams] — Megapascals Displays and enters value as megapascals (MPa). [SHIFT] [Sq] — Cubic Function Defines a cubic dimension (Cu). [SHIFT] [m] — Meters Per Minute Displays and enters value as meters per minute (m/min). [SHIFT] [cm] — Meters Per Second Displays and enters value as meters per second (m/sec).
8015UG-E-B 7/31/03 3:43 PM Page 9 [SHIFT] [Inch] — Inches Per Second Displays and enters value as inches per second (in/sec). [SHIFT] [Miles] — Miles Per Hour Displays and enters value as miles per hour (mph). [SHIFT] [9] — Newton-meters Displays and enters value as newton-meters (N-m). [SHIFT] [8] — Foot-Pound Displays and enters value as foot pounds (ft-lbs). [SHIFT] [7] —Inch-Pounds Displays and enters value as inch pounds (in-lbs).
8015UG-E-B 7/31/03 3:43 PM Page 10 [SHIFT] [2] — Celsius Displays and enters value as Celsius (°C). [SHIFT] [1] — Board Feet Displays and enters value as board feet (BdFt). [SHIFT] [•] — Per Unit Function Allows you to calculate total material cost, if you multiply the total amount of material by the per unit cost of the item. [SHIFT] [–] — Change Sign Toggles the sign of the displayed value. (Positive or negative.
8015UG-E-B 7/31/03 3:43 PM Page 11 [CONV] [x] — All Clear Resets calculator to default settings. [Rcl] [x] — Metric Mode Toggle Toggles between metric mode and Imperial-English mode. Note: This mode is not reset when you perform an all clear [Conv] [x]. [Rcl] [=] — Paperless Tape Function Accesses the “Paperless Tape” mode so you can check previous entries. [Rcl] [%] — Weight Per Volume Recall Recalls the weight per volume.
8015UG-E-B 7/31/03 3:43 PM Page 12 OPERATING BASICS Power On & Off Turn the calculator on by pressing the [On/C] key. To turn the calculator off, press [Off].
8015UG-E-B 7/31/03 3:43 PM Conventions Units of Measure Area Cont’d square millimeters square inches acres Volume cubic meters cubic yards cubic miles gallons milliliters cubic centimeters cubic feet cubic inches cubic kilometers fluid ounces board feet cubic millimeters acre-feet liters Temperature Celsius Fahrenheit Weight dry ounces pounds tons grams kilograms metric tons Page 13 User’s Guide – 13
8015UG-E-B 7/31/03 3:43 PM Page 14 Conventions Units of Measure Linear Velocity feet per minute feet per second inches per second meters per minute meters per second millimeters per second miles per hour kilometers per hour Volumetric Velocity (Flow Rate) fluid ounces per second gallons per minute milliliters per second liters per second Pressure pound per square inch pounds per square foot kilopascals megapascals bars Bending Moment inch-pounds foot-pounds newton-meters 14 – Ultra Measure Mast
8015UG-E-B 7/31/03 3:43 PM Page 15 Fractional Settings When your calculator is in a default condition (battery change or full reset), it is set to round fractional values to the nearest 1/64th of an inch. However, you may program your preference for six different accuracy levels and two different modes (Normal and Fixed), all of which remain in permanent memory until revised or reset.
8015UG-E-B 7/31/03 3:43 PM Page 16 Preference Feature The Ultra Measure Master provides Preference Settings that allow you to set fractional accuracy and display features. The preference settings are displayed using [Rcl] [/]. Repeated presses of [/] toggle through the different settings while the [+] and [–] keys are used for revision. These settings remain set until they are changed or the calculator is reset.
8015UG-E-B 7/31/03 3:43 PM Page 17 FLASHING FRACTION ◆ Off (Default) ◆ On Whenever the fractional setting is other than 1/64 normal mode, a star (★) will appear in the bottom left of the display when the calculator is turned on. This indicates a special fractional setting is stored within. Setting Fractional Accuracy Keystrokes Display 1. Enter the Preference Feature [Rcl] [/] NM 1/64 (Note “1/64” flashing) 2.
8015UG-E-B 7/31/03 3:43 PM Page 18 Setting Fractional Modes NORMAL MODE In Normal Mode, the fractional result is reduced to its lowest common denominator (i.e., 8/16 reduces to 1/2). FIXED MODE In Fixed Mode, fractional results are left in the defined accuracy level (i.e., 8/16 will be shown as 8/16). Entries of higher accuracy values will temporarily override the fixed fraction setting. Using Exponential Notation Your calculator is defaulted to have exponential notation set to “on.
8015UG-E-B 7/31/03 3:43 PM Page 19 To enter an exponential value, enter the main value, press [SHIFT] [/], then enter the exponential power. Entering Exponents Enter 2.34x10-8 into the calculator. Keystrokes 2 [.] 34 [SHIFT] [/] [SHIFT] [–] 8 [=] Display 2.34 2.34 2.34–8 2.34000–08 Setting Flashing Denominator Your calculator can be set to flash the fractional denominator while fractions are entered. The flashing denominator displays the fractional accuracy level setting.
8015UG-E-B 7/31/03 3:43 PM Page 20 Basic Math Operations Your calculator uses standard chaining logic which simply means that you enter your first value, the operator (+, –, x, ÷), the second value and then the equals sign (“=”). A. B. C. D. 3 3 3 3 [+] [–] [x] [÷] 2 2 2 2 [=] [=] [=] [=] 5 1 6 1.5 This feature also makes the calculator simple to use for dimensional math.
8015UG-E-B 7/31/03 3:43 PM Page 21 4) The format of the first value you enter determines the format of the answer. However, you can use the [CONV] key to change to any format desired, provided that you maintain convention. Examples: 1) Add 7 feet 3-1/2 inches to 11 feet 4 inches: 7 [Feet] 3 [Inch] 1[/] 2 [+] 11 [Feet] 4 [Inch] [=] 18 FEET 7-1/2 INCH 2) Add 25 PSF to 12 PSI: 25 [SHIFT] [dry oz] [+] 12 [SHIFT] [lbs] [=] 1753 PSF 3) Add 14 gallons to 52 liters: 14 [gal] [+] 52 [liters] [=] 27.
8015UG-E-B 7/31/03 3:43 PM Page 22 Multiplying or Dividing Dimensions 1) You can multiply and divide two numbers when the first value entered is labeled with units of measurement and the other is just a whole number (no units of measurement). 2) You cannot multiply or divide two numbers that have different units of measurement or different conventions, except for weight and volume.
8015UG-E-B 7/31/03 3:43 PM Page 23 EXAMPLES: 1) Multiply 5 feet 3 inches by 8 feet 6-1/2 inches: 5 [Feet] 3 [Inch] [x] 8 [Feet] 6 [Inch] 1[/] 2 [=] 44.84375 SQ FEET 2) Multiply 50 meters per minute by 12.5: 50 [SHIFT] [m] [x] 12.5 [=] 625 M/M 3) Multiply 33.5 gallons by 2.031: 33.5 [gal] [x] 2.031 [=] 68.0385 GL 4) Divide 20 feet 3 inches by 9: 20 [Feet] 3 [Inch] [÷] 9 [=] 2 3 INCH 12 MPH FEET 5) Divide 30 mph by 2.5: 30 [SHIFT] [Miles] [÷] 2.
8015UG-E-B 7/31/03 3:43 PM Page 24 Percent Calculations The percent key [%] can be used to find a percentage of a number or for working add-on, discount or division percentage calculations. 355 250 25 100 [x] [+] [–] [÷] 15 6.5 5 50 [%] [%] [%] [%] 53.25 266.25 23.75 200. Memory Operation The Ultra Measure Master has ten storage registers (0 through 9). Memory 0 is a cumulative memory which operates similar to a standard [M+] key, while the other memories are used for storage only.
8015UG-E-B 7/31/03 3:43 PM Steps Page 25 Keystrokes Store to Memory x (x = 0–9) Subtract from Memory 0 [Stor] x [CONV] [Stor] [0] Recall total in Memory x [Rcl] x Recall & clear Memory 0 [Rcl] [Rcl] Clear Memory 0, (not display) [CONV] [Rcl] Replace Memory 0 [CONV] [Rcl] [Stor] [0] Clear Memory 0 thru 9 Reset calculator [Rcl] [+] [CONV] [x] How to Use Memory 0 Functions Steps Keystrokes Display Enter in memory 355 [Stor] [0] 355. Add to memory 255 [Stor] [0] 255.
8015UG-E-B 7/31/03 3:43 PM Page 26 “Paperless Tape” Feature The “Paperless Tape” feature allows the user to display the last 20 entries. While in this mode, the display looks similar to this: ↑ ↑ A B ↑ C A - the sequence number of entry (01 - 1st entry, 02 - 2nd entry, etc.) B - the math operator (+,–,x,÷,%) C - the entered or calculated value How to Use the Paperless Tape Keystrokes Display 1. Clear calculator and enter a string of numbers: [On/C] [On/C] 0.
8015UG-E-B 7/31/03 3:43 PM Page 27 2. Access the Tape function: [Rcl] [=] TTL= 22 FEET 0 INCH 3. Scroll from first value to total: [+] 01 4 FEET [+] 02+ 5 FEET [+] 03+ 6 FEET [+] 04+ 7 FEET [+] TTL= 22 FEET 0 0 0 0 0 INCH 0 0 INCH INCH INCH INCH INCH 4. Scroll to last 2 values: [–] [–] 04+ 7 03+ 6 FEET FEET INCH 5.
8015UG-E-B 7/31/03 3:43 PM Page 28 Clearing the Paperless Tape The paperless tape is cleared: 1) each time you press [On/C] [On/C] (clear); 2) each time you press [CONV] [x] (full reset/all clear); 3) when you begin entering numbers (for a new problem) after pressing the equals [=] key; 4) when you turn the unit off.
8015UG-E-B 7/31/03 3:43 PM Page 29 USING THE ULTRA MEASURE MASTER Entering Dimensions & Units When entering feet-inch dimensional values, you must enter the largest dimension first — feet before inches, inches before fractions. To enter fractions of an inch, enter the numerator (value above the line), press [/] (fraction bar key) and then enter the denominator (value below the line).
8015UG-E-B 7/31/03 3:43 PM Page 30 Linear Conversions The Ultra Measure Master can convert between these linear dimensions: ◆ Meters (M) ◆ Centimeters (CM) ◆ Millimeters (MM) ◆ Decimal Feet (FEET) ◆ Feet-Inch-fraction (FEET INCH) ◆ Decimal Inch (INCH) ◆ Yards (YD) ◆ Miles (MI) ◆ Kilometers (kM) Note: The bold letters in parentheses indicate the annunciator that displays when the unit is selected.
8015UG-E-B 7/31/03 3:43 PM Page 31 The following examples show how linear dimensions are entered: Dimension 5 Feet 1/2 Inch 5 Feet 1-1/2 Inch Keystrokes 5 [Feet] 1 [/] 2 5 [Feet] 1 [Inch] 1 [/] 2 10 Yards 10 [Yds] 17.5 Meters 17.5 [m] Any units of measurement other than inches must be entered as whole values (5 yards) or decimal values (5.5 meters), and not in combination with feet and inches or with themselves. For example, you cannot enter 12 meters 6 centimeters 4 millimeters.
8015UG-E-B 7/31/03 3:43 PM Page 32 Convert 27 feet to other linear dimensional formats. Step/Keystrokes Display 1. Enter 27 feet: 27 [Feet] 27 FEET 2. Convert to inches: [CONV] [Inch] 324 INCH 3. Convert to yards: [CONV] [Yds] 9 YD 4. Convert to meters: [CONV] [m] 8.2296 M 5. Convert to km: [CONV] [km] 0.00823 KM 0.005114 MI 6.
8015UG-E-B 7/31/03 3:43 PM Page 33 Convert 65 meters to other linear dimensions. Steps/Keystrokes Display 1. Enter 65 meters: 65 [m] 65 M 2. Convert to cm: [CONV] [cm] 6500 CM 71.08486 YD 0.040389 MI 3. Convert to yards: [CONV] [Yds] 4.
8015UG-E-B 7/31/03 3:43 PM Page 34 Area Conversions Your calculator can convert the following area dimensions: ◆ Square Meters (SQ M) ◆ Square Yards (SQ YD) ◆ Square Miles (SQ MI) ◆ Hectares (HECT) ◆ Square Centimeters (SQ CM) ◆ Square Feet (SQ FEET) ◆ Square Kilometers (SQ kM) ◆ Square Millimeters (SQ MM) ◆ Square Inch (SQ INCH) ◆ Acres (ACRE) Note: The letters in parentheses indicate the annunciator that displays when the units are selected.
8015UG-E-B 7/31/03 3:43 PM Page 35 Note: You do not have to use the [Sq] square key to convert to other square units of value; the calculator automatically converts to a square unit of value.
8015UG-E-B 7/31/03 3:43 PM Page 36 EXAMPLES: Convert 1.25 acres to other area dimensions: Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 1.25 acres: 1.25 [SHIFT] [5] 1.25 ACRE 3. Convert to sq feet: [CONV] [Feet] 54450 SQ FEET 4. Convert to sq yards: [CONV] [Yds] 6050 SQ YD 5. Convert to meters: [CONV] [m] 5058.571 SQ M Convert 252 square meters to other area dimensions: Steps/Keystrokes Display 1. Enter 252 sq m: 252 [Sq] [m] 252 SQ M 2.
8015UG-E-B 7/31/03 3:43 PM Page 37 3. Convert to sq yards: [CONV] [Yds] 301.3895 SQ YD 4. Convert to hectares: [CONV] [SHIFT] [4] 0.
8015UG-E-B 7/31/03 3:43 PM Page 38 To convert a volume value on your display, press the [CONV] key and then the keystrokes for the volume dimension to convert it to (for example, [CONV] [cm] to convert to cubic centimeters). Note: When converting volume dimensions, you do not have to use the [SHIFT] [Sq] cubic function to convert to other cubic units of value; the calculator automatically converts to a cubic unit of measurement.
8015UG-E-B 7/31/03 3:43 PM Page 39 EXAMPLES: Convert 45.75 board feet to other volume dimensions. Steps/Keystrokes Display 1. Clear calculator: [On/C] [On/C] 0. 2. Enter 45.75 board feet: 45.75 [SHIFT] [1] 45.75 B FEET 3. Convert to cubic feet: [CONV] [Feet] 3.8125 CU FEET 4. Convert to cubic yards: [CONV] [Yds] 0.141204 CU YD 5.
8015UG-E-B 7/31/03 3:43 PM Page 40 Find the volume of a rectangular container 3 feet by 1 foot 9-5/8 inches by 2 feet 4 inches then convert to centimeters and yards. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter length and multiply by width and depth: 3 [Feet] [x] 1 [Feet] 3 FEET 9 [Inch] 5[/]8 1 - 9 5/8 FEET INCH [x] 2 [Feet] 4 [Inch] [=] 12.61458 CU FEET 3. Convert to Cu Cm: [CONV] [cm] 357205.2 CU CM 0.467207 CU YD 4.
8015UG-E-B 7/31/03 3:43 PM Page 41 Convert 126 liters to other volume dimensions. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 126 liters: 126 [liters] 126 L 3. Convert to gallon: [CONV] [gal] 33.28568 GL 4. Convert to fluid oz: [CONV] [fl oz] 4260.
8015UG-E-B 7/31/03 3:43 PM Page 42 Note: The letters in parentheses indicate the annunciator that displays when the units are selected. To convert a weight value on your display, press the [CONV] key, then the keystrokes for the weight unit to which you want to convert. Units Keystrokes D-OZ [dry oz] LB [lbs] Ton [tons] GRAM [grams] kG [kg] MET Ton [SHIFT] [tons] EXAMPLES: Convert 150 pounds to kilograms. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 2.
8015UG-E-B 7/31/03 3:43 PM Page 43 If your car has a 12 gallon tank, how many liters of gas will it take to fill it? What is the cost if 1 liter is $0.75? Use the per unit function to find the total cost of the gas. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 2. Enter 12 gallons: 12 [gal] 0. 12 GL 3. Convert to liters at $0.75 per liter: [CONV] [liters] 45.42494 L [x] .75 [SHIFT] [•] $ 34.07 PER You have received a shipment of 23,000 kg of fill.
8015UG-E-B 7/31/03 3:43 PM Page 44 Weight/Volume Conversions The Ultra Measure Master can convert between weight and volume. The default weights per volume factor is: ◆ 1.5 tons per cubic yard ◆ 3000 lbs per cubic yard ◆ 111.1111 lbs per cubic feet ◆ 1.779829 metric tons per cubic meter ◆ 1779.829 kg per cubic meter ◆ 1.779829 grams per cubic centimeter To recall weight per volume factor press [Rcl] [%]. Continue pressing [%] to display as pounds or kilograms.
8015UG-E-B 7/31/03 3:43 PM Page 45 EXAMPLES: Find the total volume of concrete needed to pour five 24 inch by 12 inch footings, each 2 feet deep. Then find the weight of the concrete (use the default weight factor of 1.5 tons per cubic yard). Steps/Keystrokes Display 1. Clear Calculator: [On/C] [On/C] 0. 2. Enter weight per cubic yard: 1.5 [SHIFT] [%] 1.5 Ton Per CU YD Step 1 — Find Volume for One Footing 3.
8015UG-E-B 7/31/03 3:43 PM Page 46 Find the weight of 15 cubic yards at 1.75 tons/cu yd, & convert to other weights. Steps/Keystrokes Display 1. Enter 1.75 factor: 1.75 [SHIFT] [%] 1.75 TON PER CU YD 2. Enter15 cu yds: 15 [SHIFT] [Sq] [Yds] 15 CU YD 3. Convert to lbs then kg: [CONV] [lbs] [CONV] [kg] 46 – Ultra Measure Master ® 52500 LB 23813.
8015UG-E-B 7/31/03 3:43 PM Page 47 Temperature Conversions To convert a displayed temperature value, press [CONV] then the keystrokes for either Fahrenheit or Celsius. Units Keystrokes °C °F [SHIFT] [2] [SHIFT] [3] EXAMPLES: Convert 78 °F to a °C temperature. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 78 °F and convert to Celsius: 78 [SHIFT] [3] [CONV] [SHIFT] [2] 78 °F 25.55556 °C Convert 11 °C to a °F temperature. Steps/Keystrokes Display 1. Clear Calculator.
8015UG-E-B 7/31/03 3:43 PM Page 48 Linear Velocity Conversions The Ultra Measure Master can convert between the following linear velocities: ◆ Feet per minute (FPM) ◆ Feet per seconds (FPS) ◆ Inch per second (IPS) ◆ Meters per minute (M/M) ◆ Meters per second (M/S) ◆ Millimeters per second (MM/S) ◆ Miles per hour (MPH) ◆ Kilometers per hour (KM/H) Note: The letters in parentheses indicate the annunciator associated with the unit.
8015UG-E-B 7/31/03 3:43 PM Page 49 To convert a linear velocity on your display, press the [CONV] key and then the keystrokes for the linear velocity to convert it to. EXAMPLES: Convert 55 MPH to kilometers per hour. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 55 mph then convert to kmh: 55 [SHIFT] [Mile] 55 MPH [CONV] [SHIFT] [km] 88.51392 KM/H Convert 8 inches per second (IPS) to millimeters per second (mm/s). Steps/Keystrokes Display 1. Clear Calculator.
8015UG-E-B 7/31/03 3:43 PM Page 50 Volumetric Velocity Conversions This calculator can convert between the following volumetric velocities: ◆ Fluid ounces per second (OPS) ◆ Gallons per minute (GPM) ◆ Milliliters per second (ML/S) ◆ Liters per second (L/S) Note: Letters in parentheses represent the annunciator associated with the unit. When the unit is selected, the annunciator appears on the display screen.
8015UG-E-B 7/31/03 3:43 PM Page 51 EXAMPLES: Convert 48 fluid ounces per second to liters per second. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 48 oz/s then convert to l/s: 48 [SHIFT] [fl oz] 48 OPS [CONV] [SHIFT] [liters] 1.419529 L/S An aqueduct should be sloped so that water travels less than 10 feet per minute. After a heavy rainfall, the water traveled at an approximate velocity of 1.72 inches per second.
8015UG-E-B 7/31/03 3:43 PM Page 52 The faucet in a house should provide 4.5 gallons of water per minute. If you have a 2 liter bottle that filled up in 12 seconds, is the faucet within code? Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Divide liters/sec: 2 [÷] 12 [=] 0.166667 3. Enter as liters/sec.: [SHIFT] [liters] 0.166667 L/S 4. Convert to gal/min: [CONV] [SHIFT] [gal] 2.
8015UG-E-B 7/31/03 3:43 PM Units Keystrokes PSI [SHIFT] [lbs] PSF [SHIFT] [dry oz] kPA [SHIFT] [kg] MPA [SHIFT] [grams] Page 53 The following examples show how to convert a pressure value. EXAMPLES: A water line is reading a pressure of .5 psi, what would the pressure be in psf, kpa and mpa? Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter psi .5 [SHIFT] [lbs] 0.5 PSI 72 PSF 3.447379 KPA [CONV] [SHIFT] [grams] 0.003447 MPA 3.
8015UG-E-B 7/31/03 3:43 PM Page 54 Convert 24 pounds per square foot to kilopascals. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter 24 psf: 24 [SHIFT] [dry oz] 24 PSF 1.149126 KPA 3. Convert to kpa: [CONV] [SHIFT] [kg] Bending Moment Conversions The calculator can convert between the following bending moment units: Note: The letters in parentheses indicate the annunciator that displays when the units are selected.
8015UG-E-B 7/31/03 3:43 PM Page 55 To convert a bending moment value on your display, press the [CONV] key and then the keystrokes for the bending moment value to convert it to. EXAMPLES: Convert 120 inch-lb to newton-meters. Steps/Keystrokes Display 1. Enter 120 in/lb: 120 [SHIFT] [7] 120 LB INCH 2. Convert to N-m: [CONV] [SHIFT] [9] 13.55818 N-M Convert 700 newton-meters to ft-lb. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter N-m: 700 [SHIFT] [9] 700 N-M 3.
8015UG-E-B 7/31/03 3:43 PM Page 56 Your metric-based plan says that the bridge rail bolt must be tightened to 30 n-m but your torque wrench only shows ft-lb. Find the ft-lb setting required to set up the wrench. Steps/Keystrokes Display 1. Clear Calculator. [On/C] [On/C] 0. 2. Enter N-m: 30 [SHIFT] [9] 30 N-M 3. Find ft/lbs: [CONV] [SHIFT] [8] 22.
8015UG-E-B 7/31/03 3:43 PM Page 57 APPENDIX Accuracy/Errors Accuracy/Display Capacity — Your calculator has an eleven digit display. This is made up of seven digits (normal display) and four digits for the fraction. In a standard calculation, each calculation is carried out internally to 10 digits and rounded to a 7-digit standard display. A 5/4 rounding technique is used to add 1 to the least significant digit in the display if the next non-displayed digit is five or more.
8015UG-E-B 7/31/03 3:43 PM Page 58 “10,000,000 mm” cannot be displayed because it is out of the 7-digit display, so “10,000 m” will be displayed instead. This auto-ranging also applies to other dimensional units, such as inches to feet, and feet to yards, etc. Battery Information Your calculator is powered by a single 3-Volt Lithium CR-2032 battery. This should last upwards of 800 hours of actual use (1 year plus for most users). Should the display become very dim or erratic, replace the battery.
8015UG-E-B 7/31/03 3:43 PM Page 59 WARRANTY REPAIR SERVICE — USA Calculated Industries, Inc. (“CII”) warrants this product against defects in materials and workmanship for a period of one (1) year from the date of original consumer purchase in the U.S. If a defect exists during the warranty period, CII at its option will either repair (using new or remanufactured parts) or replace (with a new or remanufactured unit) the product at no charge.
8015UG-E-B 7/31/03 3:43 PM Page 60 the contiguous 48 states. (Outside the contiguous 48 states, please call CII for return shipping costs.) A repaired or replacement product assumes the remaining warranty of the original product or 90 days, whichever is longer. NON-WARRANTY REPAIR SERVICE — USA Non-warranty repair covers service beyond the warranty period or service requested due to damage resulting from misuse or abuse.
8015UG-E-B 7/31/03 3:43 PM Page 61 DISCLAIMER CII MAKES NO WARRANTY OR REPRESENTATION, EITHER EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCT’S QUALITY, PERFORMANCE, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. AS A RESULT, THIS PRODUCT, INCLUDING BUT NOT LIMITED TO, KEYSTROKE PROCEDURES, MATHEMATICAL ACCURACY AND PREPROGRAMMED MATERIAL, IS SOLD “AS IS,” AND YOU THE PURCHASER ASSUME THE ENTIRE RISK AS TO ITS QUALITY AND PERFORMANCE.
8015UG-E-B 7/31/03 3:43 PM Page 62 FCC CLASS B This equipment has been certified to comply with the limits for a Class B computing device, pursuant to Subpart J of Part 15 of FCC rules. Looking for New Ideas Calculated Industries, a leading manufacturer of special function calculators and digital measuring instruments, is always looking for new product ideas in these areas.
8015UG-E-B 7/31/03 3:43 PM Page 63 How To Reach CII Headquarters Mail Calculated Industries, Inc. 4840 Hytech Drive Carson City, NV 89706 USA Phone 1-775-885–4900 Fax 1-775-885–4949 Email techsup@calculated.com World Wide Web http://www.calculated.
8015UG-E-B 7/31/03 3:43 PM Page 1 ULTRA MEASURE MASTER® and CALCULATED INDUSTRIES® are registered trademarks of Calculated Industries, Inc. ©2003. ALL RIGHTS RESERVED Software copyrighted and licensed to Calculated Industries by Construction Master Technologies, LLC, 2003.
