Owner`s manual

C. Maintaining the proper level of bromine during use is extremely important.
D. If the bromine level is too low, bacteria and viruses can grow rapidly in the warm water.
E. If the bromine level is too high, the water can cause discomfort to the user’s eyes, lungs and skin. Simply allow some time to pass in order for the bromine to
dissipate.
F. When the bromine level is within the recommended range, the spa is ready to be enjoyed.
DO’S AND DON’TS
DO check your bromine chemical level prior to each use.•
DO chenage the SPA FROG mineral cartridge every 4 months.•
DO test Total Alkalinity and pH weekly.•
DOuseMonarchMPS+non-chlorine(Pmonpersulfate)oxidizerforspaonly.•
DO store all chemicals in a tightly sealed contriner in a cool, dry place.•
DON'T use sodium bromide or biguanides. These are an active sanitizer and will combine with the silver ions to inactivate them.•
DON'T use a water clarifier; Clarifiers will cause the spa water to become cloudy.•
DON'T use the Monarch silver cartridge with SPA FROG.•
SUPER CHLORINATION
Super Chlorination is a process used to eliminate chlorine smell (if you are using chlorine) by “burning-off” chloramines (used chlorine). This helps maintain the
proper level of free chlorine.
When giving your water a super chlorination treatment, open the cover at least half way for twenty minutes to allow the chlorine
gas to vent off. The high concentration of chlorine gas which may exist as a result of super chlorination (not daily sanitation)
may eventually cause discoloration or degradation to the bottom of the cover, which would not be covered under the terms of
your warranty.
WARNING : There are several forms of stabilized chlorine available for use in spas and swimming pools. Each form has
specific chemical characteristics. It is extremely important that the form you choose is specifically designed for use in spas.
Use of an incorrect product such as tri-chloro, which has a very low pH (2.6), dissolves too quickly in hot water resulting in
extremely high levels of chlorine, and is designed for concrete or plaster swimming pools, WILL cause damage to your spa.
Use of a liquid, or any type of compressed bromine or chlorine, acid, or any type or sanitizer which is not recommended by
Watkins Manufacturing Corporation, WILL damage your spa and is specifically not covered under the terms of the limited
warranty.
IMPORTANT: Granulated chlorine (sodium dichlor) will degrade if stored improperly. We recommend purchasing chlorine in
one, two, or five pound containers and storing it in a cool, dry place to maintain its potency.
WARNING : Never leave an open spa unattended, especially if there are children present!
SUPPLEMENTAL WATER MAINTENANCE
Proper water sanitation and mineral balance (pH control) are absolutely essential for a complete spa water maintenance program. Here are two other popular water
additives that are optional:
1. Mineral Deposit Inhibitors
As water evaporates from your spa and new water is added, the amount of dissolved minerals will increase. (Minimize evaporation by keeping the cover on the spa
whenever possible.) The spa water may eventually become “hard” (Calcium Hardness too high) enough to damage the heater by calcifying its surface. Proper pH control
can minimize this.
Normal soap build-up will require water replacement regularly enough that mineral deposits normally are not a problem.
Occasionally, high iron or copper content in the water may produce green or brown stains on the spa. A stain and scale inhibitor may help to reduce these metals.
NOTE: Well water may contain high concentrations of minerals. The use of a low water volume, extra-fine pore water filter will help to remove many of the larger particles
during the filling of the spa.
2. Foam Inhibitors
Spa water requires changing due to the buildup of soap in the water. Typically, soap will cause the spa water to foam when the jets are used. Soap is introduced into the
spa water from two sources: users’ bodies, which retain a soap residue after showering, and swimming apparel, which retains soap after washing.
Foam inhibitors can suppress foam, but cannot remove soap from the water. Soap is very difficult to remove from the water because soap is not oxidized by any
chemical added to the spa. Only ozone can oxidize soap.
Eventually the soap build-up in the water will be concentrated, resulting in an unclean feeling on the bather’s skin, which is impossible to remedy. When this occurs, it’s
time to drain and refill the spa. Depending on the soap input, the water should last about 4 months before needing to be drained.
WATER QUALITY AND MAINTENANCE
19