RMD 80 1 BT MANUAL • GB •
CONTENTS Safety Precautions......................................................................................................2-3 Installation..................................................................................................4-5 Wiring Connections......................................................................................................6-7 Basic Operation...............................................................................................................
SAFETY PRECAUTIONS Important Warnings to Take Note of BEFORE Commencing Installation Damage Caused By Incorrect Installation or Usage is NOT Covered By Warranty. PLEASE Take the Time to Read the Installation Notes Carefully. To Validate the Warranty Please Ensure That the Unit is Installed by a Professional, VAT registered Car Audio Installation Company. To avoid short in your vehicles electrical system, be sure to disconnect the battery cable before beginning installation.
SAFETY PRECAUTIONS Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. To avoid short-circuiting, cover all disconnected lead with insulating tape. There is a possibility of short-circuiting if the leads are not insulated. Route and secure all wiring so it cannot touch any moving parts, such as the gear lever and handbrake. Do not route wiring in places that get hot, such as near the heater outlet.
INSTALLATION Tools for Installation Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and supplies may also be needed for the installation: Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires The above are not supplied.
INSTALLATION WARNING! Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery. NOTE: Remove the two transport screws from the top of the unit before installing. NOTE: Make sure there is enough space for the installation of this double-din unit.
WIRING DIAGRAM DTV Antenna (optional) TV Antenna (optional) GPS Antenna (optional) Radio Antenna HDMI (optional) Reverse(purple-white) Parking (green) IPOD(optional) Steering 1 (brown) Steering 2A (white) Steering 2B (grey) Connector A 1. Rear right speaker(+)/Purple 2. Rear right speaker(-)/Purple-Black 3. Front right speaker(+)/Grey 4. Front right speaker(-)/Grey-Black 5. Front left speaker(+)/White 6. Front left speaker(-)/White-Black 7. Rear left speaker(+)/Green 8.
WIRING DIAGRAM General Wiring Notes: Make sure You have a good chassis ground. Good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the .vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good ground connection. Black Ground Connect to vehicle body/chassis. Make sure you have a good chassis ground.
BASIC OPERATION 1. Turning the unit On / Off Press the Power Button to turn the unit on. When the unit is on, press the Power Button once to turn the TFT off. During TFT off, the video out signal will be available so that the connected monitor will show the screen of the unit. Press the Power Button again to turn the TFT back on. Press and hold the POW button again to turn the unit off. 2. Mode Selection Press the MODE Button to cycle the Play Modes between RADIO, USB, SD and AUX in. 3. Sound Control A.
Radio Operation 1. Choose Radio Band Touch the BAND button onscreen to choose among the five radio bands - three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations. 2. Radio Seek Function In Radio Mode, touch and hold >> or << Button to adjust the radio frequency automatically. Press the button once to adjust the radio frequency manually. 3.
TV Operation (Optional) SCAN Tap SCAN to seek all strong and clear frequency stations available and store them. Press << or >> to seek one station. SAVED STATIONS When you reach the desired TV stations, the stations will be automatically saved for you to recall later. SELECT SAVED STATIONS Tap the < or > Buttons to select the saved stations up or down. GOTO Tap the GOTO button on the bottom menu, then you will enter a screen for you to input the exact frequency of TV station.
Bluetooth Operation (Optional) PAIRING At BT mode, search bluetooth device by the phone and “JZS-HHB” will appear in your phone. Input “0000” as password to establish connection. DIAL PAD Touch the dial pad to dial the number you would like to call. Touch the CALL (green) button to send the number. CALL RECORD Press the HISTORY button to enter the phone book page to view received, missed and dialed calls. More details in the next page.
USB/SD Operation Plug the USB/SD card into the USB/SD port. The unit will play the contents automatically. 1. Advance / Go Back Advance to the next track or go back to the previous track by pressing the forward or rewind buttons on the front panel or touch screen. 2. Play/Pause Press the play/pause button to pause the playback or resume. 3. Fast Forward/Fast Rewind Press and hold the forward or rewind icons on the touch screen during audio playback.
Steering Wheel Control Refer to the wiring diagram for connection. The brown wire (Steering 1) must be connected, then the white or grey (Steering 2A and 2B) will be connected depending on the total number of the wire from the steering wheel remote control of your vehicle. TAB STEERING WHEEL LOGO in the OSD. Press RESET before the set up. Select from the 10 functions according to the number of available keys on the steering wheel of your vehicle.
Other Operations 1. GPS Navigation (Optional) If GPS navigation is available with the system, Tap the GPS logo on the OSD to enter GPS navigation. Follow the on screen instruction to input destination and start navigation. The operation varies from software to software. 2. IPOD Input (Optional) This unit can support IPOD Input. Use the IPOD wire (supplied) to connect your IPOD with this car stereo. Select IPOD on the main user interface.
MAINTENANCE Cleaning the Unit Do not use any liquids to clean this unit. Do not use petroleum distillates to clean this unit. Use a clean, dry cloth to clean this unit. Replacing the Fuse Make sure the amperage matches the specified value when replacing the fuse(s). If the fuse is bad, check the power connection and replace the fuse with a new one. If the same problem occurs, this might indicate a malfunction within the unit.
Infra Red Remote Control (Optional) 1. Power On/off 2. Mode Switch Button 3. Stop Playback 4. Navigation Up 5. Navigation Left 6. Enter Button 7. Change The Audio Output Method 8. Navigation Down 9. Band/Select Type 10. Auto Preset Scan/Repeat Play 11. Tuning/Music Selection (numeric key) 12. Mute Sound Button RATIO 13. Time Clock Display/Statistical Disc Information Display Button 14. VOL + 15. Play/Pause Function 16. Sound Select Button 17. Navigation Right 18. VOL 19.
SIMPLE TROUBLESHOOTING GUIDE PROBLEM CAUSE / SOLUTION No Power Check whether the fuse is blown, replace with fuse of proper value if necessary. Unit stops responding or shows error Press the RESET button. in display Unable to receive radio stations Check whether the antenna is inserted or the antenna is properly connected; if not, insert the antenna or connect it properly. Poor effect on receiving a station -Antenna may not be of the proper length.
Specifications GENERAL Operating Power.......................................................................................................................................12 Volts DC, Negative Ground Output Wiring...............................................................................................................................Designed for using four speakers only RCA line out........................................................................................................................
