INSTRUCTION MANUAL MODEL NO.
Important Safety Information End user must read this section before operating this unit. Operation of the unit is permitted only if traffic conditions are suitable and you are absolutely sure that you, your passengers or other motorists are not endangered, obstructed or inconveniienced. In all cases, all applicable road traffic regulations must be obeyed. DESTINATIONS MAY ONLY BE ENTERED WHEN THE VEHICLE IS STATIONARY. The navigation system is only an aid.
Connecting the System Important notes Do not route wires where they will be exposed to high temperatures. If the insulation heats up, wires may become damaged, resulting in a short circuit or malfunction and permanent damage to the navigation system. Do not cut the GPS aerial cable to shorten it or use an extension to make it longer. Altering the aerial cable could result in a short circuit or malfunction. Do not shorten any leads.
Connecting the System About Parking Wire Caution: In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching moving video while driving. Park your car in a safe place and engage the "parking brake" before watching moving video.
Connecting the System Wiring Diagram - Audio / Video Connections GPS AERIAL BLUE SUB WOOFER SUB-WOOFER OUTPUT Note: Please refer to the "Installing the GPS Aerial". For the proper mounting or installation of this GPS AERIAL.
Connecting the System Wiring Diagram - Power / Speakers FUSE (Not supplied) ANTENNA EXTENDER CABLE ANTENNA JACK BLACK FRONT CHANNEL BLUE/WHITE STRIPE RED YELLOW POWER AMPLIFIER REMOTE RED R-CH L-CH WHITE AMP WHITE L-CH REAR CHANNEL (Not supplied) RCA-TO-RCA CABLES RED R-CH GREY (RED) Ignition wire (ACC) (YELLOW) Battery wire (B+) 20-PIN AUDIO/POWER HARNESS (See Figure 1 ) Connect to power amplifier, If not used, Tape bare end of wire.
Installing the GPS Antenna / Aerial Parts Supplied Setting Description GPS aerial Metal sheet Clamp (5 pcs.) Waterproof pad When installing the aerial inside the vehicle (on the rear shelf) Affix the metal sheet on as level a surface as possible where the GPS antenna / aerial faces the window. Place the GPS antenna / aerial on the metal sheet. (The GPS antenna / aerial is fastened with its magnet.) Metal Sheet GPS anteanna / aerial Peel off the protective sheet on the rear.
Installing the GPS Antenna / Aerial End user must read this section before installing the GPS Antenna / Aerial. Caution: Do not cut the GPS antenna / aerial lead to shorten it or use an extension to make it longer. Altering the aerial cable could result in a short circuit or malfunction and permanent damage to the navigation system. Connecting the GPS Antenna / Aerial to the unit SCREW 5M GPS AERIAL GPS AERIAL Note: Always use the provided screw to fasten the GPS Antenna / Aerial.
Installing the GPS Antenna / Aerial Take care not to pull the antenna / aerial lead when removing the GPS aerial. The magnet attached to the aerial is very powerful and the lead may become detached. The GPS antenna / aerial is installed with a magnet. When installing the GPS antena / aerial, be careful not to scratch the vehicle body. When installing the GPS antenna / aerial on the outside of the vehicle, always put it in the vehicle when going through an automatic vehicle wash.
Installation the Unit Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions or permanent damage to the unit. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Installation the Unit 1 2 182 53 3 No. 1 2 3 4 5 6 7 Content Dashboard Nut (5mm) Spring washer Screw (4X12mm) Screw Support Strap Be sure to use the support strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle Plain washer 1 6 7 4 2 5 3 Removing the unit No. 1 2 3 Content Frame Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove down wards and attach it.
Installation the Unit 1 2 3 Trim Plate Installation Push the trim plate against the chassis until it is fitted. You must do this before you install the front panel, otherwise it can't be attached. Din rear-mount (method B) Installation using the screw holes on the sides of the unit.Fastening the unit to the factory radio mounting bracket. No.
Detachable Front Panel (D.F.P.) Removing the detachable front panel (D.F.P.). RELEASE BUTTON D.F.P. 1. Turn the Power off. 2. Press the Panel Release Button. 3. Remove the D.F.P. Attaching the detachable front panel (D.F.P.) 1. Insert the right side of the D.F.P. Into the main unit. 1. 2. PU SH T-Joint Note: The D.F.P. Must be attached into the T-Joint. 2. Press the D.F.P. on to the left side of middle of D.F.P. until a " click" sound is heard. Caution: Do not insert the D.F.P from the left side.
Panel Open / Close Operation The unit is equipped with the most advanced full logic motorized slide down system.You can enjoy the advance technology with a single press of the " Eject / Open" button. Please read carefully the following operation instruction before operating the unit. Open / close the panel Press the " Eject / Open" button to slide down (Eject / Open) closed panel or to slide up (close) an opened panel. Loading a CD Panel in the slide down position, the disc slot become accessible.
Overview the Unit Front panel main control Panel Release Eject / Open Panel Angle adjust IR Receiver RE L MODE 4 RD 1 M LOUD 2 5 SU RP BW 6 3 OSD SET UP T AS PS BAND 4x75WATT TA MCD 795 GPS MODE MUTE Volume Knob Touch Screen Display USB SD Card slot for MEDIA PLAYER 2 1 Detach the Front Panel Face Up Insert the Memory Card with Label up side into the SD Card slot on main unit SD Card slot for DIGITAL MAP or SOFTWARE UPGRADE Detach the Front Panel 1 2 Insert the Memory Card wit
Disc Can Supports Discs can play with this unit No. Content 1 Digital Versatile Discs (DVDs) 2 Video CDs (VCDs) 3 Digital Versatile Discs Recordable(DVD+/-R) 4 Digital Versatile Discs Rewritable(DVD+/-RW) 5 6 Compact Digital Video (VCD) Compact Discs (Cds) 7 CD Recordable (CD-R) 8 CD Rewritable (CD-RW) Discs which can not be played 8 cm Disc CDV, CDI, CDG, LD DVD RAM Disc maintenance Note on region code ALL DVD players and DVD Video discs have their own Region Code numbers.
Formats Can Playback Audio format can playback Playback CD-DA and MP3 or WMA digital music file on CD-ROM or DVD-ROM or USB or Memory Card. Note of MP3 and WMA: Support Maximum 2000 files. Maximum 30 characters display. Supported Sampling frequencies; 32kHz, 44.1kHz, 48kHz. Supported Bit-Rates: MP3=8 ~320kbps variable bit rate; WMA = 32 ~ 192kbps variable bit rate. Video format can playback 2 Playback IMAGE JPEG, DVD Video, AVI, MPEG4. on CD-ROM or DVD-ROM or USB or Memory Card.
Remote Control Operations 9 12 M UT E 1 2 8 10 SRC 5 11 VOLUME 15 4 16 6 17 13 14 3 AUDIO 18 30 37 34 31 19 38 20 21 GOTO 39 35 24 22 36 32 25 7 AF TA LOUD GPS MODE 27 NAVI VOICE 33 40 29 23 28 26 OPERATIONS: SYSTEM KEY 1 2 3 Short Press Long Press Mute Power Open & Close Audio Menu System Menu 4 Source 5 Volume Up 6 Volume Down 7 Loud TUNER Short Press Angle CD MP3 DVD Long Press Short Press Long Press Short Press Long Press Short Press
Remote Control Operations 9 12 M UT E 1 2 8 10 SRC 5 11 VOLUME 15 4 16 6 17 13 14 3 AUDIO 18 30 37 34 31 19 38 20 21 GOTO 39 35 24 22 36 32 25 7 AF TA LOUD GPS MODE 27 NAVI VOICE 33 40 29 23 28 26 OPERATIONS: SYSTEM KEY Short Press Long Press TUNER Short Press 23 M5 24 M6 25 26 27 28 29 Band NAVI Voice Volume Long Press Memory 5 Memory 6 DVD CD/MP3/WMA Short Press Long Press Track NO. Access File NO. Access Track NO. Access File NO. Access Track NO.
General Operations 4 96 5 3 REL MODE Main Menu 4 RD 1 M LOUD 2 5 Media Player Tuner AV-In SU RP BW 6 3 GPS OSD SET UP T Setting AS PS BAND MCD 795 4x75WATT TA GPS MODE MUTE 1 1 2 7 8 Power On / Off Button Long press the POWER button for more than 3 seconds or short press any other button on the front of the panel (except the Eject / Open) to turn on the unit. Long press the POWER button for more than 3 seconds to turn Off the unit.
General Operations 3 Panel Angle Adjustment End user can adjust the panel viewing angle of the display to obtain the optimum viewing angle inside the vehicle There are TWO angles can be adjusted by Long pressing the panel Eject / Open button: 1)1st long press to get into Angle 1 2)2nd long press to get into Angle 2 3)3rd long press to resume to the normal position 4 Panel Release Button Press this button to remove detach the control panel. 5 Main Menu Screen Starts by displaying the Main Menu.
General Operations 7 Sub-woofer Short press the SUB-W button for less than 3 seconds to turn on the Sub-woofer function. Press the SUB-W button again to turn off the Sub-woofer function. 8 GPS Mode End user can switch the TFT display between the playback mode and GPS NAVIGATION / MAP screen by following: 1. Short pressing the GPS MODE button on panel. 2. Tapping on the touch screen button NAVI or . AF FM1 10:30 am Band 9 104.00 FMSELECT 87.50 90.00 98.00 106.00 108.00 87.
Tuner operations 4 2 96 3 5 REL MODE Main Menu 4 RD 1 M AF GPS FM1 LOUD 2 5 FMSELECT Tuner 87.50 SU RP BW 6 3 10:30 am T Band Media Player 104.00 106.00 90.00 Setting 108.00 AV-In 98.00 OSD SET UP AS PS 87.50 BAND 4x75WATT TA MCD 795 GPS MODE MUTE 2 3 1 1 7 Band Function 1 4 Press panel BAND button or touch screen between FM bands and AM(MW) bands.
Tuner operations RDS Function The unit is equipped with the following RDS function: - 6 AF Alternative Frequencies CT Clock Time PI Program identifications PS Program service name PTY Program Type REG Regional Change TA Traffic Announcement TP Traffic program AF function Short pressing panel AF button less than 3 seconds to select AF ON / OFF. " AF" icon will light up on the screen.
Tuner operations 7 PTY Function Long press the SUB-W / PTY button for more than 3 seconds to set into the PTY mode. And then press this button repeatedly to different PTY group as listed below. Once the desired PTY is shown on the preset memory M1 to M6, press this preset memory number to activate the searching of this PTY, the PTY name will appear on the 6 preset buttons.
Media Player This Multi-Media player unit can support the playback of CD Disc, DVD disc, USB Host, SD Memory Card. Note: For more details of this unit supporting playback disc and format. Please see pages of "Disc Can support" & " Format can playback" . Caution: In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching moving video while driving. Park your car in a safe place and engage the " parking brake" before watching moving video.
Media Player Note: If any media device is not avaiable in this unit, this media souurce will not appear during Mode switch or on the touch screen. Note: This unit only can playback the SD Card which is inserted in the main unit. Please refere to the page "Overview of the unit" for more details of the SD card slot for media player use. Color setting during DVD video disc playback Tapping touch screen button to access into the DVD video color setting.
Media Player Navigation While Media Player Playback Navigation Voice Guidance on or off under Media Player playback This unit will automacitally MUTE the audio output of the Media player when there is announcement from the navigation voice guidance. This function can be activated or deactivated by NAVI .
Media Player CD/VCD Disc Operation 1 7 4 RE L MODE NAVI NAVI VOICE 4 RD 1 M LOUD 2 5 SU RP BW 6 3 OSD SET UP T AS PS BAND MCD 795 4x75WATT TA GPS MODE MUTE 2 3 8 8 1 2 7 Track / File Press the TRACK / FILE UP (7) / TRACK / FILE DOWN (8) button or touch screen (7) / (8) for less than 1 second to move to the next or previous track on the CD. The selected track number will appear on the screen.
Media Player 2 Stop Function Press STOP button or tap touch screen button to stop playing.When playback is stopped,the unit can keep the memory of where the STOP was pressed. Press PLAY and the playback will resume from this point. Press STOP button again, RESUME function will be cancelled and the unit is now in full stop mode. If PLAY button is pressed now, it will play from the beginning. RESUME function is suitable for discs showing playing time during playback.
Media Player PBC ( On remote control ) Press PBC button on remote control to choose a VCD disc play mode:PBC_ON or PBC_OFF,when you playing a VCD disc. When pressing PBC button and the player change to PBC _ON playing mode, a PBC list of the disc will be displayed on TV or monitor. In PBC list, use number button to select a track to play or direction press PLAY button to start to the playback.
Media Player Music / Image / Video File Playback Operation The following display information will appear, if a Multi-Media disc or USB or SD is inserted into this unit.
Media Player Note: Other operation are the same as CD / VCD, like repeat, program and so on. Please refer to the CD / VCD Disc Operation section. 10&11 Up / Down / Right / Left / Enter Press on remote control or tap touch screen / / / button to move the cursor. Press OK button on remote control or tap touch screen button to confirm the selection.
Media Player MMN->IMAGE View-> Slide In Slide mode, when the key " ENTE" or " PLAY" is pressed, the player will show pictures or photos one by one from current picture. It will stop and return back when the last one has been shown, Press " STOP" button or tap touch screen button to stop the slide show mode.
Media Player DVD Disc Operation 1 7 4 12 13 14 15 16 17 18 9 RE L MODE NAVI NAVI VOICE 4 RD 1 M LOUD 2 5 SU RP BW 6 3 OSD SET UP T AS PS BAND 4x75WATT TA MCD 795 GPS MODE MUTE 2 3 6 8 5 7 8 1 2 7 10 11 Once a DVD disc is inserted into the unit, the unit will automatically start the playback from the beginning of the disc and then the DVD MENU or ROOT or TITLE in the DVD disc will appear on the TFT monitor and “ROOT” will be displayed on the TFT of the unit.
Media Player 2 Stop Function Press STOP or touch screen button to stop playback and show the logo screen. The player will memorize the last position where playback is stopped. Press PLAY or touch screen to resume playback from the positon where playback is stopped ( DVD, VCD 1.1, VCD 2.0 and audio CD). Pressing STOP twice or touch screen to resume playback from the beginning of the disc. 3 Repeat Function Short press REPEAT button less than 3 seconds to change from: repeat off -> repeat chapter.
Media Player 7 Next Function Press NEXT button or tap touch screen button when playing a disc, a chapter (DVD), a track (VCD / SVCD / CD), a song (MP3 / WMA), a picture (JPEG) , or a video file (AVI / MPEG4 / MPG/ DAT) is skipped forward accordingly.
Media Player Subtitle (On Remote Control) Pressing the SUBTITLE button on remote control, End user may select one of the subtitles language to show it on the screen or to turn off the SUBTITLE. This function is invalid for VCD / SVCD / CD, MP3 / WMA and JPEG. 9 DVD OSD ( D) Short Press AS / PS button, once to display the amount of time played and time remaining on the disc.
Media Player Language Setting Press the or touch screen buttons, move to the Language button. The list of available language will appear: Use the Use the buttons to select the setting. buttons to change among the available language. Press Ok or touch screen to cycle through each possible option or display a list of the available options. OSD language The OSD language setting provide the end user the selection of preferred language for the OSD menu and messages.
Media Player Subtitle The Subtitle setting allows the end user to select a preferred language and to change the subtitle language setup. Audio The Audio setting allows the user to select a preferred language and to change the Audio language setup . Disc The Disc setting allows the user to select a preferred language and to change the Disc menu language setup .
Media Player Display Setting Press on the remote control or touch screen buttons, to move to the Display button. The list of Display options will appear as follow: Use the Use the buttons to select the setting. buttons to change among the avaitable settings. Press Ok or touch screen to cycle through each possible option or display a list of the available options. TV Dispaly The Display setting allows the user to select the TV display.
Media Player TV Type The Display setting allows the user to select the TV type. The following options are available: Angle Mark The Display setting allows the user to select the Angle mark on/off mode.
Media Player Screen Saver End user can use this function to turn on or off the screen saver. Audio Setting Press on the remote control or touch screen buttons, move to the Audio button. The list of Audio optional will appear as follow: Use the Use the buttons to select the setting. buttons to change among the avaitable settings. Press Ok or touch screen to cycle through each possible option or display a list of the available options.
Media Player Downmix The Audio setting allows the user to select the Downmix and set downmix setup stereo analog output of this Player. Dual Mono The Audio setting allows the user to select the Dual mono and set dual mono(1+1) setup stereo output of this Player. Dynamic The Audio setting allows the user to select the Dynamic and set the dynamic sound output high volume outputs are softened.
Media Player Parental Setting Press the or touch screen buttons, move to the Parental button. The list of Parental optional will appear as follow: Use the Use the buttons to select the setting. buttons to change among the avaitable settings. Press Ok or touch screen to cycle through each possible option or display a list of the available options. Change Password This feature is used for Parental Control. Enter your four digit password when a hint is displayed on the screen.
Media Player Once entered the wrong password, the "Wrong Password" message will appear. To re-enter the correct password, end user need to move to "Enter Password " again, and try again. Once entered the correct password, press "OK" or touch screen and the " correct password" message will appear.
Media Player When the entered password is not matching, the " Passwords do no match" message will appear. End user should try to re-enter the password again and press the “ OK" or touch screen to confirm. Parental Level This function is to enter the Parental level control setup.
Media Player Press the " OK" or touch screen to enter the password. If the password is not correct, the " Wrong Password" message will appear. End user should try to re-enter the correct password again and press the " OK" or touch screen to confirm.
Media Player Default Setting the " Default “ function will reset all options and your personal settings to the factory defaults and all your personal settings will be erased. Use the buttons to select the setting. Press the " OK" or touch screen to confirm the selection.
AV-In Mode Caution: In order to avoid any accident, the driver must not watch video while driving. This unit is designed to not allow watching moving video while driving. Park your car in a safe place and engage the " parking brake" before watching moving video.
System Setting Operation To adjust the system Settings of this unit, tap on the main menu Setting screen button to enter into the setting menu, the below menu will appear: Settings Sound Setting Tap button on setting menu screen to access into the sound setting menu, the below menu will appear for selection.
System Setting Operation Tap level . button on the sound setting menu screen to select the Tap button to enter in the next page, the below menu will appear for selection. Note: Tap button to be return to the previous page. Setting Control Button Beep Tone Sub-Woofer Output Tap bar on the sound setting menu screen to turn on or off of these functions. On Tip: Tap Off button to exit the sound setting menu.
System Setting Operation Display Setting Tap button on the setting menu screen to access into the Display setting menu, the below menu will appear: Setting Control Screen Brightness Tap level .
System Setting Operation Tap bar to change time format to 24 hours. Calibration Tap bar on the Display Setting menu screen to start the Calibration setting. When the target moves to another position, tap and hold at the center of the new target. Repeat each time to complete the calibration process. Once completed, tap anywhere on screen to go back to menu screen. Note: This Calibration is for the display touch screen.
System Setting Operation Tuner Setting (Radio) Tap button on setting menu screen to access into the Tuner (Radio) setting menu, the below menu will appear: Setting Control Change Tuner seeking in Local or Distant mode.
System Setting Operation GPS Map Setting This setting is for end user to select for run the digital Map which is stored into SD memory card or in the built-in internal memory. Tap button on setting menu screen to access into the GPS Map setting, the below menu will appear: Setting Control Select to run Digital Map on internal memory Select to run Digital Map on SD memory card Important: To activates run the Digital Map on the SD Card. End user must switch off the GPS Navigation.
System Setting Operation Note: End user can purchase the authorized digital map and store it into SD Memory Card. Note: This unit ONLY CAN ACCEPT / RUN those digital map purchased from authorized dealers / agents. Any non-authorized digital map CANNOT BE USED on this unit. Note: This unit only can run the SD Card contained with digital map which is inserted into the panel's SD card slot. Please refer to the page "Overview of the unit" for more details of the SD card slot for Digital Map use.
System Setting Operation System Information Tap button on the settings menu screen to view the detail system information including serial number of this unit. The system information screen as follow. These information may different from unit to unit. System Information OS Version v06. 01. 20 Processor SAMSUNG ARM 920T-S3C2443 400MHz MemoryTotal 46752 KB RAM free 29988 KB Storage free 980 KB SW Version v01. 03. 00 08/07/08 RadioVersion v01. 03.
System Setting Operation Upgrade Setting Tap button on the settings menu screen to access into the upgrade menu, the below menu will appear: Note: Insert SD card with the upgrade files stored before proceeding with the upgrade and then tap on desired upgrade feature button in Upgrade mode.
System Setting Operation Setting APP MAP APP MAP Control This Upgrade should only be performed by approved sevice center or techinal support from authorized dealer. End user should never try to APP MAP the unit by themselves. This Upgrade should only be performed by approved sevice center or techinal support from authorized dealer. End user should never try to APP the unit by themselves.
System Setting Operation System Upgrade Setting Tap button on the upgrade settings screen to access into the System upgrade menu, the below menu will appear: Note: System Upgrade should only be performed by approved sevice center or techinal support from authorized dealer. End user should never try to System Upgrade the unit by themselves.
Memory Card Operation 1. Press the MODE button repeatedly on panel or remote control to switch between Tuner -> Disc -> USB - > SD Card - > AV IN Mode. Media Player 2. Aceess to MAIN MENU and tap MEDIA PLAYER. Tap the following buttons to start the playback of the desired media sources: Button to play the files in SD card Note: Please read below before you start the operation of Memory Card.
USB Operation 1. Press the MODE button repeatedly on panel or remote control to switch between Tuner -> Disc -> USB - > SD Card - > AV IN Mode. Media Player 2. Aceess to MAIN MENU and tap MEDIA PLAYER.
Navigation Operation What is GPS Navigation The term "navigation" is generally understood to mean the location of a vehicle, the determination of the direction and distance from the desired destination and the required route. As navigation aids, stars, prominent landmarks, compass and satellites are used. This unit, location is determined with the GPS receiver (GPS =Global Positioning System).
Navigation Operation To receive GPS signals successfully You have a clear sight of sky The GPS antenna is not covered The weather is good enough. GPS signal is weaker in bad weather conditions The time needed for establishing a GPS connection ranges from seconds to minutes. You are outdoor. When the positioning by GPS is impossible If signals cannot be received from more than two GPS satellites, GPS positioning does not take place.
Navigation Operation Conditions Likely to Cause Noticeable Positioning Errors For various reasons such as the state of the road you are travelling on and the state of reception of the GPS signal, the actual position of your vehicle may differ from the position displayed on the map screen. If you make a slight turn. If there is a parallel road. If you take a recently opened road that is not on the map.
Navigation Operation If you drive in zig-zags. If the road has connected hairpin bends. If there is a loop or similar road configuration. If you take a ferry. If you are driving on a long, straight road or a gently curving road. If you are on a steep mountain road with many height changes.
Navigation Operation If you enter or exit a multistorey car park or similar using a spiral ramp. If your vehicle is turned on a turntable or simi-lar structure. If your vehicle’s wheels spin, such as on a rough track or in snow. If you put on chains or change your tyres for ones with a different size. If trees or other obstacles block the GPS sig-nals for a considerable period. If you drive very slowly, or in a start-and-stop manner, as in a traffic jam.
Navigation Operation If you join the road after driving around a large car park. When you go round a roundabout. When starting driving immediately after start-ing the engine. If you turn your navigation system on while driving. Some types of vehicles may not output a speed signal while driving at just a few kilometres per hour. In such a case, the current location of your vehicle may not be displayed correctly while in a traffic jam or in a car park.
Navigation Operation Digital Map This unit is pre-loaded with the below digital map marked with Yes inside the INTERNAL BUILT-IN FLASH MEMORY: Maps Pre-Loaded Eastern Europe Albania Belarus BosniaHrz Bulgaria Croatia.
Navigation Operation Start Navigation Mode Caution: For safety reasons, you can not use some of navigation functions while your vehicle is in motion.To enable these funcions, you must stop in a safe place and apply the handbrake. Park your vehicle in a safe place and apply the handbrake. How to get into the GPS Navigation system Please read the below instruction carefully before operating the unit. 1) First power on the unit by pressing the " POWER / MUTE" button.
Navigation Operation When in AV IN Mode, end user can tab on the touch screen, to bring up the menu, and then press on the NAVI button ON THE TOUCH SCREEN to get into the GPS NAVIGATION MODE. NAVI NAVI VOICE End user can press the MODE button repeatedly, until the " MAIN MENU" appear on the screen, then press the mode GPS button to get into the GPS NAVIGATION MODE.
Navigation Operation Attention! If you are using the software product during driving or transportation, we strongly advise you to direct all your attention to driving or transportation, and to Especially do not try to operate, enter data into or obtain data from the software product while driving, because such presents a life hazard, and the lack of proper attention may cause death, injury or matertal damge.
Navigation Operation Highlight Features The following are the highlight navigation features : Navigation Voice Guidance under Tuner or Media Player playback During the navigation mode, music of Tuner or Media player can still be heard. This unit will automacitally MUTE the music of tuner or Media player when there is announcement from the navigation voice guidance. This function can be activate or deactivate by: Long pressing the NAVI VOICE button on panel. Tapping on the touch screen buttons: 1.
Specification General Operating Voltage Grounding System Fuse: Operating Temperature: Unit Mounting Angle DC 11 -14.4V Negative Ground 15-Amp Mini ATM Type 0°C to 50°C < 30° TFT Screen Screen Size: 3.5"(Measured Diagonally) Screen Type: TFT Liquid Crystal Display active matrix Resolution: 960 (W) x 324 (H) Radio FM Frequency Range Usable Sensitivity Stereo Separation S/N Ratio 87.5-108.
Specification Media Player DVD / CD Compatible Disc/Format Signal to Noise Ratio Dynamic Range Frequency Response Channel Separation See “Disc Note” for more details description > 90 dB > 90 dB 20Hz to 20Khz +/-3dB 2 Channel (Stereo) >60dB @1khz Video Color System Video Output Video Input NTSC / PAL Composite 1.0 Vp-p (+/- 0.2) 75 - ohm Composite 1.0 Vp-p (+/- 0.
Trouble Shooting Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power The car ignition is not on. If the power supply is properly connected to the car accessory terminal, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Disc cannot be loaded or ejected Presence of CD disc inside the player.