Page CONTENTS 01 Contents 02 Installation 04 Using the detachable front panel 05 Wiring Diagram 06 Operations 06 Location and Function of Keys 07 General Operations 09 Radio Operations 09 RDS (Radio Data System) Operations 11 CD/MP3 /WMA Disc Operations 12 Mixed-CD Operations 12 USB Device Operations 13 SD/MMC Card Operations 13 AUX in Operations 13 Bluetooth hands-free Function 15 Specifications 16 Disc Notes 17 Trouble Shooting
Installation Notes: Take Out Screw Before Installation Before install the unit, please remove the two screws. - Choose the mounting location where the unit will not interfere with the normal driving function of the driver. - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. - Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. 10. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel (see the steps of 'to install the front panel').
2. DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow this mounting instruction. Use the screw holes marked T (Toyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Using The Detachable Front Panel REMOVING THE FRONT PANEL 1 . Press the release front panel . button on the 2 . Pull off the front panel . Fasten the unit to the factory radio mounting brackets.
Wiring Diagram RCA connector to front left output (White) RCA connector to rear left output (White) Antenna Socket Bluetooth Antenna L R FUSE FUSE 15A ISO CONNECTOR RCA connector to rear right output (Red) RCA connector to front right output (Red) TO MEMORY B+ GROUND BACC B+ FRONT 4 ohm YELLOW BLACK BLUE WHITE GREY WHITE / BLACK GREY / BLACK LEFT SPEAKER ISO connector: Part A: A1: No Connect A2: No Connect A3: No Connect A4: Battery B+ (Yellow) A5: Antenna (Blue) A6: No Connect A7: Access
Operations Location and Function of Keys Front panel: 19 1 2 5 22 26 7 27 CAR CD/MP3 PLAYER WITH ESP AF 8 TA 7 8 20 24 9 Push SEL DISP 9 PTY AUX IN MIC BAND ENT 21 AMS MENU 4 11 3 MOD 0 1 6 10 12 SCN RPT SHF - 10 + 10 2 3 4 5 6 17 18 13 14 15 16 23 The front facet after removing the front panel: 26 25 28 29 Descriptions of Function Controls (1) Power on/off Button ( ), Mute Button (2) Volume Control, Audio/Menu Selector (SEL) (3) Built-in Microphone for blu
General Operations Reset the unit When operating the unit for the first time, after replacing the car battery or changing the connections, you must reset the unit. 1.Turn off the unit power. 2.Press the REL ( ) button and remove the front panel, then press the RESET button with a ballpoint pen or similar object to restart the unit. Power on/off In power off mode, switch on the unit by pressing any button except the REL ( ) button.
LOCAL RECEPTION ON/OFF: In urban areas, most stations are strong enough and “LOCAL ON” mode should be selected. Switch to LOCAL OFF mode to search for stations with weaker signals. Rotate the volume control to switch local reception ON or OFF mode. STEREO/MONO : FM station is received in stereo mode. However, if the signal is weak or reception is not as good as you would like, switching to MONO mode usually improves the overall sound quality. R otate the volume control to choose stereo or mono audio effect.
Radio Operations To select a radio band In tuner mode, Press the BAND button repeatedly to select a radio broadcasting band you would like to hear. The FM band is toggled cyclically through the tuning bands: ->FM 1-> FM 2 -> FM 3 -> . Auto/ Manual tuning - Automatic search mode: Briefly press the : or 9 button, the auto search will start. It will search upward or downward for the strong signal radio station within the current band. In auto tuning, press the : or 9 button to stop tuning.
Using PTY select function Pressing and holding the PTY button for more than 2 seconds to enter the PTY menu. The default type is NEWS.
CD/MP3/WMA DISC OPERATIONS Switching to CD/MP3 mode 1. If there is no CD/MP3 disc inserted in the player: Gently insert a CD/MP3 disc with the printed side facing up into the disc slot until you feel some resistance. The disc is draw into the driver automatically. The CD/MP3 playback begins. 2. If a CD/MP3 disc is already inserted in the player, press MODE button to switch to the CD/MP3 mode. Loading/Removing a Disc 1.
Press the SEL button to confirm the character entered and advance to the next character. c) When mached files was found, rotate the volume control or press the : / 9 button to change and select your desired file among these files with same search keyword, then press the BAND (ENTER) button to start play the searched file. If the file was not found, “NO MATCH” message will be visible on the display.
SD/MMC Card Operations This unit equipped with you a memory card slot. Using the SD/MMC card: When you insert a SD/MMC card into the memory card slot, the player will reading the SD/MMC card automatically. If insert a disc into the disc slot while read the SD/MMC card, the unit will playing the disc. If you want to play the file in the SD/MMC card, press the MODE button to switch to SD/MMC mode. SD/MMC memory card playing operation is the same with the MP3 operation described.
3. DIAL CALL 3.1 Dial with the mobile phone directly. 3.2 Dial with the 0 ~ 9 numeric button. 3.2.1 In connect status, press the MENU button to activate the bluetooth mode, 3.2.2 Press the “ 0 ~ 9 ” button to input telephone number. Simultaneously, the input number will be appeared on the LCD display. If a number is wrongly input, press and hold the 9 button to delete the incorrect number. 3.2.3 press the “ ” button to execute dialing. 3.3 Dial the last number 3.3.
8.2 When playing A2DP, user can control playback by using the relevant function control. Eg.: - Play/pause by pressing button. - Previous/next track by pressing : / 9 button. Note: While playing A2DP, if you execute outgoing call or incoming call, the A2DP function will be canclled automatically , and you need to re-activate after phone call. WARNING: 1. To get the best conversation quality, it is recommended that the distance between the mobile phone and the unit is within 3m.
Disc Notes A. Notes on discs: 1. Attempting to use non-standard shape discs (e.g. square, start, and heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction. Dirty, dusty, scratched and warped discs will cause a malfunction. B. Notes on CD-Rs (recordable CDs)/CDRWs (rewritable CDs): 1. Be sure to use discs with following marks only for the unit to play: 2.
Trouble Shooting The following chart will help in solving most problems that may occur. If you still have questions after going through the checklist, please consult your local customer service representative. Before going through this check list, refer the wiring and operating procedures. Symptom Cause The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown.
