RMD 575BT / RMN 575BT MANUAL ENGLISH
INSTALLATION Tools for Installation Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and supplies may also be needed for the installation: Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires The above are not supplied.
INSTALLATION WARNING! Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery. NOTE: Remove the two transport screws from the top of the unit before installing. NOTE: Make sure there is enough space for the installation of this single-din in-dash.
WIRING DIAGRAM Amp power (+12V output-blue/white) MIC GPS Antenna Parking (green) Reverse(purple-white) Steering wheel control (3.5mm jack) BACK CAM VIDEO OUT SUB OUT AUX VIDEO AUX IN (L) AUX IN (R) RCA OUT (F L) RCA OUT (F R) RCA OUT (R L) RCA OUT (R R) Radio Antenna Connector A 1. Rear right speaker(+)/Purple 2. Rear right speaker(-)/Purple-Black 3. Front right speaker(+)/Grey 4. Front right speaker(-)/Grey-Black 5. Front left speaker(+)/White 6. Front left speaker(-)/White-Black 7.
WIRING DIAGRAM General Wiring Notes: Make sure You have a good chassis ground. Good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the .vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good ground connection. Black Ground Connect to vehicle body/chassis. Make sure you have a good chassis ground.
Specifications GENERAL Operating Power.......................................................................................................................................12 Volts DC, Negative Ground Output Wiring...............................................................................................................................Designed for using four speakers only RCA line out........................................................................................................................
BASIC Operation 1. Tuning the unit On / Off Press the Power Button to turn the unit on. The opening screen of the unit will be showing on the TFT monitor. Press and hold the POWER button again to turn the unit off. 2. Turning the TFT On / Off During any play mode, press the Power Button once to turn the TFT screen off for screen saving and avoid distraction while driving. The sound will continue to play. Press the Power Button again to turn the TFT screen back on.
Radio Operation 1. Choose Radio Band Touch the AM button on screen to choose among the five radio bands - three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations. 2. Radio Seek Function In Radio Mode, touch and hold frequency manually. or 3. Save Your Preset Stations Press the button and then press the Button to adjust the radio frequency automatically.
Radio Operation (Con’d) 6. Mono/Stereo Reception Control In FM radio mode, touch the ST button to select stereo or mono reception. 7. Local/Distance Reception Control In radio mode, touch the LOC button to select local or distance reception. 8. RDS Control AF, TA, PTY are the RDS functions. They are applicable to certain countries only. For countries when RDS is not available. The touch sensitivity of the button will be disabled. 9.
Bluetooth Operation PAIRING At BT mode, search bluetooth device by the phone and “RMN575BT Caliber” will appear in your phone. Input “0000” as password to establish connection. DIAL PAD Touch the dial pad to dial the number you would like to call. Touch the CALL (green) button to send the number. CONTACT Press the CONTACT button to enter phone book function. Press the button to download the phone list. Press the to search the contact person. Press the button to delete the phone list.
Bluetooth Operation (Con’d) View Received Calls Touch the RECEIVED CALLS button, the received calls will be displayed. View Missed Calls Touch the MISSED CALLS button, the missed calls will be displayed. View Dialed Calls Touch the DIALED CALLS button, the dialed calls will be displayed. Playing Music on your cellphone After activating music player in the cellphone and it will play automatically, touch to select uo or down one song in your song list. 12 to play or pause the music.
USB Operation Plug the USB device into the USB port. The unit will play the contents automatically. 1. Advance / Go Back Advance to the next track or go back to the previous track by pressing the forward or rewind buttons on the front panel or touch screen. 2. Play/Pause Press the play/pause button to pause the playback or resume. 3. Fast Forward/Fast Rewind Press and drag the proceeding bar during media playback. The unit will fast forward/rewind the song/video until you release. 4.
USB Operation 7. Repeat Function Press the Repeat button to toggle between repeat chapter, repeat single, repeat all and repeat off. 8. Subtitle Selection Press the Sub-T button to choose the sub-title you want. The sub-title languages available differ from Disc to Disc. You can also use the setup menu to confirm. Refer to the packing of the Disc for details. 9.
Settings General Setting The general setting menu includes any key power, video warning, GPS monitor, BT phone book auto deleted, strong sort, brightness, Screen reguate, factory set, calibration, serial and version, GPS monitoring, language setting, reset factory.
Settings EQ Setting You may set EQ, touch sound, back car vol, user def vol, GPS mix, report point remove mute, BT default vol button, BT call vol, def vol under this setting. Time Setting You can select Date, Time, Time mode and Time zone by tapping directly on the options . Tap after the setting to take effect.
Settings GPS Setting Enter the GPS setting to define the link of the execution file of your GPS program. Consult the installer if you are not familiar with the setting. Tap OK after the full path is inserted. Now you can enter the Navigation mode in the OSD. Make sure you have inserted the GPS map card properly (the lower micro SD card slot of the front panel) before the settings. Wall Paper Selection Tap the Wall button on the right bottom corner of the OSD.
Steering Wheel Control (Optional) Refer to the wiring diagram for connection. The brown wire (SWC 1) must be connected, then the white or grey (SWC 2A and 2B) will be connected depending on the total number of the wire from the steering wheel remote control of your vehicle. TAB STEERING WHEEL LOGO in the OSD. Press before the set up. Select from the 10 functions according to the number of available keys on the steering wheel of your vehicle.
Other Operations 1. GPS Navigation If GPS navigation is available with the system, Tap the GPS logo on the OSD to enter GPS navigation. Follow the on screen instruction to input destination and start navigation. The operation varies from software to software. 2. AV Input The AV Input Jack is a set of composite input on the rear of the unit. Press the Mode button to choose AUX. Connect any portable audio/video device such as a DVD player. Use the volume control to adjust volume. 3.
INFRA RED REMOTE CONTROL 1 2 3 MOD 5 6 7 8 9 10 11 12 13 14 15 16 17 BAND 4 MUTE TITLE SUB-T SETUP ENTER ANGLE SLOW AMS RPT ST PROG LOC RDM SEEK PBC OSD 1 2 3 4 5 6 7 8 9 0 10 VOL SELECT VOL ZOOM SEEK AUDIO GO TO 18 19 20 21 22 23 24 25 26 27 28 29 30 1.Power on/off 2. Mode Select Key 3.Play / Pause Function 4.Mute Sound Function 5.Band Select 6/7/10/21.Cursor Button in Menu Mode 8.Confirm The Track/Chapter Selected or Select Item In SETUP Menu 9. Stop Playback 11.
SIMPLE TROUBLESHOOTING GUIDE PROBLEM CAUSE / SOLUTION No Power Check whether the fuse is blown, replace with fuse of proper value if necessary. Unit stops responding or shows error in display Press the RESET button. Unable to receive radio stations Check whether the antenna is inserted or the antenna is properly connected; if not, insert the antenna or connect it properly. Poor effect on receiving a station -Antenna may not be of the proper length. Make sure the antenna is fully extended.
W W W. C A L IBE R. N L CALIBER HEAD OFFICE • The Netherlands • Fax: +31 (0)416 69 90 01 • E-mail: info@caliber.
