INSTALLATION PRECAUTIONS • Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. • Use only the supplied mounting hardware for a safe and secure installation. • Be sure to remove the front panel before installing the unit.
TO SUPPORT THE UNIT 3 Dashboard 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
DRIVING WITH VIDEO DISPLAY By following the installation below, video will always be shown on LCD screen no matter the car is in motion or not. Steps: Connect the GRAY wire to the WHITE wire. INSTALLING REAR CAMERA FOR PARKING/REVERSE MOTION You can install an separate camera at the car rear end so when doing parking or reverse motion, the unit will automatically switch the video to the rear camera to guide the driver.
RMD 610BT BlueTooth 4x 75WATT Locations of Parts (Main unit) 1 2 7 9 12 11 10 4 13 14 1 2 6 7 22 9 RMD 610BT 12 AUX IN RMD 610BT 16 17 15 3 (1-3) 1. 2. 3. 4.
Locations of Parts (Remote Control) 8 1. POWER ON/OFF 2. MODE 3. PLAY/PAUSE 4. TITLE 5. SELECT 6. SEEK+/SEEK- / TRACK/SEARCH 7. VOL +/VOL- 8. GOTO 9. AUDIO 10. ENTER 11. NAVIGATION 12. AUTO SEEK / PRESET SCAN / REPEAT 13. RANDOM / BAND / LOUDNESS 14. DUAL 15. PAL / NTSC SYSTEM 16. SUBTITLE 17. SETUP 18. EQUALIZER 19. SLOW MOTION 20. ZOOM / A-B REPEAT 21. STOP 22. CLOCK / ON SCREEN DISPLAY 23. MUTE 24. MAIN MENU 25. STEP (FRAME BY FRAME PLAYBACK) 26. Program Type 27. Alternative Frequencies 28.
OPERATIONS Turning the unit ON/OFF ( ) Press “ ” button to turn on unit. To turn off, press the button again. MAIN MENU This is the root of the screen hierarchy and you can simply access all features by tapping on the touch screen buttons. Selecting a source (MODE) Press MODE repeatedly to switch between TUNER, AUX IN, USB, SD/MMC or BLUETOOTH (if Bluetooth is connected) mode. Adjusting Volume • Head Unit: Rotate VOL knob right or left to increase or decrease volume.
Auto Seek/Preset scan (A/PS) Preset Scan (PS) - By pressing shortly, the radio plays each preset station for 5 seconds. Auto Seek (AS) - By pressing longer than 1 sec, auto seek is activated. The 6 strongest stations are preset and stored in the corresponding preset number. When Auto Seek operation is finished, the radio executes the preset scan.
3. Let the movie play on until you have reached the end of the section you wish to watch on continuous loop. Once you have reached this point, press and hold A-B button again. “Rep-A-B” will appear on your screen. Playback will now start from Point A –B. 4. To stop A-B repeat playback, press and hold A-B button once more until “A-B CANCEL” disappears and normal playback resumes. Displaying information (OSD) During playback, you can see all information and current play settings.
Zooming in During Playback You can zoom in into the picture during playback. 1. Press ZOOM on the remote control during playback. 2. Every time you press this button, the unit will zoom 2 - 3 - 4 - 1/2 - 1/3 - 1/4 times and OFF. Frame-by-frame playback This lets you move ahead one frame at a time during playback. 1 Each time you press Step button on remote control, you move ahead one frame. To return to normal playback, press . PAL / NTSC (P/N) Press and hold P/N button to switch between PAL, NTSC system.
SETTING THE MPEG4 PLAYER You can flexibly customize the unit to suit your preference. You can set the language and other video and audio settings so when playback starts it will always use your preferred settings. Important: 1. Play any video file before you can access the setup. 2. Press Setup on the remote control. 3. Use ( / ) to return / enter category.
TECHNICAL SPECIFICATIONS MP3/WMA PLAYER SECTION Signal to Noise Ratio Channel Separation Frequency Response > 60 dB > 50 dB (1kHz) 20 Hz - 20 kHz TUNER (FM) Frequency Range Channel Step Sensitivity Stereo Separation Signal to Noise Ratio 87.5-108 MHz 50 kHz 2.8 µV 30 dB 50 dB LINE-OUT Output Impedance 1300 mV (max.) 10k Ohm AUX-IN Frequency Response Sensitivity Impedance 20 Hz - 20 kHz 775 mV 20k Ohm GENERAL Power Supply Speaker Impedance Output power Fuse 12V DC (10.8-15.