Instruction Manual

ManualsBrandsCALIFORNIA AIR TOOLS ManualsPressure PotCALIFORNIA AIR TOOLS 1810C 10 Gallon Casting Pressure Pot

California Air Tools

10 Gallon Casting Pressure Pot

Model No. 1810C

Technical Data

Item ……………………………………………………………………………………….…………1810C

Maximum pressure in the tank……………………………………………………………...….80 PSI

Working pressure in the tank…………………………………………………………………...60 PSI

Tank capacity………………………………………………………………………………40 I (10.0 gal)

Air Inlet………………………………………………………………………………….….1/4” Industrial

Interior………………………………………………………………. Diameter 17 3/4" & Depth 9 5/8"

Summary of content (8 pages)

PAGE 1
California Air Tools 10 Gallon Casting Pressure Pot Model No. 1810C Technical Data Item ……………………………………………………………………………………….…………1810C Maximum pressure in the tank……………………………………………………………...….80 PSI Working pressure in the tank…………………………………………………………………...60 PSI Tank capacity………………………………………………………………………………40 I (10.0 gal) Air Inlet………………………………………………………………………………….….1/4” Industrial Interior……………………………………………………………….
PAGE 2
Safety Guidelines- Definitions NOTE! Information that you should pay special attention to. DANGER! URGENT SAFTEY INFORMATION A HAZARD THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE CAUTION! Information for preventing damage to equipment WARNING! IMPORTANT SAFETY INFORMATION A HAZARD THAT MIGHT CAUSE SERIOUS INJURY OR LOSS OF LIFE Important Safety Instructions Save These Instructions IMPROPER OPERATION OR MAINTENCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAG.
PAGE 3
Assembly Read the instructions carefully Read instructions carefully before using this product. This equipment can be used to supply up to a maximum of 80 (PSI). Operating PSI is 60 PSI. This equipment has an air regulator, pressure gauge, safety valve and outlet. The tank has been coated to last. . Air Compressor Use an air compressor that can produce at less 90 PSI. 1. WARNING! Ensure the air supply is clean and does not exceed 80psi while operating the tool.
PAGE 4
WARNING! Risk of tank explosion. 1. Modifications to the tank’s design or construction could weaken it. Assemble tank components in accordance with the service instructions. Do not drill into tank, or weld attachments, or alter its design in any manner. 2. Substitution of unauthorized non-standard components could weaken tank or cause component failure. Use only those components furnished with the tank. Assembled in accordance with instructions in the service literature. 3.
PAGE 5
Maintenance and Storage 1. Close the air flow to the equipment. 2. Release all air pressure in the tank by pulling the safety valve ring until the pressure subsides. 3. Rotate the tank regulator handle “T” counterclockwise until you do not feel any tension in the spring. 4. Loosen the metal screws, remove the wing nuts, and open the lid to one side. 5. Loosen the metal rings on the gun nozzle about three turns. 6. Open the air supply. 7.
PAGE 6
Trouble Shooting WARNING! If any of the following symptoms appears during your operating, stop using the tool immediately, or serious personal injury could result. Only a qualified persons or an authorized service center can perform repairs or replacement of tool. Disconnect tool from air supply before attempting repair or adjustment. When replacing O-rings or Cylinder, lubricate with air tool oil before assembly.
PAGE 7
EXPLOSIVE DRAWING OF CAT-1810C NO. DESCRIPTION NO.
PAGE 8
Limited Warranty This Warranty is Limited to CALIFORNIA AIR TOOLS and SPRAYIT Products. Limited Warranty: 1 Year CALIFORNIA AIR TOOLS, Inc. will repair or replace, free of charge, to the original retail customer whom purchased a CALIFORNIA AIR TOOLS or SPRAYIT product from an authorized dealer, distributor or distributor’s dealer. This warranty does not transfer to subsequent owners. CALIFORNIA AIR TOOLS, Inc.