User's Manual

This document is subject to change without notice.
Document No: 0020-00-07-00-000 (Issue A)
11
PRELIMINARY DATASHEET
ZB3212F6R4SP2
AGENCY CERTIFICATIONS
NOTE: Certifications are in process and pending final approval
FCC Compliance Statement Part 15.19, Section 7.15 of RSS-GEN
This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS Standards. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Warning (Part 15.21)
Changes or modifications not expressly approved by CEL could void the user's authority to operate the equipment.
20cm Separation Distance
To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20cm from all persons and must not be operated in conjunction with
any other antenna or transmitter.
OEM Responsibility to the FCC and IC Rules and Regulations
The Cortet Mini Module has been certified per FCC Part 15 Rules and to Industry Canada license exempt RSS Standards for
integration into products without further testing or certification. To fulfill the FCC and IC certification requirements, the OEM of the
Cortet Module must ensure that the information provided on the Cortet label is placed on the outside of the final product. The
Cortet Mini Module is labeled with its own FCC ID number and IC ID number. If the FCC ID and the IC ID are not visible when
the module is installed inside another device, then the outside of the device into which the module is installed must also display a
label referring to the enclosed module. The exterior label can use wording such as the following
“Contains Transmitter Module FCC ID: W7Z-WB4343S”
“Contains Transmitter Module IC: 8254A-WB4343S"
The OEM of the Cortet Mini Module may only use the approved antennas (PCB Trace Antenna) that have been certified with this
module. The OEM of the Cortet Mini Module must test their final product configuration to comply with Unintentional Radiator
Limits before declaring FCC Compliance per Part 15 of the FCC Rules.
IC Certification — Industry Canada Statement
The term "IC" before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
Certification IC — Déclaration d'Industrie Canada
Le terme "IC" devant le numéro de certification/d'enregistrement signifie seulement que les spécifications techniques Industrie
Canada ont été respectées.
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in
excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's website:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php
L'article 14 du CNR-210
Le programme d'installation de cet équipement radio doit s'assurer que l'antenne est située ou orientée de telle sorte qu'il ne
pas émettre de champ RF au-delà des limites de Santé Canada pour la population générale. Consulter le Code de sécurité 6,
disponible sur le site Web de Santé Canada: http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php