Installation Sheet

33""
78""
1-1/2" min
1/2"
3-1/2"
8"
Lower Outlet:
1/2" NPT to tub
1-1/4" Opening
"A" Dimension
** 2-11/16"
6"
4-3/4"
Stem
Broach
Finished Wall
All
Thread
Front View
INSTALLATION
INSTRUCTIONS
3-WAY VALVE
Cold Inlet:
1/2" NPT Male
or 1/2" Copper Sweat
IMPORTANT CLEANING NOTICE Please refer to Finish Care Instructions for complete cleaning information. Wipe frequently with a soft, damp
cloth.
Never use acids, harsh abrasives or detergents.
NOTE : When fitting handle it
may be necessary to shorten
broach stem and/or all thread
to eliminate gap between
handle & escutcheon.
Hot Inlet:
1/2" NPT Male
or 1/2" Copper Sweat
3-VR
Tel: [phone]
Fax: [phone]
Toll Free: 800-822-8855
www.calfaucets.com
California Faucets reserves the right to make modification and specification changes at any time. Please visit www.calfaucets.com for most current technical data.
3-VR_ii_151118
Side View
"A"
DIMENSION
"A" Dimension is
from finished wall
to tip of stem broach
Handle
Series # "A"
33 2-3/8"
** NOTE : For Series #71, 72 & 73 valve rough
must be set back a minimum of 2-11/16” from
finished wall surface to center of inlets.
Upper Outlet:
1/2" NPT to shower
Showerhead
Tub Spout
3 Valve (handle) Rough
Floor Line
Tub Rim
NOTE: These are recommended
dimensions only. Always refer to local
plumbing codes prior to installation.
Tub Spout
Showerhead
NOTE : In some cases, it may be necessary to re-align cartridge
Stem
to achieve desired handle alignment. To align stem, slightly
loosen in a CCW direction the Cartridge Nut
. Place Hanlde on
Stem
and TIGHTEN in a CW direction until desired alignment
of handle is acheived. Retighten Cartrdge Nut
to factory torque
setting of 14 ft-lbs. (Cartridge Nut size is 13/16" hex)
WARNING : Cartridge Nut
MUST be propler torqued to
prevent possible failure and/or water damage.
Cartridge Nut
(13/16" hex)
Stem
Handle
34 2-3/8"
35 2-3/8"
36 2-3/8"
38 2-5/8"
42 2-5/8"
44 2-7/16"
45 2-1/8"
47 2-1/2"
48 2-5/16"
50 2-1/4"
51 2-1/2"
53 2-1/4"
55 2-5/8"
57 2"
59 2-5/8"
60 2-1/4"
62 1-7/16
63 3"
64 2-5/8"
65 2-1/8"
66 2-1/8"
67 2-1/4
68 2-3/8"
69 2-3/8"
**71 1"
"A"
DIMENSION
"A" Dimension is
from finished wall
to tip of stem broach
Handle
Series # "A"
33 2-3/8"
34 2-3/8"
35 2-3/8"
36 2-3/8"
38 2-5/8"
40 2-5/8"
42 2-5/8"
44 2-7/16"
46 2-1/2"
47 2-1/2"
48 2-5/16"
50 2-1/4"
51 2-1/2"
53 2-1/4"
55 2-5/8"
57 2"
59 2-5/8"
60 2-1/4"
62 1-7/16"
63 3"
64 2-5/8"
65 2-1/8"
66 2-1/8"
67 2-1/4
68 2-3/8"
69 2-3/8"
**71 1"
**72 1"
**73 1"
Tub Spout
**72 1"
**73 1"
**77R 1"
46 2-1/2"
Showerhead
33""
78""
1-1/2" min
1/2"
33""
78""
1-1/2" min
1/2"