Installation Sheet

ManualsBrandsCalifornia Faucets ManualsShop All California FaucetsCalifornia Faucets Monterey 1.2 GPM Widespread Bathroom Faucet - Includes 2-1/4" ZeroDrain

For spout with 4-way tee:

-Remove the Tee, Flange Nut and Stainless Steel Washer.

-Insert the spout through center hole of the sink or

countertop.

-Place Washer and Flange Nut onto Shank

from below. Align spout and tighten Flange Nut until Spout is

firmly in place.

-With O-Ring in place on end of Shank, slide Tee onto Shank.

-Place the Rubber Washer, Brass Washer and Nut

onto Nipple and tighten.

Stainless Washer

Flange Nut

Rubber Washer

Nut

Brass Washer

1/2"x3/8"x12"

Flex Line

Bottom

Nut

Brass

Supplied Nut

Min. 8"

INSTALLATION

INSTRUCTIONS

4-Way Tee Shown

Fig. 2

Fig. 1

Lock Nut

***NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***

For spout with 3-way tee:

-Remove the tee, lock nut and notched washer.

-Insert the spout through center hole of the sink or

countertop.

-Slip the notched washer over spout shank. Align

notch for pop-up rod to pass through, then thread

lock nut onto the spout shank. Align spout

and tighten nut firmly.

-Place white washer into top of tee and screw

assembly onto spout shank.

-Insert lift rod through top of spout

O-Ring

(If necessary apply grease)

Notched Washer

Lock Nut

Fig. 3

Nipple

Shank

Rubber Washer

Flow Restrictor

& Rubber Washer

(For use on model

#5302 only)

1 Install spout according to the type of tee it has:

Shank

WIDESPREAD FAUCETS

IMPORTANT

All

California Faucets

products are engineered to provide quality performance provided

they are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your

new Widespread Faucet, please follow the instructions below.

4-Way

Tee

3-Way

Tee

California Faucets reserves the right to make modification and specification changes at any time.

Please visit californiafaucets.com for most current technical data.

800-822-8855

5271 Argosy Ave.

Huntington Bch, CA 92649

californiafaucets.com

Pg 1

WS_ii_130501

NOTE: Due to sediment in the water it may

be necessary on occasion to remove the aerator

and clean the screen with a soft bristle toothbrush.

Please refer to Finish Care Instructions for complete

cleaning information. Wipe frequently with a soft, damp

cloth. Never use acids, harsh abrasives or detergents

IMPORTANT CLEANING NOTICE

Fiber

Washer

Stainless Washer

(1 1/8" Hole size for

Handle

Escutcheon

Decorative

Base Ring

Set Screw

Sink/

Countertop

drilling, recommended)

Hot

Cold

"A"

Handle

Series # "A"

DIMENSION

"A"

"A" Dimension is from sink/countertop

to tip of stem broach

32 2 5/16" 53 2 1/4"

33 2 5/16" 55 2 7/16"

34 2 5/16" 57 1 11/16"

35 2 5/16" 58 2 1/2"

36 2 5/16" 59 2 1/2"

38 2 1/2" 60 2 1/16"

40 2 7/16" 61 2 1/16"

42 2 7/16" 63 2 15/16"

45 2" 64 2 1/2"

46 2 5/16" 67 2 1/16"

47 2 5/16" 68 2 5/16"

50 2 1/8" 69 2 5/16"

51 2 1/2"

Handle

Series # "A"

Summary of content (2 pages)

PAGE 1
800-822-8855 5271 Argosy Ave. Huntington Bch, CA 92649 californiafaucets.com INSTALLATION INSTRUCTIONS WIDESPREAD FAUCETS IMPORTANT All California Faucets products are engineered to provide quality performance provided they are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your new Widespread Faucet, please follow the instructions below. ® California Faucets reserves the right to make modification and specification changes at any time.
PAGE 2
Install valve bodies: NOTE: Hot & cold valves are labeled: cold=blue & hot=red. -Remove top nut and turn bottom nut with fiber washer down the valve until it stops. -Insert valve through hole from below and install top nut (if applicable), and adjust to proper height, see Fig. 4A (also refer to "A" dimension table on page 1). -Tighten the bottom nut to secure the valve. -Install trim parts (base ring if applicable), escutcheon and handle and tighten handle set screws with Allen key provided.