Installation Sheet

ManualsBrandsCalifornia Faucets ManualsKitchen FaucetsCorsano Single Handle Single Hole Pull-Out Spray Bar / Prep Faucet

CF-KXX-110_ii_150901 Pg 1

CF-K51-110

& CF-K51-111

Kitchen/Prep Pull-Out Faucet

Installation Instructions

IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer.

Operating Specifications:

Recommended Supply Pressure: 20 to 70 psi

*†

* Operating pressures between hot and cold supplies should vary no more than 30 psi.

† If water pressure exceeds 70 psi, install a Pressure-Reducing Valve (RPV).

INSTALLING TO SINK/DECK

Important: The recommended sink/deck through-hole shall be Ø1-

3/8”. Maximum sink/deck thickness should no greater than 2-1/4”

 Place BASE (2) with O-RING (3) onto BODY (1)

 Slide INLET HOSES (4) and SPRAY-HOSE (5)

through sink/deck hole

Important: Based on sink/deck thickness the use of SPACER (6a)

needs to be determined. If thickness is LESS than ½” use SPACER

(6a), if GREATER than ½” use only MOUNT (6).

 From underside slide SPACER (6a), in necessary,

MOUNT (6) and NUT (7) onto SHANK (1a);

loosely tighten NUT (7)

Important: Position MOUNT (6) so that SPRAY-HOSE (5) does

NOT rub against MOUNT (6) when SPRAYHEAD (8) is pulled.

 From topside position BODY (1) with handle on

right side as shown and from underside securely

tighten NUT (7)

Position MOUNT (6)

to prevent rubbing of

SPRAYER HOSE (5)

CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED

BY A LICENSED PROFESSIONAL

Ø1-3/8”

Summary of content (4 pages)

PAGE 1
CF-K51-110 & CF-K51-111 Kitchen/Prep Pull-Out Faucet Installation Instructions CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED BY A LICENSED PROFESSIONAL IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer. Operating Specifications: Recommended Supply Pressure: 20 to 70 psi *† * † Operating pressures between hot and cold supplies should vary no more than 30 psi. If water pressure exceeds 70 psi, install a Pressure-Reducing Valve (RPV).
PAGE 2
WATER CONNECTIONS Important: The water supplies MUST be flush of all debris prior to running water through the faucets SPRAYHEAD (8); the following procedure will ensure debris removal.
PAGE 3
FINAL CONNECTIONS  Tighten CHECK ASSEMBLY (12) onto end of SHANK (1a)  Attach SPRAY-HOSE (5) onto end of CHECK ASSEMBLY (12) CHECK ASSEMBLY MAINTENANCE o Disconnect CHECK ASSEMBLY (12) from SPRAY-HOSE (5) and SHANK (1a) o Unscrew UPPER HOUSING (12a), remove both CHECK VALVES (12b) by gently pushing through hole in LOWER HOUSING (12c) o Flush both CHECK VALVES (12b) clean water o Assemble CHECK VALVES (12b) back into LOWER HOUSING (12c) Important: Both CHECK VALVES (12b) must be placed into
PAGE 4
5 MAINTENANCE SPRAYHEAD Caution: Place drain strainer or towel in sink drain to prevent parts from falling down the drain.  Use KEY (14) to remove SHELL (8a), SPRAYFACE (8b), aerator INSERT (8c) and WASHER (8d)  Rinse all parts with clean water to remove any debris  Replace all parts is opposite order as described above CARTRIDGE Caution: Turn off HOT and COLD supply stops before proceeding.