Installation Sheet

ManualsBrandsCalifornia Faucets ManualsShop All California FaucetsCalifornia Faucets Belmont Double Handle Valve Trim

Front View

INSTALLATION

INSTRUCTIONS

2-WAY VALVE

IMPORTANT CLEANING NOTICE Please refer to Finish Care Instructions for complete cleaning information. Wipe frequently with a soft, damp

cloth. Never use acids, harsh abrasives or detergents.

NOTE: When fitting handle it

may be necessary to shorten

broach stem and/or all thread

to eliminate gap between

handle & escutcheon.

2-VR

California Faucets reserves the right to make modification and specification changes at any time. Please visit www.calfaucets.com for most current technical data.

2V-

026

Side View

**NOTE: For Series #71, 72 & 73 valve

rough must be set back a minimum of 2-3/8”

from finished wall surface to center of inlets.

Showerhead

33"

78"

Diverter Tub Spout

2 Valve (handle) Rough

Floor Line

Tub Rim

NOTE: These are recommended

dimensions only. Always refer to local

plumbing codes prior to installation.

Twin Ell

(not supplied)

1/2" NPT Plug

Twin Ell Installation

Shower only Installation

Tub only Installation

Tub & Shower Installation

(requires twin ell not supplied)

Diverter Tub Spout

Showerhead

Tub Spout

1/2" NPT Plug

(not supplied)

Twin Ell

(not supplied)

1/2" NPT Plug

(not supplied)

1/2" NPT Plug

(not supplied)

1/2"

"A"

DIMENSION

"A" Dimension is

from finished wall

to tip of stem broach

Handle

Series # "A"

33 2-3/8"

34 2-3/8"

35 2-3/8"

36 2-3/8"

38 2-5/8"

42 2-5/8"

44 2-7/16"

45 2-1/8"

46 2-1/2"

47 2-1/2"

48 2-5/16"

50 2-1/4"

51 2-1/2"

53 2-1/4"

55 2-5/8"

57 2"

59 2-5/8"

60 2-1/4"

62 1-7/16"

63 3"

64 2-5/8"

65 2-1/8"

66 2-1/8"

67 2-1/4

68 2-3/8"

69 2-3/8"

**71 1"

**72 1"

**73 1"

NOTE: In some cases, it may be necessary to re-align cartridge

Stem

to achieve desired handle alignment. To align stem, slightly

loosen in a CCW direction the Cartridge Nut

. Place Hanlde on

Stem

and TIGHTEN in a CW direction until desired alignment

of handle is acheived. Retighten Cartrdge Nut

to factory torque

setting of 14 ft-lbs. (Cartridge Nut size is 13/16" hex)

WARNING: Cartridge Nut MUST be propler torqued to

prevent possible failure and/or water damage.

Stem

Handle

2" min

714.891.7797 Phone

714.891.2478 Fax

800.822.8855 Toll Free

californiafaucets.com

Lower Outlet:

1/2" NPT Female

to tub or twin ell

Cold Inlet:

1/2" NPT Female

Hot Inlet:

1/2" NPT Female

9-15/16"

1-1/4"

Finished Wall

All

Thread

Stem

Broach

"A" Dimension

Ø1-1/4" Opening

4-3/4"

** 2-3/8"

Cartridge

Nut

5/8"

Cartridge Nut

(13/16" hex)

Upper Outlet:

1/2" NPT Female

to shower