GigaSpire BLAST Installation Guide Model u4/u4m June 2021 Part # 220-01192 Rev 10
Contents About this Guide....................................................................... 5 Chapter 1: GigaSpire BLAST u4/u4m Overview ................... 7 GigaSpire Mesh BLAST u4m Overview ................................................................. 11 Agency Listing ......................................................................................................... 15 Site Preparation .......................................................................................................
Chapter 3: Final Set-up and Testing .................................... 29 GigaSpire BLAST u4/u4m Reset Behavior ............................................................ 29 Powering the GigaSpire BLAST u4/u4m ................................................................ 31 Connecting to the Internet ...................................................................................... 31 LED States - Power Off & Boot-up .........................................................................
About this Guide This document provides general installation practices for the Calix GigaSpire BLAST u4 (Model # GS2028E) and the GigaSpire Mesh BLAST® u4m (model # GM1028). This document also provides a general description of the products, and guidance for planning, site preparation, power installation, splicing to the outside plant, and basic troubleshooting.
Safety Notices This document uses the following safety notice conventions. DANGER! Danger indicates the presence of a hazard that will cause severe personal injury or death if not avoided. ! ! WARNING! Warning indicates the presence of a hazard that can cause severe personal injury if not avoided. CAUTION! Caution indicates the presence of a hazard that can cause minor to moderate personal injury if not avoided.
Chapter 1 GigaSpire BLAST u4/u4m Overview The Calix GigaSpire BLAST® u4 is a new generation smart home system that extends the access network into the home and acts as a strategic location for control of the ultimate WiFi experience. In addition to supporting broadband connectivity of data and video services, this intelligent, high-performance system offers the latest 802.11ax ‘Wi-Fi 6’ technology.
With Wi-Fi being the de facto wireless data communication technology of choice for consumers, Calix engineered the GigaSpire BLAST u4 for optimal whole-home coverage with simultaneous dual-band 2.4 GHz and 5 GHz operation and dynamic beamforming at 5 GHz. Leveraging the latest Wi-Fi 6 features, the GigaSpire BLAST u4 provides longer range, higher efficiency and less interference compared to earlier generations of Wi-Fi technology.
GigaSpire BLAST u4 Key Attributes - GigaSpire BLAST u4 Home Gateway Layer 2 bridge and Layer 3 routing for High Speed Internet (HSI) data and IPTV video services DHCP server options DHCP (IPoE) and PPPoE network connections Network Access Translation (NAT), public to private IP addressing Configurable IP address schemes, subnets, static-IP addresses DNS server Bridge port assignment and data traffic mappings Port forwarding Firewall and security Application and website
WI-FI 2.4 GHz and 5 GHz, simultaneous dual-band 2.4 GHz and 5 GHz 802.11ax (Wi-Fi 6) certified, 802.11a/n/ac compatible 4x4 streams (2x2 @ 2.
IPTV, IGMPv2, future support of IGMPv3: IGMP Snooping and Proxy IGMP Fast Leaves Gateway Management: Support Cloud ACS Local Home Gateway GUI, access provisionable Remote WAN side GUI access Default username/password AC to 12 VDC power adapter GigaSpire Mesh BLAST u4m Overview The Calix GigaSpire Mesh BLAST® u4m is the new generation Wi-Fi 6 mesh satellite that complements the Calix GigaSpire family of products.
MULTI-GIGABIT SUBSCRIBER EXPERIENCE The GigaSpire Mesh BLAST® u4m is a high-performance wireless satellite that delivers the latest 802.11ax Wi-Fi technology in a consumer-friendly form factor. Subscribers want their Wi-Fi to work with any device in any location throughout their home. Over time, the numbers, types and locations of these devices has exploded.
Market research projects that tens of billions of residential IoT devices will be deployed in the coming years. The GigaSpire and GigaMesh provides powerful Wi-Fi to support the growing IoT deployment. Service providers can now deploy the BLAST u4m with plug-and play Wi-Fi IoT devices such as security cameras, sensors, and smart plugs. EASY TO INSTALL, ACTIVATE AND MAINTAIN With the GigaMesh satellites, Calix has redefined how to install and activate residential services.
2x2 DL/UL MU-MIMO with beamforming 1024 QAM; OFDMA; BSS Coloring Support for 802.11k/r/v/s o 11k Radio Resource Management 11r Fast Roaming 11v Wireless Network Management Support 4-address WDS mode Support 16 SSID Replication per band 1.
AC to 12 VDC power adapter Agency Listing FCC WARNING: These devices comply with Part 15 of the FCC Rules and Regulations. Operation is subject to the following conditions. This device may not cause harmful interference, and, this device must accept any interference received, including interference that may cause undesired operation. These devices have been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules and Regulations.
Application Standards Following is a list of standards that apply to this product: Standards FCC Part 15, Sub Part B, class B UL 62368-1 EN 300 328 CAN ICES-003 Class B CSA C22.2 No. 62368-1 EN 301 893 ANSI C63.4 IEC 62368-1 EN 301 489-1 FCC Part 15.247 ITU-T K21 EN 301 489-17 FCC Part 15.203 ITU-T K44 EN 55032 Class B FCC Part 15.207 EN 62368-1 EN 61000-3-2 FCC Part 15.
GigaSpire BLAST u4 Input voltage: 12 VDC (nominal) 10 VDC (min.), 15 VDC (max) External Power Adapter: 12 VDC, 2 A GigaSpire BLAST u4m Input voltage: 12 VDC (nominal) 10 VDC (min.), 15 VDC (max) External Power Adapter: 12 VDC, 2 A DANGER! Using non-approved or incorrect power adapters can result in injury. Site Preparation Before you install any BLAST device, you need to consider the routing of the power adapter cord and Ethernet cable(s) if used.
Before you Begin Before starting the installation process, check that the following conditions are met: Ensure the site preparation steps are complete based on the model being installed. Ensure that all components are on-site or readily available to complete the installation. The customer is aware of your planned visit and will provide access to the inside of the home.
Tabletop or Wall Mount - u4 Tabletop or Wall Mount - u4m Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Power Supply (2-Pin) Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Chapter 2 Installation Installation Tips CAUTION! Use of controls or adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure. ! Follow these tips when installing a GigaSpire u4/u4m device: For subscribers using data services, all data wiring inside the home must be CAT5 cable or better. Make sure subscriber connections are tightened properly. Check the contents of each box carefully as you receive them.
Building Materials and Their Effect on Wi-Fi Signals Material Wi-Fi Attenuation Wood, Drywall, Particle Board, Tile Low Glass Low Water Medium Bricks, Cinder Block Medium Plaster, Stucco High Concrete High Tinted or Low-E Glass (metalized) Very High Metal Very High Note: The lower the attenuation, the better the performance. Installation Variables Before installing either device, consider what additional services may be implemented.
GigaSpire BLAST u4m Unpacking the GigaSpire u4/u4m Each device is shipped individually in its own carton and contains the following: (1) GigaSpire BLAST u4 or (1) GigaSpire Mesh BLAST u4m (1) Power Adapter interface cord (wall wart) (1) Safety and Regulatory Statements Guide (2) Product Identification Labels with Login Credentials After opening the carton, remove the protective packaging, ensure all components above are present, and prepare for mounting the unit.
Tabletop Mounting Dimensions Dimensions are shown here for your reference. BLAST u4/u4m 5.0 “ 12.7 cm 8292 1.5 “ 4 cm Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Wall Mounting Dimensions Dimensions for wall mounting of a GigaSpire BLAST u4 or Mesh BLAST u4m are included here for reference. Note: There is no wall mount bracket necessary to mount these devices. The bottom chassis itself includes appropriate cut-outs and hanger posts to facilitate wall mounting. Mounting Dimensions 5.0 “ 12.7 cm 2.5 “ 6.35 cm 8297 2.5 “ 6.35 cm Tabletop Mounting the u4/u4m Any Calix GigaSpire BLAST u4 or u4m can be mounted flat on a tabletop.
Note: Once the unit is connected and turned up, Wi-Fi network parameters are persisted in memory. For this reason, if power is lost to the device, it will be re-discovered on the network automatically, without operator intervention. Wall Mounting the u4/u4m The Calix GigaSpire BLAST u4 and the GigaSpire Mesh BLAST u4m can be wall mounted. Keep the following information in mind when considering wall mounting: Locate the unit on the wall in a location that is unlikely to be bumped or jostled.
Mounting Screws The two mounting holes on the back of the unit are designed to accommodate the following screw type: Larger than 7mm wide (.28") and less than 14mm wide (.55") Screw shaft < 3mm in diameter (.12") Screw length > 6mm (.24") and less than 20mm long. (.79") Depending on the material you are attaching to, use a screw of sufficient length and strength to support the GigaSpire BLAST u4/u4m once attached to the bracket. See below for specifications on what type of screw is recommended.
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Chapter 3 Final Set-up and Testing GigaSpire BLAST u4/u4m Reset Behavior Calix EDGE systems support a variety of system reset functions and provide multiple methods for invoking each of these functions, as described in this topic. Calix defines these functions and behaviors as follows: 1. Basic reset (reboot): Restarts the unit. 2. Configuration reset: Resets the RG configuration settings (those visible to the subscriber/Admin user in the EWI, such as SSIDs, LAN IP scope, etc.
Function Basic Reset Where Performed 1 Configuration Reset Hardware: Press Reset button once for 1 second Software: EWI > Utilities > Reboot Hardware: Press and hold Reset button for 15+ seconds 2 Software: EWI > Utilities > Restore Defaults Factory Reset Hardware: no option Software (for support user only): EWI > Support > Tools > Smart Activate > Factory Reset Note: For operators with cloud based network management systems, remote resets can be invoked as follows: 1 (https://www.calix.
Powering the GigaSpire BLAST u4/u4m The information below describes the powering of any GigaSpire BLAST. To power up the BLAST u4/u4m 1. Locate the 12 VDC Power Adapter. 2. Attach one end (2-pin barrel connector) to the rear of the BLAST u4/u4m. 3. Plug the other end into any available 110/220 VAC wall outlet. 4. The GigaSpire BLAST begins its start-up sequence (Flashing blue LED).
Additional Comments Once your units LED turns BLUE, you are connected to the upstream WAN modem. At start-up, Wi-Fi radios are defaulted to on. To configure your BLAST device, connect an Ethernet cable between your PC and the LAN port of your unit and enter the default IP Address of the device (192.168.1.1) into your browser. Wi-Fi radios can be configured using the default settings: SSID: Printed on the product label in the gift box. (CXNKxxxxxxxx) Number of radios: 2 (2.
LED States - BLAST LED Status BLAST LED Status Description Colors Connect to Internet Unit has successfully booted up, local services are up, and connected to the Internet Service Failure - No Internet Connection Unit is in the process of booting up or services/software is being upgraded Flashing ever 1 second assuming software can control the LED Indication CYAN Continuous Off & Red Cycles @ 1600 msec LED States - Mesh Mode Mesh BLAST u4m with BLAST u4 Description Colors Indication (
Gateway Not Found If no device is found after the initial 120 second time-out, the WPS/Strength LED bar shifts from the blinking Green to solid Red. LED bar remains red for another 60 seconds, then revert to the No Internet failure status. If pairing is accomplished, LED bar will change to reflect Gateway status.
Example Wall Mount Drilling Template Wall Mount Drilling Template, GigaSpire BLAST u4 & GigaSpire Mesh BLAST u4m Note: Do not change scale of this template. Dimensions are 1:1 Drill Here 2.50” 6.35 cm Drill Here 1.14” 2.9 cm 8311 Interface Side 220-01181 Wall Mount Drill Template for BLAST u4 & BLAST u4m, R10 Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
