User's Manual

ManualsBrandsCambium Networks ManualsElectronicsWireless Ethernet Bridge

Table Of Contents

1 About This User Guide
- 1.1 Interpreting Typeface and Other Conventions
- 1.2 Getting Additional Help
- 1.3 Sending Feedback
2 Avoiding Hazards
- 2.1 Preventing Overexposure to RF Energy
  - 2.1.1 Calculations for Separation Distances and Power Compliance Margins
    - 2.1.1.1 Calculated Distances and Power Compliance Margins
Getting Started
- For Your Safety
- 3.2 Welcome
- 3.3 Product Description
- 3.4 Warranty
4 Product Architecture
5 General Considerations
- 5.1 Spectrum Planning
- 5.2 Introducing the Time Division Duplex (TDD) Synchronization Feature
- 5.3 Region Codes
- 5.4 Operational Restrictions
- 5.5 2.5GHz Specific Frequency Planning Considerations
  - 5.5.1 Variable Channel Bandwidth Operation
  - 5.5.2 Power Reduction in the Upper Band
- 5.6 5.4GHz Specific Frequency Planning Considerations
  - 5.6.1 Raster Considerations
  - 5.6.2 Transmit Power Reduction at the Band Edges
- 5.7 5.8GHz Specific Frequency Planning Considerations
  - 5.7.1 Raster Considerations
  - 5.7.2 Transmit Power Reduction at the Band Edges
- 5.8 Distance
- 5.9 Networking Information
- 5.10 Lightning Protection
- 5.11 Electrical Requirements
6 Site Planning
- 6.1 Site Selection Criteria
7 Installation
- 7.1 Preparation
- 7.2 Installation Procedure
- 7.3 Tools Required
- 7.4 Installation Support
- 7.5 Legal Disclaimer
- 7.6 Mounting the ODUs
- 7.7 Connecting Up
8 Web Page Reference
- 8.1 Home Page – PTP 600 Series Bridge
  - 8.1.1 Home Page Alarm Display
- 8.2 Systems Status Page
- 8.3 System Administration Pages
9 Recovery Mode
- 9.1 Upgrade Software Image
- 9.2 Reset IP & Ethernet Configuration
- 9.3 Erase Configuration
- 9.4 Reboot
10 Fault Finding
- 10.1 Hardware
- 10.2 Radio
  - 10.2.1 No Activity
  - 10.2.2 Some Activity
11 Lightning Protection
- 11.1 Overview
  - 11.1.1 Lightning Protection Zones
- 11.2 Detailed Installation
- 11.3 Testing Your Installation
  - 11.3.1 Pre-Power Testing
  - 11.3.2 Post-Power Testing
12 Wind Loading
- 12.1 General
- 12.2 Calculation of Lateral Force
- 12.3 Capabilities of the PTP 600 Series Bridges
- 12.4 Wind Speed Statistics
13 PTP 600 Series Bridge – Connectorized Model
- 13.1 Scope
- 13.2 Product Description
  - 13.2.1 Hardware
  - 13.2.2 Antenna Choices – 5.8 GHz
- 13.3 Software/Features
- 13.4 Deployment Considerations
- 13.5 Link Budget
- 13.6 Regulatory Issues
  - 13.6.1 Antenna Choice (FCC Regions Only)
  - 13.6.2 Cable Losses (FCC Regions Only)
- 13.7 Antennas for USA / Canada
- 13.8 Installation
- 13.9 Additional Lightning Protection
  - 13.9.1 ODU Mounted Outdoors
  - 13.9.2 ODU Mounted Indoors
14 TDD Synchronization Configuration and Installation Guide
- 14.1 Introduction
- 14.2 TDD Synchronization Installation and Wiring Guidelines
  - 14.2.1 Installing the Recommended GPS Synchronization Kit
- 14.3 Configuring the TDD Synchronization Feature
  - 14.3.1 TDD Synchronization Enable
  - 14.3.2 TDD Synchronization Configuration Menu
    - 14.3.2.1 TDD Synchronization Configuration – Expert Mode
    - 14.3.2.2 Confirm Settings and Reboot ODU
15 E1/T1 Installation Guide
- 15.1 Preparing the PTP 600 Series Bridge E1/T1 Cable
- 15.2 Making the Connection at the ODU
- 15.3 Routing the Cable
- 15.4 Fitting a Surge Arrestor
- 15.5 Customer Cable Termination
16 Lightning Protection
- 16.1 Overview
- 16.2 Recommended Additional Components for E1/T1 Installation.
- 16.3 Surge Arrestor Wiring
- 16.4 Testing Your Installation
  - 16.4.1 Pre-Power Testing
17 Data Rate Calculations
18 AES Encryption Upgrade
- 18.1 Configuring Link Encryption
- 18.2 Configuring Link Encryption
  - 18.2.1 License Keys
  - 18.2.2 Encryption Mode and Key
- 18.3 Wireless Link Encryption FAQ
19 Legal and Regulatory Notices
- 19.1 Important Note on Modifications
- 19.2 National and Regional Regulatory Notices – 5.8 GHz variant
- 19.3 National and Regional Regulatory Notices – 5.4 GHz Variant
  - 19.3.1 U.S. Federal Communication Commission (FCC) and Industry Canada (IC) Notification
  - 19.3.2 European Union Notification
- 19.4 National and Regional Regulatory Notices – 2.5 GHz Variant
  - 19.4.1 U.S. Federal Communication Commission (FCC) Notification
- 19.5 Exposure
- 19.6 Legal Notices
20 Glossary
21 FAQs
22 Index Alar
- 23.1 System Specifications
- 23.2 Safety Compliance
- 23.3 EMC Emissions Compliance
- 23.4 EMC Immunity Compliance
- 23.5 Radio Certifications
- 23.6 Environmental Specifications
- 23.7 System Connections
  - 23.7.1 PIDU Plus to ODU and ODU to Network Equipment Connections

103

Figure 47 - Save Configuration File Screen

The configuration file is encoded using an ASCII encoding scheme. An example is show in

1074H1075HFigure 48.

Figure 48 – PTP 600 Example Configuration File