User's Manual
Table Of Contents
- 1 About This User Guide
- 2 Avoiding Hazards
- Getting Started
- For Your Safety
- 3.2 Welcome
- 3.3 Product Description
- 3.4 Warranty
- 4 Product Architecture
- 5 General Considerations
- 5.1 Spectrum Planning
- 5.2 Introducing the Time Division Duplex (TDD) Synchronization Feature
- 5.3 Region Codes
- 5.4 Operational Restrictions
- 5.5 2.5GHz Specific Frequency Planning Considerations
- 5.6 5.4GHz Specific Frequency Planning Considerations
- 5.7 5.8GHz Specific Frequency Planning Considerations
- 5.8 Distance
- 5.9 Networking Information
- 5.10 Lightning Protection
- 5.11 Electrical Requirements
- 6 Site Planning
- 6.1 Site Selection Criteria
- 6.1.1 ODU Site Selection
- 6.1.2 PTP 600 Series Bridge PIDU Plus Site Selection
- 6.1.3 Path Loss Considerations
- 6.1.4 Definitions
- 6.1.5 2.5 GHz Product Variant - Receive Sensitivity, Link Loss, Output Power and Threshold Vs Modulation Mode
- 6.1.6 5.4 GHz Product Variant - Receive Sensitivity, Link Loss, Output Power and Threshold Vs Modulation Mode
- 6.1.7 5.8 GHz Product Variant - Receive Sensitivity, Link Loss, Output Power and Threshold Vs Modulation Mode
- 6.1 Site Selection Criteria
- 7 Installation
- 7.1 Preparation
- 7.2 Installation Procedure
- 7.3 Tools Required
- 7.4 Installation Support
- 7.5 Legal Disclaimer
- 7.6 Mounting the ODUs
- 7.7 Connecting Up
- 7.7.1 Preparing The PIDU Plus To ODU Cable
- 7.7.2 Making the Connections at the ODU
- 7.7.3 Making the PTP 600 Series Bridge PIDU Plus Connection At The ODU
- 7.7.4 Routing the Cable
- 7.7.5 Fitting A Surge Arrestor
- 7.7.6 Grounding the Installation
- 7.7.7 Making the ODU Connection at the PTP 600 Series Bridge PIDU Plus
- 7.7.8 Making the Network Connection at The PIDU Plus – PTP 600 Series Bridge
- 7.7.9 Mounting the PTP 600 Series Bridge PIDU Plus
- 7.7.10 Powering Up
- 7.7.11 Aligning the PTP 600 Series Bridge ODUs
- 8 Web Page Reference
- 8.1 Home Page – PTP 600 Series Bridge
- 8.2 Systems Status Page
- 8.3 System Administration Pages
- 8.3.1 System Configuration
- 8.3.2 Statistics Page
- 8.3.3 Detailed Counters Page
- 8.3.4 Install Pages
- 8.3.5 Graphical Install
- 8.3.6 Software Upgrade
- 8.3.7 Spectrum Management
- 8.3.7.1 Wireless Channels
- 8.3.7.2 Spectrum Management Measurements
- 8.3.7.3 Measurement Analysis
- 8.3.7.4 The Spectrum Management Master / Slave Relationship
- 8.3.7.5 Spectrum Management Configuration
- 8.3.7.6 Barring Channels
- 8.3.7.7 Local and Peer Channel Spectrum Graphics
- 8.3.7.8 Active Channel History
- 8.3.7.9 Viewing Historic Spectrum Management Metrics
- 8.3.8 Spectrum Management (Fixed Frequency and WIMAX)
- 8.3.9 Spectrum Management Control - With Operational Restrictions
- 8.3.10 Spectrum Management – Example of 2.5 GHz Product variant
- 8.3.11 Remote Management Page
- 8.3.12 Diagnostics
- 8.3.13 Change System Administration Password
- 8.3.14 License Key
- 8.3.15 Properties
- 8.3.16 Reboot
- 9 Recovery Mode
- 10 Fault Finding
- 11 Lightning Protection
- 12 Wind Loading
- 13 PTP 600 Series Bridge – Connectorized Model
- 13.1 Scope
- 13.2 Product Description
- 13.3 Software/Features
- 13.4 Deployment Considerations
- 13.5 Link Budget
- 13.6 Regulatory Issues
- 13.7 Antennas for USA / Canada
- 13.8 Installation
- 13.8.1 Antenna Choice
- 13.8.2 Cables and Connectors
- 13.8.3 Tools
- 13.8.4 Miscellaneous supplies
- 13.8.5 Mounting the Connectorized 600 Series Bridge
- 13.8.6 Mounting the antennas
- 13.8.7 Alignment Process
- 13.8.8 Aligning Dual Polar Antennas
- 13.8.9 Aligning Separate Antennas
- 13.8.10 Completing the Installation
- 13.8.11 Antenna Cable Fixing
- 13.8.12 Antenna Connection Weatherproofing
- 13.9 Additional Lightning Protection
- 14 TDD Synchronization Configuration and Installation Guide
- 15 E1/T1 Installation Guide
- 16 Lightning Protection
- 17 Data Rate Calculations
- 18 AES Encryption Upgrade
- 19 Legal and Regulatory Notices
- 20 Glossary
- 21 FAQs
- 22 Index Alar
64
6.1.5 2.5 GHz Product Variant - Receive Sensitivity, Link Loss, Output Power and Threshold Vs
Modulation Mode
The equipment capability is given in
1020HTable 10. This table gives Receive Sensitivity, Link Loss
and Output Power for PTP 600 Series Bridge in all modulation modes for channel bandwidth
equal to 30 MHz. Adaptive modulation will ensure that the highest throughput that can be
achieved instantaneously will be obtained taking account of propagation and interference.
The calculation of
1021HEquation 1 needs to be performed to judge whether a particular link can be
installed. When the link has been installed, web pages provide information about the link loss
currently measured by the equipment both instantaneously and averaged. The averaged
value will require maximum seasonal fading to be added, and then the radio reliability of the
link can be computed.
Threshold
V
alue
(
dBm
)
Output
Power
(
dBm
)
Maximum
Link Loss
(
dB
)
Channel Bandwidth (MHz)
Modulation Mode
5
MHz
10
MHz
15
MHz
30
MHz
All
Bandwidths
5
MHz
10
MHz
15
MHz
30
MHz
BPSK 0.63 single -97.95 -95.25 -91.36 -88.9 +23 158.0 155.3 151.4 150.1
QPSK 0.63 single
-96.29 -93.76 -85.17 -85.4 +23 151.2 148.9 145.2 144.5
QPSK 0.87 single
-93.79 -90.38 -81.06 -82.4 +23 148.0 144.5 141.1 140.6
16QAM 0.63 single
-91.49 -88.25 -79.20 -80.1 +23 145.6 142.4 139.2 138.5
16QAM 0.63 dual
-88.69 -84.55 -76.21 -77.0 +23 143.0 138.9 136.2 135.6
16QAM 0.87 single
-86.83 -83.59 -73.28 -75.9 +23 140.5 136.5 133.3 132.6
16QAM 0.87 dual
-84.16 -80.29 -70.08 -71.8 +23 137.2 132.6 130.1 129.1
64QAM 0.75 single
-84.69 -81.37 -70.38 -73.0 +23 137.5 133.6 130.4 129.7
64QAM 0.75 dual
-81.77 -77.83 -67.01 -68.6 +23 134.3 129.4 127.0 126.1
64QAM 0.92 single
-80.36 -76.93 -68.62 -67.6 +23 135.1 131.7 128.6 130.6
64 QAM 0.92 dual
-77.33 -73.87 -65.19 -63.9 +23 132.4 127.6 125.2 124.3
256QAM 0.81 single
-77.92 -74.50 -65.50 -65.4 +23 132.3 132.4 125.5 124.6
256QAM 0.81 dual -75.28 -71.24 -62.24 -61.0 +23 129.4 128.1 122.2 120.5
Table 10 - 2.5GHz – Receive Sensitivity, Link Loss, Output Power and Threshold Vs
Modulation Mode