User's Guide
Table Of Contents
- PTP 500 Series User Guide
- Copyright Information
- Disclaimer
- Contents
- List of Figures
- List of Tables
- List of Equations
- 1 About This User Guide
- 2 Product Description
- 2.1 Product Function
- 2.2 Typical Deployment
- 2.3 Frequency Variants
- 2.4 Other Product Variants
- 2.5 Network Connection
- 2.6 Outdoor Unit (ODU)
- 2.7 PIDU Plus PTP 300/500/600 Series
- 2.8 Redundancy and Alternative Powering Configurations
- 2.9 Remote LEDs and Recovery Switch
- 2.10 Cables and Connectors
- 2.11 PTP and Lightning Protection
- 2.12 Mounting Brackets
- 3 Product Features
- 4 Planning Considerations
- 5 Lightning Protection
- 6 Installation
- 6.1 Installation Support
- 6.2 Legal Disclaimer
- 6.3 Preparation
- 6.4 Mounting the ODUs
- 6.5 Connecting Up
- 6.5.1 Preparing the PIDU Plus To ODU Cable
- 6.5.2 Making the Connections at the ODU
- 6.5.3 Making the PIDU Plus Connection At The ODU
- 6.5.4 Routing the Cable
- 6.5.5 Fitting a Lightning Protection Unit
- 6.5.6 Grounding the Installation
- 6.5.7 Making the ODU Connection at the PIDU Plus
- 6.5.8 Making the Network Connection at the PIDU Plus
- 6.5.9 Mounting the PIDU Plus
- 6.5.10 Powering Up
- 6.6 Establishing a Radio Link
- 7 Web Page Reference
- 7.1 Menu Navigation Bar
- 7.2 Home (System Summary)
- 7.3 System Status
- 7.4 System Administration
- 7.5 Configuration
- 7.6 Statistics
- 7.7 Installation Wizard
- 7.8 Software Upgrade
- 7.9 Spectrum Management
- 7.9.1 Wireless Channels
- 7.9.2 Spectrum Management Measurements
- 7.9.3 Measurement Analysis
- 7.9.4 The Spectrum Management Master / Slave Relationship
- 7.9.5 Spectrum Management Configuration
- 7.9.6 Barring Channels
- 7.9.7 Master and Slave Channel Spectrum Graphics
- 7.9.8 Active Channel History
- 7.9.9 Viewing Historic Spectrum Management Metrics
- 7.9.10 Spectrum Management (Fixed Frequency)
- 7.9.11 Spectrum Management Control with Radar Avoidance
- 7.10 Remote Management
- 7.10.1 Control Access to HTTP Interface
- 7.10.2 Control Access to Telnet Interface
- 7.10.3 SNMP (Simple Network Management Protocol)
- 7.10.4 Supported Management Information Bases (MIBS)
- 7.10.5 Diagnostics Alarms
- 7.10.6 SNMP Configuration
- 7.10.7 SMTP (Simple Mail Transport Protocol)
- 7.10.8 SNTP (Simple Network Time Protocol)
- 7.10.9 Setting the clock
- 7.11 Diagnostics Plotter
- 7.12 Change Password
- 7.13 License Key
- 7.14 Properties
- 7.15 Reboot
- 8 Recovery Mode
- 9 Troubleshooting (Fault Finding)
- 10 Connectorized PTP 500 Series Bridge
- 10.1 Product Description
- 10.2 Software/Features
- 10.3 Deployment Considerations
- 10.4 Link Budget
- 10.5 Regulatory Issues with Connectorized Units
- 10.6 Antenna Choices
- 10.7 Installation
- 10.7.1 Cables and Connectors
- 10.7.2 Tools
- 10.7.3 Miscellaneous supplies
- 10.7.4 Mounting the Connectorized PTP 500 Series Bridge
- 10.7.5 Mounting the antennas
- 10.7.6 Alignment Process
- 10.7.7 Aligning Dual Polar Antennas
- 10.7.8 Aligning Separate Antennas
- 10.7.9 Completing the Installation
- 10.7.10 Antenna Cable Fixing
- 10.7.11 Antenna Connection Weatherproofing
- 10.8 Additional Lightning Protection
- 11 E1/T1 Installation Guide
- 12 Data Rate Calculations
- 13 AES Encryption
- 14 Remote Software Upgrade by TFTP
- 15 Legal Notices
- 15.1 Motorola Inc. End User License Agreement
- 15.1.1 Definitions
- 15.1.2 Grant of License
- 15.1.3 Conditions of Use
- 15.1.4 Title; Restrictions
- 15.1.5 Confidentiality
- 15.1.6 Right to Use Motorola’s Name
- 15.1.7 Transfer
- 15.1.8 Updates
- 15.1.9 Maintenance
- 15.1.10 Disclaimer
- 15.1.11 Limitation of Liability
- 15.1.12 U.S. Government
- 15.1.13 Term of License
- 15.1.14 Governing Law
- 15.1.15 Assignment
- 15.1.16 Survival of Provisions
- 15.1.17 Entire Agreement
- 15.1.18 Third Party Software
- 15.2 Hardware Warranty in U.S.
- 15.3 Limit of Liability
- 15.1 Motorola Inc. End User License Agreement
- 16 PTP 500 Reference Information
- 16.1 PTP 500 General Reference Information
- 16.2 PTP 54500 Reference Information
- 16.2.1 PTP 54500 Examples of Regulatory Limits
- 16.2.2 PTP 54500 Licenses and Region Codes
- 16.2.3 PTP 54500 Regulatory Compliance
- 16.2.4 PTP 54500 Radio System Specifications
- 16.2.5 PTP 54500 Emissions and Radio Certifications
- 16.2.6 PTP 54500 Available Spectrum Settings
- 16.2.7 PTP 54500 System Threshold, Output Power and Link Loss
- 16.2.8 PTP 54500 FCC Antenna Restrictions
- 16.3 PTP 58500 Reference Information
- 16.3.1 PTP 58500 Examples of Regulatory Limits
- 16.3.2 PTP 58500 Licenses and Region Codes
- 16.3.3 PTP 58500 Regulatory Compliance
- 16.3.4 PTP 58500 Radio System Specifications
- 16.3.5 PTP 58500 Emissions and Radio Certifications
- 16.3.6 PTP 58500 Available Spectrum Settings
- 16.3.7 PTP 58500 System Threshold, Output Power and Link Loss
- 16.3.8 PTP 58500 FCC Antenna Restrictions
- 17 FAQs
- 18 Glossary
7 Web Page Reference
83
Half Duplex data transmission means that data can be transmitted in both directions on a
signal carrier, but not at the same time. For example, on a local area network using a
technology that has half duplex transmission, one workstation can send data on the line and
then immediately receive data on the line from the same direction in which data was just
transmitted.
MAC Address
MAC address of the unit.
Remote MAC Address
MAC address of the remote unit.
Remote IP Address
Hyperlink to the other side of the Link. The IP address of the peer link is displayed if the Link
is UP, otherwise “unavailable” is displayed.
Telecoms Status
Indicates the current status of the telecoms channel. Channels which are disabled during
installation are marked as such. Correctly operating channels display "Up" on a green
background, but alarm conditions (described in Section 7.2.1 “Home Page Alarm Display”)
have a re
d background.
Telecoms Latency
If E1 or T1 is enabled, this shows the end-to-end latency of the telecoms link.
Automatic Page Refresh Period in Seconds
Only displayed when the user is logged on as system administrator. Enter the required refresh
period.
Wireless Link Status
As the attribute name suggests it displays the current status of the wireless link. A state of
‘Up’ on a green background indicates that a point-to-point link is established. A state of ‘Down’
on a red background indicates that the wireless link is not established.
Maximum Transmit Power
The maximum transmit power that the local wireless unit is permitted to use to sustain a link.
Remote Maximum Transmit Power
The maximum transmit power that the remote wireless unit is permitted to use to sustain a
link.
Transmit Power
Transmit power histogram is expressed in dBm and presented as: max, mean, min, and
latest. The max, min and latest are true instantaneous measurements; the mean is the mean
of a set of one second means. The Transmit Power may be less than the maximum permitted
Transmit Power due to the TPC (Transmit Power Control) mechanism. This mechanism
adjusts Transmit Power to achieve best link performance while minimizing the interference it
causes to other users of this part of the Spectrum. See Section 7.3.1 “Histogram Data”.
Rec
eive Power
Receive power histogram is expressed in dBm and presented as: max, mean, min, and latest.
The max, min and latest are true instantaneous measurements; the mean is the mean of a set
of one second means. See Section 7.3.1 “Histogram Data”.