User's Guide
Table Of Contents
- PTP 500 Series User Guide
- Copyright Information
- Disclaimer
- Contents
- List of Figures
- List of Tables
- List of Equations
- 1 About This User Guide
- 2 Product Description
- 2.1 Product Function
- 2.2 Typical Deployment
- 2.3 Frequency Variants
- 2.4 Other Product Variants
- 2.5 Network Connection
- 2.6 Outdoor Unit (ODU)
- 2.7 PIDU Plus PTP 300/500/600 Series
- 2.8 Redundancy and Alternative Powering Configurations
- 2.9 Remote LEDs and Recovery Switch
- 2.10 Cables and Connectors
- 2.11 PTP and Lightning Protection
- 2.12 Mounting Brackets
- 3 Product Features
- 4 Planning Considerations
- 5 Lightning Protection
- 6 Installation
- 6.1 Installation Support
- 6.2 Legal Disclaimer
- 6.3 Preparation
- 6.4 Mounting the ODUs
- 6.5 Connecting Up
- 6.5.1 Preparing the PIDU Plus To ODU Cable
- 6.5.2 Making the Connections at the ODU
- 6.5.3 Making the PIDU Plus Connection At The ODU
- 6.5.4 Routing the Cable
- 6.5.5 Fitting a Lightning Protection Unit
- 6.5.6 Grounding the Installation
- 6.5.7 Making the ODU Connection at the PIDU Plus
- 6.5.8 Making the Network Connection at the PIDU Plus
- 6.5.9 Mounting the PIDU Plus
- 6.5.10 Powering Up
- 6.6 Establishing a Radio Link
- 7 Web Page Reference
- 7.1 Menu Navigation Bar
- 7.2 Home (System Summary)
- 7.3 System Status
- 7.4 System Administration
- 7.5 Configuration
- 7.6 Statistics
- 7.7 Installation Wizard
- 7.8 Software Upgrade
- 7.9 Spectrum Management
- 7.9.1 Wireless Channels
- 7.9.2 Spectrum Management Measurements
- 7.9.3 Measurement Analysis
- 7.9.4 The Spectrum Management Master / Slave Relationship
- 7.9.5 Spectrum Management Configuration
- 7.9.6 Barring Channels
- 7.9.7 Master and Slave Channel Spectrum Graphics
- 7.9.8 Active Channel History
- 7.9.9 Viewing Historic Spectrum Management Metrics
- 7.9.10 Spectrum Management (Fixed Frequency)
- 7.9.11 Spectrum Management Control with Radar Avoidance
- 7.10 Remote Management
- 7.10.1 Control Access to HTTP Interface
- 7.10.2 Control Access to Telnet Interface
- 7.10.3 SNMP (Simple Network Management Protocol)
- 7.10.4 Supported Management Information Bases (MIBS)
- 7.10.5 Diagnostics Alarms
- 7.10.6 SNMP Configuration
- 7.10.7 SMTP (Simple Mail Transport Protocol)
- 7.10.8 SNTP (Simple Network Time Protocol)
- 7.10.9 Setting the clock
- 7.11 Diagnostics Plotter
- 7.12 Change Password
- 7.13 License Key
- 7.14 Properties
- 7.15 Reboot
- 8 Recovery Mode
- 9 Troubleshooting (Fault Finding)
- 10 Connectorized PTP 500 Series Bridge
- 10.1 Product Description
- 10.2 Software/Features
- 10.3 Deployment Considerations
- 10.4 Link Budget
- 10.5 Regulatory Issues with Connectorized Units
- 10.6 Antenna Choices
- 10.7 Installation
- 10.7.1 Cables and Connectors
- 10.7.2 Tools
- 10.7.3 Miscellaneous supplies
- 10.7.4 Mounting the Connectorized PTP 500 Series Bridge
- 10.7.5 Mounting the antennas
- 10.7.6 Alignment Process
- 10.7.7 Aligning Dual Polar Antennas
- 10.7.8 Aligning Separate Antennas
- 10.7.9 Completing the Installation
- 10.7.10 Antenna Cable Fixing
- 10.7.11 Antenna Connection Weatherproofing
- 10.8 Additional Lightning Protection
- 11 E1/T1 Installation Guide
- 12 Data Rate Calculations
- 13 AES Encryption
- 14 Remote Software Upgrade by TFTP
- 15 Legal Notices
- 15.1 Motorola Inc. End User License Agreement
- 15.1.1 Definitions
- 15.1.2 Grant of License
- 15.1.3 Conditions of Use
- 15.1.4 Title; Restrictions
- 15.1.5 Confidentiality
- 15.1.6 Right to Use Motorola’s Name
- 15.1.7 Transfer
- 15.1.8 Updates
- 15.1.9 Maintenance
- 15.1.10 Disclaimer
- 15.1.11 Limitation of Liability
- 15.1.12 U.S. Government
- 15.1.13 Term of License
- 15.1.14 Governing Law
- 15.1.15 Assignment
- 15.1.16 Survival of Provisions
- 15.1.17 Entire Agreement
- 15.1.18 Third Party Software
- 15.2 Hardware Warranty in U.S.
- 15.3 Limit of Liability
- 15.1 Motorola Inc. End User License Agreement
- 16 PTP 500 Reference Information
- 16.1 PTP 500 General Reference Information
- 16.2 PTP 54500 Reference Information
- 16.2.1 PTP 54500 Examples of Regulatory Limits
- 16.2.2 PTP 54500 Licenses and Region Codes
- 16.2.3 PTP 54500 Regulatory Compliance
- 16.2.4 PTP 54500 Radio System Specifications
- 16.2.5 PTP 54500 Emissions and Radio Certifications
- 16.2.6 PTP 54500 Available Spectrum Settings
- 16.2.7 PTP 54500 System Threshold, Output Power and Link Loss
- 16.2.8 PTP 54500 FCC Antenna Restrictions
- 16.3 PTP 58500 Reference Information
- 16.3.1 PTP 58500 Examples of Regulatory Limits
- 16.3.2 PTP 58500 Licenses and Region Codes
- 16.3.3 PTP 58500 Regulatory Compliance
- 16.3.4 PTP 58500 Radio System Specifications
- 16.3.5 PTP 58500 Emissions and Radio Certifications
- 16.3.6 PTP 58500 Available Spectrum Settings
- 16.3.7 PTP 58500 System Threshold, Output Power and Link Loss
- 16.3.8 PTP 58500 FCC Antenna Restrictions
- 17 FAQs
- 18 Glossary
2 Product Description
20
2.7.2 ODU, LAN and Recovery
At the bottom of the PIDU Plus is an entry point for the PIDU Plus to ODU cable, the
100BaseT Ethernet network port and the Recovery switch.
Figure 4 – PIDU Plus Recovery Switch Location
The Recovery switch is used to recover the unit from configuration errors or software image
corruption. To put an ODU into recovery mode, the Recovery switch should be pressed, then
the power applied. The Recovery switch should be kept pressed for at least 30 seconds after
the power has been applied. Full instruction on the recovery mode can be found in Section 8
“Recovery Mode”.
A simple re
boot can be performed by removing and re-applying the mains power to the PIDU
Plus.
2.7.3 DC In and Out
On the left hand side of the PIDU Plus, 48V DC input and output connections can be found.
These are used to power the PTP 500 Series Bridge from an external DC source or to
provide a level of power supply redundancy, as shown in Section 2.8 “Redundancy and
Alternative Powe
ring Configurations”.
2.7.4 Remote Connectors and Jumpers
Also on the left hand side of the PIDU Plus, connectors and jumpers can be found that allow
the remote connection of power LED, Ethernet LED and Recovery switch. The connection
instructions can be found in Section 2.9 “Remote LEDs and Recovery Switch”.