User's Guide
Table Of Contents
- PTP 500 Series User Guide
- Copyright Information
- Disclaimer
- Contents
- List of Figures
- List of Tables
- List of Equations
- 1 About This User Guide
- 2 Product Description
- 2.1 Product Function
- 2.2 Typical Deployment
- 2.3 Frequency Variants
- 2.4 Other Product Variants
- 2.5 Network Connection
- 2.6 Outdoor Unit (ODU)
- 2.7 PIDU Plus PTP 300/500/600 Series
- 2.8 Redundancy and Alternative Powering Configurations
- 2.9 Remote LEDs and Recovery Switch
- 2.10 Cables and Connectors
- 2.11 PTP and Lightning Protection
- 2.12 Mounting Brackets
- 3 Product Features
- 4 Planning Considerations
- 5 Lightning Protection
- 6 Installation
- 6.1 Installation Support
- 6.2 Legal Disclaimer
- 6.3 Preparation
- 6.4 Mounting the ODUs
- 6.5 Connecting Up
- 6.5.1 Preparing the PIDU Plus To ODU Cable
- 6.5.2 Making the Connections at the ODU
- 6.5.3 Making the PIDU Plus Connection At The ODU
- 6.5.4 Routing the Cable
- 6.5.5 Fitting a Lightning Protection Unit
- 6.5.6 Grounding the Installation
- 6.5.7 Making the ODU Connection at the PIDU Plus
- 6.5.8 Making the Network Connection at the PIDU Plus
- 6.5.9 Mounting the PIDU Plus
- 6.5.10 Powering Up
- 6.6 Establishing a Radio Link
- 7 Web Page Reference
- 7.1 Menu Navigation Bar
- 7.2 Home (System Summary)
- 7.3 System Status
- 7.4 System Administration
- 7.5 Configuration
- 7.6 Statistics
- 7.7 Installation Wizard
- 7.8 Software Upgrade
- 7.9 Spectrum Management
- 7.9.1 Wireless Channels
- 7.9.2 Spectrum Management Measurements
- 7.9.3 Measurement Analysis
- 7.9.4 The Spectrum Management Master / Slave Relationship
- 7.9.5 Spectrum Management Configuration
- 7.9.6 Barring Channels
- 7.9.7 Master and Slave Channel Spectrum Graphics
- 7.9.8 Active Channel History
- 7.9.9 Viewing Historic Spectrum Management Metrics
- 7.9.10 Spectrum Management (Fixed Frequency)
- 7.9.11 Spectrum Management Control with Radar Avoidance
- 7.10 Remote Management
- 7.10.1 Control Access to HTTP Interface
- 7.10.2 Control Access to Telnet Interface
- 7.10.3 SNMP (Simple Network Management Protocol)
- 7.10.4 Supported Management Information Bases (MIBS)
- 7.10.5 Diagnostics Alarms
- 7.10.6 SNMP Configuration
- 7.10.7 SMTP (Simple Mail Transport Protocol)
- 7.10.8 SNTP (Simple Network Time Protocol)
- 7.10.9 Setting the clock
- 7.11 Diagnostics Plotter
- 7.12 Change Password
- 7.13 License Key
- 7.14 Properties
- 7.15 Reboot
- 8 Recovery Mode
- 9 Troubleshooting (Fault Finding)
- 10 Connectorized PTP 500 Series Bridge
- 10.1 Product Description
- 10.2 Software/Features
- 10.3 Deployment Considerations
- 10.4 Link Budget
- 10.5 Regulatory Issues with Connectorized Units
- 10.6 Antenna Choices
- 10.7 Installation
- 10.7.1 Cables and Connectors
- 10.7.2 Tools
- 10.7.3 Miscellaneous supplies
- 10.7.4 Mounting the Connectorized PTP 500 Series Bridge
- 10.7.5 Mounting the antennas
- 10.7.6 Alignment Process
- 10.7.7 Aligning Dual Polar Antennas
- 10.7.8 Aligning Separate Antennas
- 10.7.9 Completing the Installation
- 10.7.10 Antenna Cable Fixing
- 10.7.11 Antenna Connection Weatherproofing
- 10.8 Additional Lightning Protection
- 11 E1/T1 Installation Guide
- 12 Data Rate Calculations
- 13 AES Encryption
- 14 Remote Software Upgrade by TFTP
- 15 Legal Notices
- 15.1 Motorola Inc. End User License Agreement
- 15.1.1 Definitions
- 15.1.2 Grant of License
- 15.1.3 Conditions of Use
- 15.1.4 Title; Restrictions
- 15.1.5 Confidentiality
- 15.1.6 Right to Use Motorola’s Name
- 15.1.7 Transfer
- 15.1.8 Updates
- 15.1.9 Maintenance
- 15.1.10 Disclaimer
- 15.1.11 Limitation of Liability
- 15.1.12 U.S. Government
- 15.1.13 Term of License
- 15.1.14 Governing Law
- 15.1.15 Assignment
- 15.1.16 Survival of Provisions
- 15.1.17 Entire Agreement
- 15.1.18 Third Party Software
- 15.2 Hardware Warranty in U.S.
- 15.3 Limit of Liability
- 15.1 Motorola Inc. End User License Agreement
- 16 PTP 500 Reference Information
- 16.1 PTP 500 General Reference Information
- 16.2 PTP 54500 Reference Information
- 16.2.1 PTP 54500 Examples of Regulatory Limits
- 16.2.2 PTP 54500 Licenses and Region Codes
- 16.2.3 PTP 54500 Regulatory Compliance
- 16.2.4 PTP 54500 Radio System Specifications
- 16.2.5 PTP 54500 Emissions and Radio Certifications
- 16.2.6 PTP 54500 Available Spectrum Settings
- 16.2.7 PTP 54500 System Threshold, Output Power and Link Loss
- 16.2.8 PTP 54500 FCC Antenna Restrictions
- 16.3 PTP 58500 Reference Information
- 16.3.1 PTP 58500 Examples of Regulatory Limits
- 16.3.2 PTP 58500 Licenses and Region Codes
- 16.3.3 PTP 58500 Regulatory Compliance
- 16.3.4 PTP 58500 Radio System Specifications
- 16.3.5 PTP 58500 Emissions and Radio Certifications
- 16.3.6 PTP 58500 Available Spectrum Settings
- 16.3.7 PTP 58500 System Threshold, Output Power and Link Loss
- 16.3.8 PTP 58500 FCC Antenna Restrictions
- 17 FAQs
- 18 Glossary
4 Planning Considerations
32
4 Planning Considerations
This section provides information to help the user to plan a PTP 500 link.
Each frequency variant has specific licensing restrictions that affect frequency range, channel
bandwidth, maximum power and radar avoidance. Link planning must take account of
obstructions, site selection, path loss and wind loading.
The following topics are described in this section:
• 4.1 Spectrum Planning
• 4.2 Licenses and Region Codes
• 4.3 Radar Avoidance and Bandwidth Operation
• 4.4 Variable Channel Bandwidth Operation
• 4.5 Link Planning
• 4.6 Site Selection Criteria
• 4.7 Wind Loading
• 4.8 Path Loss Considerations
• 4.9 System Threshold, Output Power and Link Loss
To calculate
the data throughput capacity of a planned PTP 500 link, see Section 12 “Data
Rate Calculat
ions”.
4.1 Spectrum Planning
The PTP 500 may use one of four alternative methods of spectrum planning. The choice of
methods depends upon whether or not the region mandates radar detection.
4.1.1 Regions Without Mandatory Radar Detection
In regions that do not mandate DFS (Radar Detection), the frequencies may be configured
symmetrically or asymmetrically (different transmit and receive frequencies). The Spectrum
Management Control options are:
• Intelligent Dynamic Frequency Selection (i-DFS): This method continually monitors the
spectrum looking for the channel with the lowest level of on channel and co-channel
interference. Statistical techniques are used to select the most appropriate transmit and
receive channels. The i-DFS mode can be influenced in its channel decision process by
selectively barring channels from use.