Rearview Mirror with 4.5" Color LCD with Navigation and 2 Camera inputs Model: LCMR5RP Installation Manual Features: • Rearview Mirror with 4.
Cautions! The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle.
TABLE OF CONTENTS Cautions! 1 Preface 3 WARNING 3 Packing list 3 1.Installation Instructions 4 2.Signal Inputs 5 3.
Preface This replacement mirror /monitor can display up to 3 different video inputs. The inputs are Navigation, Rear observation camera and Interior observation camera. Not all rearview mirrors attach to the vehicle with the same style mount. Please consult the application guide for the appropriate mounting bracket for your vehicle or call Tech Service at 800-225-6074. There is a blind spot that exists at the back of a vehicle while the vehicle is in reverse.
1. Installation Instructions (1) Mount the mirror/monitor a) Remove the original factory mirror. (Do not use excessive force when removing factory mirror.) Check to make sure that the factory mirror mount you remove matches the mirror mount on the replacement mirror. If it does not match, consult the application guide or call Technical Service at 800-225-6074. b) Slide the receiving bracket on the back of the new mirror stalk onto the windshield mounting button.
(4) Electrical Connections: Connect the 4 wires in the following manner. a) Red wire - 12 volt constant (positive) b) Black wire - Chassis ground (negative) c) Blue wire - 12-volt ignition (12 volt with ignition on) d) Green wire - Reverse light switch (12 volt when vehicle is in the reverse gear) WARNING: Observe polarity when connecting the wires. Figure 2 2.
Some operators may find that leaving the Navigation Image on the LCD monitor at all times becomes a distraction while operating their motor vehicle. For the convenience of those operators, a ‘Display Timer Slide Control Switch’ has been added to the mirror. A. When the Slide Control Switch is moved to the far right end position, the Navigation image will remain on at all times. B. When the Slide Control Switch is moved to the far left end position, the Navigation image will remain off at all times. C.
Figure 5 3. Controls and Indicators Figure 5 shows the function controls of the rear view mirror. A: 4.5" LCD Panel B: Rearview Mirror Glass C: “+”Button (optional Navigation System required) Incrementally increase volume level of the navigation voice command when pressed. Note: Will only operate when the Navigation System remote control is removed from the cradle.
Note: Will only operate when the Navigation System remote control is removed from the cradle. F: “-” Button (optional Navigation System required) Incrementally decrease volume level of the navigation voice command when pressed. Note: Will only operate when the Navigation System remote control is removed from the cradle. G: Internal Speaker H: LCD Brightness Control I: Internal Infra-RED Receiver for use with Navigation System Remote Control.
Specifications General Power Supply 12VDC Power Consumption <12W Current Draw <800mA Video Input 1Vp-p/ 75 Impedance Audio Input <=1V Audio Power Output 0.5W × 1 (16Ω) Operating Temperature Range 0℃ to 50℃ Display System Screen 4.
Maintenance Though your Rearview mirror requires little care, you can still maintain its condition and performance by following the procedures below. • Keep your system away from excessive moisture, extreme heat or cold, and magnetic fields. • Keep liquids away from the display and mirror. • To avoid damage, do not place external devices or other objects on the top of the mirror. • Occasionally wipe the rearview mirror set with a soft, damp cloth.
Troubleshooting Symptoms The ON/OFF signal light is not on after the car is started? Solutions 1. 2. 3. 1. 2. No video signal appears while reversing the car? 3. 4. Check the installation-wiring diagram. Ensure that the parallel red and black line from the control box is connected properly. Check for 12 volts on the blue wire while the ignition on. Check the rearview Camera lens. Check the rearview Camera wiring and connection.
Illustration of Connections Figure 6 12
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y.