KP10 A-BUS keypad Installation Guide
CONTENTS Introduction.......................................................3 System options.................................................4 Installation notes..............................................8 Rear panel connections.................................10 Keypad controls..............................................12 Operating instructions....................................14 Local source selection....................................16 Remote control.............................................
KP10 A-BUS keypad INTRODUCTION Thank you for purchasing this Cambridge Audio Incognito product. Incognito is a cost-effective, modular based system using standard Cat-5 or Cat-6 cable to distribute hi-fi quality sound and video around a home. The KP10 is an in-wall, A-BUS TM compatible amplified keypad with buttons for control of speaker volume levels, Standby/On and source select (with compatible equipment), as well as having an IR window for receiving remote control signals.
SYSTEM OPTIONS The KP10 keypad can be used in two main configurations: 1. As part of a full Incognito system, where it is plugged into an Incognito hub (AH10), perhaps with other Incognito accessories such as a video switching unit (VH10) or local input module (LM10) fitted. 2.
KP10 A-BUS keypad SS10 SS10 Speaker cable Speaker cable KP10-EU KP10-EU Cat-5/5e cable AH10 PS10 Incognito A-BUS keypad 5
A-BUS Ready / Incognito Ready For use with an A-BUS Ready/Incognito Ready unit (see diagram opposite) the Mode switch MUST be in the "Standard A-BUS/Incognito Ready" position as shown below: KP10-EU rear Mode Std. A-BUS/ Incognito Ready AH10 Mode Std. A-BUS/ Incognito Ready AH10 In this configuration the keypad is wired directly to the amplifier/receiver. A Power Supply Unit (PS10) is also required to power the one or two keypads as shown.
KP10 A-BUS keypad SS10 SS10 Speaker cable Speaker cable LR10 KP10-EU KP10-EU Cat5/5e cable PS10 CAP5 Multi-Room Protection LED indicators: IR1 IR3 IR2 IR4 azur 640A Integrated Amplifier V2.0 Impedance 4 - 8 ohms Right Left A Off B On Left Power Designed in London, England www.cambridge-audio.
INSTALLATION NOTES The KP10 is fitted on the wall by fixing it into a standard UK 47mm depth single-gang electrician’s back-box (pattress). All knock-outs in the back-box should be removed to provide maximum ventilation. Where it is desired to fit a mains lighting switch etc next to a keypad, a barrier-box or two single back-boxes must be used (bear in mind it is not preferable to fit the keypad next to a light-switch particularly if the faceplate styles will differ).
KP10 A-BUS keypad Safety precautions Care should be taken when choosing the site for a KP10, the keypad must never be installed in a back-box which also contains mains wiring or in areas of high humidity. The KP10 runs on 24 V DC supplied through the connecting cable. As such there is no mains voltage present in the KP10 and the unit is often safe to fit in areas where only extra low voltage (ELV) equipment is permitted.
REAR PANEL CONNECTIONS orange green orange / white green / white blue blue / white brown / white brown 1 L+ L - R - R+ 1 Cat5 to KP10 punch down connectors A Cat-5 cable (terminated with an RJ45 jack plug) is used to connect the KP10 to an AH10 hub or A-BUS Ready receiver. The KP10 has punch down connectors for the eight individual conductors of the Cat-5 cable (use a small flat-bladed screwdriver).
KP10 A-BUS keypad 2 Gain adjust The maximum output of the KP10 can be limited by turning these down. Alternatively, if the sound level is too quiet, the Gain can be turned up. 3 Mode switch Selects between AH10 mode and Standard A-BUS Ready/Incognito Ready mode. 4 Speaker output Connect to a pair of speakers with two runs of standard high-quality speaker cable. Speakers of at least 88 dB SPL for 1W @ 1 metre efficiency should be used with the KP10. Speakers from 4–8 ohms can be used.
KEYPAD CONTROLS 3 4 5 2 6 1 The six LEDs indicate the function status of the KP10.
KP10 A-BUS keypad 7 Standby/On Press to switch the keypad between On and Standby mode. By pressing and holding the Standby button for about 2 seconds, all KP10s connected to the AH10 hub will be turned off. If the KP10 is connected to a Cambridge Audio Incognito Ready Amplifier rather than an AH10 hub, the amplifier will be turned off. 8 Volume up Press to increase the volume or other sound adjustment. 9 Source select (right) Use this key to select the current active source.
OPERATING INSTRUCTIONS Important! As mentioned previously, the KP10 can be switched between two modes of operation; a standard A-BUS mode for compatibility with other manufacturers A-BUS Ready equipment (Standard A-BUS/Incognito Ready mode), and an Incognito A-BUS hub mode (AH10 mode). When used with other manufacturers A-BUS Ready equipment the keypad MUST be switched to “Standard A-BUS/Incognito Ready” mode or they will not work.
KP10 A-BUS keypad After holding both buttons down for a short period, the second LED on the keypad will light indicating that Bass adjust mode has been activated. In this mode pressing the Volume up/down keys will adjust the Bass (low frequencies) level. Bass Treble Balance Fader Continuing to hold both keys down will light the third LED indicating that Treble adjust mode has been activated. In this mode pressing the Volume up/down keys will adjust the Treble (high frequencies) level.
LOCAL SOURCE SELECTION Note: This feature is only available if the KP10 is part of a full Incognito multi-room system with one or two Local Input Modules (LM10) fitted. 2 3 4 5 The local source selection mode will need to be activated to configure the KP10 correctly. This mode is only available when the Mode Switch is set to “AH10” mode. LM10s can only be used in this mode. Please refer to your LM10 Installation Guide for more information.
KP10 A-BUS keypad Continuing to hold Volume up and Power buttons will light LED 5, to indicate that Off mode is available for selection, and no source will be selected. To select these modes, wait till the corresponding LED is lit and then release Power and Volume up buttons. Note: If no adjustment is made the system will automatically go back to volume adjustment after two seconds. If “Standard A-BUS/Incognito Ready” mode is selected on the Mode switch, the KP10 will only rotate round the main 6 sources.
TECHNICAL SPECIFICATIONS Input impedance Frequency response THD S/N ratio Volume control range Bass control range Treble control range Balance control range Preamp output IR pass through Speaker impedance Power requirement 45 k ohms 20Hz – 20kHz +/- 1dB <0.
KP10 A-BUS keypad LIMITED WARRANTY Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). Cambridge Audio will repair or replace (at Cambridge Audio’s option) this product or any defective parts in this product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase.
Incognito KP10- EU www.cambridge-audio.com Part No.