Owner's Manual

Remote control
The 851C is supplied with an Azur Navigator remote
control handset that duplicates the front panel control
functions and is also able to control Azur series amplifiers.
The supplied AAA batteries must be fitted before the
remore
control
can be used.
The Azur handset buttons function as described in the
following paragraphs.
@Standby/On
Switches the 851C between On and Standby modes.
0 Open/Close
Opens and closes the CD drawer.
0- 0. 8 Numerics
Enable direct CD track selection. Press the number of
the desired track to begin
playback from the beginning.
To select a track number greater than ten, press the -/--
button followed
by the track number.
@Display
Alters the brightness of the 851C display backlight. There
are two brightness
levels and
an option to switch-off the
backlight.
Play 8 I Stop 0 I Pause 0
Press the relevant button to play, stop or pause a CD .
Note: Depending
on the audio software installed on the
host
personal computer, the
Play and Pause buttons may
also be able to control USB audio playback.
88Skip
Right Skip(~)- Press once to skip forward by one track
on the CD. Press and hold to skip forwards through tracks.
Left
Skip(~)- Press once to skip backward by one track
on the CD. Press and hold to skip backwards through
tracks.
Note: Depending
on the audio software installed on the
host
personal computer, the Skip buttons
may also be
able to control USB audio playback.
8 Scan Right
Press and hold to search while a CD is playing to search
forwards.
8 Scan Left
Press and hold to search while a CD is playing to search
backwards.
8Menu
Press to enter 851C's setup menus. Various 851C
operating parameters can
be configured.
8select
Press to toggle through the five 851C input options. Within
the
Setup menus, press to accept the parameter or option
highlighted
in the display menu.
8 Program, 8 Remain, 8 Repeat,
8Random
Read the 'Operating Instructions' section of this manual
for information
on the functions of these buttons.
8 Filter
Press to toggle through the three 851C digital filter options.
CD Information
8088
0880
8888
08
f?\0
\Ov
88
8088
888®
8888
GG88
azur 851C
The following buttons are used to control Cambridge
Audio Azur range
amplifiers only (such as the matching
851A) or when the 851C has been set to preamp mode
(Digital Volume Enabled).
V: ~ Volume Up/Down
These buttons enable the amplifier volume adjustment for
suitable
Cambridge Audio Azur range amplifiers.
Note: If the 851C Digital Volume feature is enabled, the
handset volume buttons
will
affect the signal output level
from the 851C. Refer to section 'Operating instructions'
for more information.
@Source
Press to toggle through the amplifier inputs.
8Mode
Press to toggle between amplifier volume and balance
control
using the volume up
::1 and down :::_ buttons.
@Speaker A/B
Press to switch between the twin speaker outputs on
Cambridge Audio Azur amplifiers with this facility.
@Mute
Press to mute the output on Cambridge Audio Azur
amplifiers. If the 851C Digital Volume feature is enabled,
this button will mutejunmute the output of the 851C
instead.
The Filter indicator will flash when mute is engaged. Press
Mute again to restore output.
8 81nputs
Used to select sources on matching CA Azur amplifiers.
Apple device compatibility
The Azur 851AC Navigator remote control can control
the basic functions
of Apple devices such as Apple TV
and Apple's iPod/iPhone/iPad range when docked in a
Cambridge Audio or
Apple dock.
Press and
hold the source button that corresponds to the
input that the
Apple product is connected to whilst also
pressing one of the buttons below.
The functions are slightly different depending on the Apple
prodoot. ·
8select
0 Play/pause
0 Stop or Menu
8 8 Press briefly to skip or navigate left or right. Press
and
hold to scan forwards or backwards.
V: ~ Used to control volume andjor navigate menus.
© Used to navigate menus.
Press to
display any additional 851C input signal information available.
In addition, the Azur remote can be paired with up to six specific Apple
devices using
any of the six source buttons. This can be useful if you
have more than one Apple product.
For more information on pairing refer to your Apple device's instruction
manual.
Pairing -
To pair with an Apple device, press and hold the required
source button
along with the
.. button for six seconds. Some devices
like Apple
TV have visual indication once pairing is achieved.
Un-pairing-
To un-pair an Apple device, press and hold any ofthe source
buttons
along with the
~ button for six seconds.
7
I