Learning keypad Installation guide 2 Your music + our passion ENGLISH LK10
Contents Introduction.....................................................3 System setup...................................................4 Installation notes............................................6 Keypad overview.............................................8 On-screen display............................................9 Cloning from the remote control...................10 Settings menus.............................................13 Troubleshooting............................................
Introduction Thank you for purchasing this Cambridge Audio Incognito product. Incognito is a costeffective, modular based multi-room system using standard Cat-5/5e or Cat-6 cable to distribute hi-fi quality sound around a home. Optionally, video can also be distributed using co-axial cable and a VH10 video hub. The LK10 in-wall learning keypad must be used with the Incognito KP10 A-BUS™ audio keypad and LR10 learning remote.
System setup To add your LK10 keypad into your Incognito system, refer to the diagram below: SS10 SS10 Speaker cable Speaker cable KP10 LK10 KP10 Ribbon cable (supplied with LK10) Shift Fav-1 (Set) Menu Title Exit Cat-5/5e cable PS10 AH10 Important: LK10 will only operate when connected to KP10 as part of a complete AH10 hub-based system. It is not compatible with ‘Incognito Ready’ amplifiers.
The LK10 should be placed next to the KP10, using a double J-Box and double Decora™ faceplate (not supplied). Rear view Front view 2 1 1 KP10 connector - Connects the LK10 to the KP10 with the supplied ribbon cable. 2 I.C.P - In-circuit programming socket, used to upgrade keypad software when necessary.
Installation notes The LK10 is fitted on the wall by fixing it into a double USA-type J-Box (electrician’s backbox). All knock-outs in the back-box should be removed to provide maximum ventilation. Where it is desired to fit a mains lighting switch etc next to a keypad, a barrier-box or two single back-boxes must be used (bear in mind it is not preferable to fit the keypad next to a light-switch particularly if the faceplate styles will differ).
ENGLISH LK10 Power requirement The LK10 runs on 24 V DC (@ 250mA max) supplied through the connecting cable from the KP10 keypad. As such there is no mains voltage present in the KP10 and the unit is often safe to fit in areas where only extra low voltage (ELV) equipment is permitted. However, it is imperative that you always check the wiring regulations in force for your application and area.
Keypad overview Buttons numbered 1-8 have dual functions, which are controlled by the Shift button. These buttons generate IR codes or macros cloned from the buttons of the same name on the LR10 learning remote (see later section on Cloning).
LK10 1 2 ENGLISH On-screen display 3 PM 5 4 SHARED 6 EDIT SLEEP LEARN 7 8 9 10 1 2 3 4 5 6 7 8 9 10 Week days - The bar over a letter indicates the day of the week. Alarm - Displayed when the alarm function is set. IR - Indicates when an infra-red signal is sent from the LK10. Time - Displays current time. ‘PM’ appears when 12 hour clock is set. Date - Can be set as Month/Date or Date/Month. Shared - Displayed when sharing a source with another zone connected to the same AH10 hub.
Cloning from the remote control The LK10 can only be used to control source equipment once it has been cloned from the LR10. This transfers the necessary IR codes and macros into the LK10. The Incognito LR10 is a sophisticated learning remote which is able to learn the codes of all the source equipment from their own remotes.
For the LK10 to receive commands, it must be first put into Learn mode. The LK10 has a series of menus that can be accessed by pressing and holding the Shift/Set button on the front panel. The menu options are continuously scrolled on the LK10 display until you release the Shift/Set button. Follow the next steps to complete the cloning operation: LK10 keypad - Receiving data 1 LR10 remote - Transmitting data 2 1. Press and hold the Set button for five seconds.
Cloning from the remote control After approximately 7 minutes the keypad display should show ‘COMPLETE’ and return to normal operation. All data has been transferred. If the clone fails the keypad will show ‘ERROR’ or ‘TIMEOUT’. Put the transmitting LR10 remote back into Clone mode and repeat the process. Note: Once the cloning process has been started it must be completed, as it overwrites the software in the receiving LK10 keypad.
Settings menus Note: You still use your KP10 keypad to control audio functions (volume adjustment, source selection etc). To personalise other settings of the LK10, press and hold the Set button for four seconds to activate the Settings menus (Fig. 1).
Settings menus Alarm menu Press the Set button for five seconds and release when ‘ALARM?’ is displayed on the screen. Alarm Hour Minute Days Source On/Off Use the and to navigate the menu. buttons Use the and buttons to adjust the desired option. Shift Fav-1 (Set) Menu Title Exit Note: When a Source is selected, it will display the default Source programmed into the KP10 keypad. Days When selecting ‘DAYS’, use the and Monday to Friday, weekend or everyday.
Sleep menu This menu allows you to set the time at which the LK10 will automatically switch off. Press the Set button for five seconds and release when ‘SLEEP?’ is displayed on the screen. Sleep Hour Minute On/Off Use the and to navigate the menu. buttons Use the and buttons to adjust the desired option.
Settings menus Setup menu This menu lets the user manually set the time and date of the LK10. Press the Set button for five seconds and release when ‘SETUP?’ is displayed on the screen. Setup Hour Minute Date/Month Month/Date Year Use the and to navigate the menu. buttons Use the and buttons to adjust the desired option. Shift Fav-1 (Set) Menu Title Exit Note: The time and date will also be set automatically after a download from the LR10.
Configure menu Press the Set button for five seconds and release when ‘CONFIG?’ is displayed on the screen. Configure 12/24 Hour DD/MM LCD Brightness Use the and to navigate the menu. buttons Use the and buttons to adjust the desired option. Shift Fav-1 (Set) Menu Title Exit 12/24 Hour - Controls the clock display in either 12 or 24 hour format. DD/MM - Sets the order in which the date and month are displayed. LCD Brightness - Controls the LCD brightness level; Bright, dim or off.
Troubleshooting If the LK10 becomes locked and/or ‘ERROR’ appears on the display due to a power interuption or during cloning, follow these steps: 1. Unplug the power to the system and plug back in after one minute. 2. When the power resumes, the LK10 will display distorted text. 3. Clone the LR10 to the LK10 without entering Learn mode. 4. When the LR10 has finished sending, repeat Step 1. Note: Time and date will not be updated in the LK10.
Limited warranty Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). Cambridge Audio will repair or replace (at Cambridge Audio’s option) this product or any defective parts in this product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase.
www.cambridge-audio.com Cambridge Audio is a brand of Audio Partnership Plc Registered Office: Gallery Court, Hankey Place, London SE1 4BB, United Kingdom © 2009 Cambridge Audio Ltd AP20830/2 Registered in England No.
