CXR120/200 AV RECEIVER
Contents Important safety instructions ................................................................... 3 Limited warranty....................................................................................... 4 Front panel controls................................................................................. 5 Rear panel connections............................................................................ 5 Main remote control.........................................................................
CXR120/200 Important safety instructions For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply. They will also enable you to get the best performance from and prolong the life of the unit: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. D o not block any ventilation openings.
Limited warranty Ventilation Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). Cambridge Audio will repair or replace (at Cambridge Audio's option) this product or any defective parts in this product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase. Ensure that small objects do not fall through any ventilation grille.
CXR120/200 ENGLISH Front panel controls CX R200 4 7 5 11 6 8 3 9 1 HDMI 8/ MHL 2 1. Standby/On 2. Phones 10 For suitable headphones – connection will mute the main zone speakers. 5. Zone (CXR200 only) Press this button followed by Standby/On or Source +/- to change Zone 2. When illuminated, indicates that Zone 2 is On. 8. Menu 9. Back 3. Tuning +/- 6. Display 10. USB / MP3 / HDMI/ MHL Inputs Used to tune FM/AM frequencies and presets for the built-in Tuner. Status window. 7.
Main remote control 1. Backlight button Illuminates the buttons. 2. Standby/On 3. Source buttons 1 2 Pressing the FM/AM button a second time toggles between FM and AM. The TV button selects TV-ARC (Audio Return Channel). Sources The SM button selects the StreamMagic module. 4. Volume 5. Back 1 2 3 5 6 7 8 SM MP3 FM/AM TV 3 4 CXR200 Press to return to the previous menu. 6. Home Turns On and Off the on-screen setup menu. 7. Skip Skips between tracks on the StreamMagic module. 8.
CXR120/200 Switch the power off before making connections. Ensure that correct polarity is maintained. Use 4mm plugs for direct insertion into the speaker terminals. Surround back/height, Bi-amp and Zone 2 speaker connections can all be connected to speakers, but only one will be active. This can be set in the Speaker Configuration menu. 10mm Powered subwoofer Centre speaker Phono/RCA cable 7.1 Right 5.
Digital audio connections BD/DVD player Out OR 1 Pre Out OR 2 2 2 Audio player/recorder (Tape/MD/CD-R) OR Out Out 8 Sub Out Centre Subwoofer Surround Right Front Right Front Left Surround Left DVD-A SACD player Pre Out 1 OR 5.1/7.
HDMI connections 4K video resolution The source resolution cannot be greater than that of the TV you are using consult your HDMI source and TV manual and adjust accordingly. The CXR supports 4K video resolution. Use a high speed HDMI cable when connecting 4K devices. Ensure that the HDMI output of your Blu-ray player has been set to 'Raw' to pass the latest high resolution audio formats to the CXR. Note: 4K is not supported on the HDMI/MHL inputs.
Aerial connections Operating instructions Examples FM aerial OR To activate the CXR, switch the Power switch on the rear panel to On then press the Standby/On button on the front panel. Selecting the source FM external aerial (recommended) Select the source by using the Source +/- buttons on the front panel. After 4 to 5 seconds the CXR will select the new source, or it can be selected by pressing the volume knob.
Note: Dolby Digital and DTS formats can sometimes carry less channels than their maximum such as Dolby Digital (2/0) which means a Dolby Digital encoded signal which is actually only carrying a two channel stereo signal (other channels inactive). Known also as DTS (3/2) or DTS 5.1, DTS provides (up to) 5.
Setup menu Speaker setup Refer to the following diagrams for typical examples of loudspeaker setups. Speaker configuration CXR Setup Menu 5.1 ► Speaker Setup Speaker Configuration Input Setup Auto Setup Zone 2 Settings Unit Metres Network Setup SW Selection Subwoofer1+Subwoofer2 General Settings Back Amp Configuration Bi-Amp ► Enter HDMI Output Setup Advanced Setup First select the number of subwoofers you have connected 'SW Selection' and if you have a 7.
Once finished press the Enter button on the remote to accept the setup. Highlight 'Test Tone' and press Enter. Use the navigation button on the remote to move from speaker to speaker and adjust the level until all are at the same volume using either the Front Left or Right as a reference. CXR Speaker Configuration C FL Front Left FR SW1 SL SR SBL SBR Size Small Distance 2.4m Level -2.
Input setup cont. Stereo processing Choose preferred stereo processing mode for the current source. Multichannel processing Controlling zone 2 You can use the main remote handset, the buttons on the front of the unit itself or the Cambridge 'Connect' App to control Volume, source and mute. Choose preferred multichannel processing mode for the current source. From the remote press and hold the Zone 2 button followed by the feature you require.
Select 'Scan for Networks', select your wifi network and then enter your password. CXR Setup Menu Speaker Setup TV ARC (HDMI out 1) ARC allows a TV to send audio back down its incoming HDMI so that you can play back the audio from a TV source whilst you watch its picture. CEC control Network Input Setup Turn on to enable CEC control features. Zone 2 Settings Network Setup CEC power off control General Settings HDMI Output Setup Allows the CXR to be switched off into standby by the TV.
HDMI output setup cont. Network software update DTS-HD speaker re-map The CXR can be updated via the StreamMagic module connected to the internet. Updates of the StreamMagic module itself can only be started from the Cambridge Connect app or the Web administration interface. When playing back a DTS-HD track the CXR can electronically reposition your speakers to match the setup used in the original recording studio. This is done automatically in most cases, but for 7.
Cambridge Audio is a brand of Audio Partnership Plc Registered Office: Gallery Court, Hankey Place London SE1 4BB, United Kingdom Registered in England No. 2953313 © 2016 Cambridge Audio Ltd AP33863/3-A www.cambridgeaudio.