Installation and Operation Instructions ELECTRIC FIREPLACE X35WMEF1BLK X35WMEF1WHT REV18-01
1
Important Safety Instructions 3-5 Listing Approvals 6 Product Dimensions 7 Locating Fireplace 8 Unpacking and Testing Fireplace 9 Grounding Instructions 9 Installation 10-11 Finishing Checklist 12 Operating Instructions 12-13 Replacing The Rock/Log Set 14 Trouble shooting 15 2
IMPORTANT SAFETY INSTRUCTIONS 1 Prior to plugging your heater into an electrical outlet, verify that the house circuit breakers for the outlet are on. 2 The heater may emit a slight, harmless odor when first used. This odor is normal and it is caused by the initial heating of internal heater elements and will not occur again. 3 If your heater does not emit heat, consult the operation section of this manual for further information. 4 Use with a CSA or UL certified surge protector.
IMPORTANT SAFETY INSTRUCTIONS When using this electric fireplace, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1 .Read all instructions before using this electric fireplace. 2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from top,front and sides of heater. 3.
IMPORTANT SAFETY INSTRUCTIONS 11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater. 12. To prevent possible fire, do not block air intakes in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 13. The electric fireplace has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. 14.
This heater has been tested in accordance with the CSA Standards.
35.0" 17.7" 13.
LOCATING FIREPLACE WARNING: Dueto high temperatures,this electric fireplace should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (o.9m) from top,front and sides of heater. WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container. CAUTION: Do not expose the electric fireplace to the elements (such as rain, etc.
Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates properly. To do this, plug the unit's power supply cord into a conveniently located 120-Volt grounded outlet. This insert is for use with 120 Volts. The cord has a plug as shown in (A) of Figure 2 given below. An adapter as shown in (C) is available for connecting three-blade groundingtype plugs to two-slot receptacles.
WARNING: RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runned or the like. Arrange cord away from traffic area and where it will not be tripped over WARNING: RISK OF FIRE! To prevent a possible fire, do not block air intake or exhaust in any manner. Do not use on soft surfaces where openings may become blocked.
3 11
>Power supply service must be completed prior to finishing to avoid reconstruction. >Heater vents and air openings cannot be covered in any circumstances. Once the unit has been properly connected to a grounded electrical outlet, it is ready to operate. Note: Ensure the house circuit breakers for the power supply are turned on. Main Power Switch: The Main Power Switch is located on the right side of the unit. Figure 4 illustrates the location of the switch. The”I”indicates ON and "O" indicates OFF.
The manual controls are located on the left side of the fireplace. You have the following controls: 1. Power ON/OFF: Power to the unit 2. Flame brightness controls: Allows you to adjust the flame to suit your mood. Press to increase flame brightness and to decrease flame brightness. You must press the button Several times to see the full flame effect. 3. Low heat: 700 watts 4. High heat: 1350 watts Please note: The heater touch panel control must be pressed 2 times to achieve high heat. 5.
Replacing The Rock/Log Set TO CHANGE LOG/ROCK SET (NOTE: MAKE SURE FIREPLACE IS TURNED OFF AND HAS BEEN UNPLUGGED FROM ELECTRICALOUTLETBEFOREATTEMPTINGTOCHANGETHELOG/ROCKSET): 1. Place fireplace on a flat, level surface (FIG 1). 2. Remove 3 screws located on each side of glass face of fireplace (FIG 2 and FIG 3). 3. Remove screws that attach the log/rock set to the front of fireplace (FIG 4). 4. Replace with the desired set(log/rock) and re-assemble new set by inserting and tightening screws(FIG 5). 5.
WARNING: Turn off the appliance, unplug and let cool for at least 10 minutes before attempting to service. Only a qualified professional should attempt mpt to service or repair the appliance. PROBLEM 1.No power, no indicator lights POSSIBLE CAUSE Insert was not plugged in CORRECTIVE ACTION Make sure that power cord is plugged into 120V outlet 2.No power, no indicator lights No power at outlet Check circuit breaker or fuse 3.