Installation and Operation Instructions ELECTRIC FIREPLACE For 42", 50", 60", 72", and 78" Wall-Mount Models
Tool list 2 Assembly Instructions 2-3 Important Safety Instructions 3-4 Listing Approvals 5 Glass Particles Installation Instructions 6 Product Dimensions 7-8 Installation 9-10 Operating Instructions 11 Remote Control Instructions 12 Temperature Limiting Control 13 Trouble Shooting 13 Cleaning 13 1
Suggested tools: Phillip head screw driver, power drill, drill bit, and a tape measure. Unit needs to be hung on wall stud for more security and stability. (1) Fireplace assembly 1 PC (2) Steel holder 42"/50"/60" (3) Remote Control 1 PC 72"/78" (4) Screw 1 PC 8 PCS ̛4mm x 40mm Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Avoid rubbing or scratching the surface with rough or abrasive objects.
2. The heater may emit a slight, harmless odour when first used. This odour is normal and it is caused by the initial heating of internal heater parts and will not occur again. 3. If the heater does not emit heat, Consult your User’s Guide for further information.
heater is in operation it must not be left unattended. 5. Always unplug the heater when not in use. 6. Do not operate any heater with damaged cord or plug or after the heater has malfunctioned or has been dropped or damaged in any manner. Return heater to an authorised service facility for repair. 7. Do not use outdoors. 8. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heaters where it may fall into a bath tub or other water container. 9.
LISTING APPROVALS This heater has been tested in accordance with the CSA Standards. Model Number: X42WMEF1BLK X42WMEF1WHT X50WMEF1BLK X50WMEF1WHT X60WMEF1BLK X60WMEF1WHT X72WMEF1BLK X72WMEF1WHT X78WMEF1BLK X78WMEF1WHT Length: Height: Depth: 42.0 19.8 4.7 50.0 19.8 4.7 60.0 19.8 4.7 72.0 19.8 4.7 78.0 19.8 4.
GLASS PARTICLES INSTALLATION INSTRUCTIONS 1.To remove the outer glass around the bracket, undo the mounting screws (red arrows)(①、②、③) 2.Remove the outer glass ( ④ ) 3.Carefully take out the log set, adjust the screws (red arrows) (⑤、⑥、⑦) 4.Gently put the glass crystals into place ( ⑧ ) 5.
PRODUCT DIMENSIONS DO NOT COVER 4.7 19.
42"/50"/60" 72"/78" Mounting Bar 42"/50"/60" 72"/78" BACK VIEW PRODUCT DIMENSIONS WARNING: Due to high temperatures, this electric fireplace should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36" from the top of the heater. WARNING: Never locate this electric fireplace where it may fall into a bathtub or other water container.
UNPACKING AND TESTING FIREPLACE Carefully remove the unit from the box. Prior to installing the unit, test to make sure the unit operates properly. To do this, plug the unit's power supply cord into a conveniently located 120 Volt grounded outlet. INSTALLATION WARNING: RISK OF FIRE! The power cord must not be pinched or against a sharp edge. Secure cord to avoid tripping or snagging to reduce risk of fire, electric shock or personal injury. Do not run cord under carpeting.
INSTALLATION Model 1: 42"/50"/60" 42"/50"/60" screws Front view of wall back view of fireplace 72"/78" 72"/78" Model 2: Trim Piece Remove the glass pane first, set the fire box into the wall. Secure the side trim pieces on the wall with screws. Reinstall the glass pane onto the firebox with screws.
OPERATING INSTRUCTIONS DISPLAY 6 5 4 3 2 1 LOCATION The master power switch is located on the right side of the appliance. The control panel is on the right corner of the glass. MASTER SWITCH The master switch controls the power supply to the appliance. Turn the switch to “I” to connect power and turn the switch to “O” to cut the power. There will be a chiming sound when turning to “I”. 1.
REMOTE CONTROL FEATURES 1. Install the CR2025 3V battery in the remote control. 2. Turn the master switch on the e-fireplace to ‘I’ so that it can receive the signal from the remote control. 3. Lock the colour for the flame using button 1. Lock the colour for the Log using button 2. Press the button to see and choose the colour. 4. CAUTION: Never leave the e-fireplace unattended while heating. 5. Refer to Page 11 control buttons/functions for the other buttons on the remote control.
TEMPERATURE LIMITING CONTROL This heater is equipped with a Temperature Limiting Control. Should the heater reach an unsafe temperature, (115 degrees Celsius) the heater will automatically turn off. To reset: Unplug unit from wall, wait for 5 minutes, plug back in and continue to use. TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSES Fireplace doesn't work. Fireplace inner components are overheating or the home circuit breaker has tripped.