User manual

3 / 42
www.camcoaudio.com
USER MANUAL
Q-POWER 14
|
POWER AMPLIFIER
CONTENTS
Welcome to the Q-POWER 14 User Manual 4
Important Safety Instructions 5
Explanation of Symbols 7
EC Declaration of Conformity 8
1. Welcome to CAMCO 9
1.1 Unpacking 9
2. The Amplifier 10
2.1 The Q-POWER 14 Front 11
2.2 The Q-POWER 14 Rear 11
3. Mains 12
3.1 Mains Supply 12
3.2 Mains Plugs and Cables 12
3.3 On / Off Switch 12
3.4 Mains Voltage Range 13
3.5 Inrush Current Limitation 13
3.6 Mains Power Consumption and Current Draw 14
3.7 FuseProtect™ Limiter - Mains Circuit Breaker selection 15
4. Mounting 16
4.1 Mounting Dimensions Q-POWER 14 16
4.2 Cooling 16
4.3 Fans 16
5. Input and Output Connectors 17
5.1 Analogue Input Connectors 17
5.2 SPEAKON
®
Loudspeaker Output Connectors 18
6. Operation 19
6.1 Indicators 19
6.1.1 ON LEDs 19
6.1.2 SIGNAL/Protect LEDs (multifunctional) 19
6.1.3 I-OUT Output Current LEDs 19
6.1.4 CLIP LEDs (multifunctional) 19
6.2 Controls 19
6.2.1 Volume Control 19
6.2.2 Gain Selector 19
6.2.3 Clip Limiter Switch 19
6.3 CAMCO USB MCB Updater 20
7. Protections 21
7.1 Power Amp Protection Systems 21
7.1.1 Clip Limiter 21
7.1.2 SOA Protection 21
7.1.3 DC Protection 21
7.1.4 DC Servo 21
7.1.5 Output Current Limiter 21
7.1.6 Underimpedance Limiter 21
7.1.7 Output Short Circuit Protection 21
7.1.8 Thermal Limitation and Protection 21
7.1.9 High Frequency Protection 22
7.2 Mains and Power Supply Protections 22
7.2.1 Inrush Current Limitation 22
7.2.2 Mains Overvoltage Detection 22
7.2.3 Mains Surge Overvoltage Protection 22
7.2.4 Mains Failure Detection 22
7.2.5 Mains Overcurrent Limiter 22
7.2.6 Over Current Protection 22
7.2.7 Fuse / MCB Protection (FuseProtect™ Limiter) 22
7.2.8 Thermal Protection 22
8. Filter Cleaning 23
8.1 Removing the Filter System and Cleaning 23
9. Volume Control Security Cover 24
9.1 Mounting the Volume Control Security Cover 24
10. Troubleshooting 25
10.1 No reaction when switching the amplifier on 25
10.2 All four signal LEDs are red, the green On-LEDs are off 25
10.3 All green On-LEDs are on, but there is no sound 25
10.4 Sound is distorted 25
10.5 Sound is distorted although Clip Limiter is On 25
10.6 Signal and Clip LED of one or more channels are red
intermittently 26
10.7 Output power lower than usual 26
10.8 The amplifier gets hot very quickly 26
10.9 The CAMCO USB MCB Updater application does not
connect to the amplifier 26
11. Specifications 27
12. Typical Performance Diagrams 30
12.1 Gain vs. frequency, 120 W output power 30
12.2 Phase vs. frequency 30
12.3 THD @ 1 kHz vs. input level 30
12.4 THD vs. frequency, 120 W output power 30
12.5 Channel separation vs. frequency @ 3 × 120 W / 4 Ω 31
12.6 DIM100 vs. input level @ 4 Ω load 31
12.7 Common mode rejection ratio vs. frequency 31
12.8 FFT of noise level vs. frequency 31
12.9 Output impedance vs. frequency 32
12.10 Damping factor vs. frequency 32
13. Unit Conversion Equations and Lookup Table 33
13.1 Unit Conversion Equations 33
13.2 Lookup Table 33
14. Warranty Information 34
14.1 Summary of Warranty 34
14.2 Items Excluded from This Warranty 34
14.3 What CAMCO Will Do 34
14.4 How to Obtain Warranty Service 34
14.5 CAMCO Product Improvement 34
15. Service Information 35
16. Maintenance Information 36
17. Decommissioning 36
Company information 37
Changes Made to The Amplifier / Notices 38
Hole template for Volume Control Security Cover 40